CM30网络模块介绍.doc

CM31/CM32 ProfibusDP 网络模块特征：1、 Profibus DP从站协议可达12M通讯波特率。2、 两个串行端口：RS232 ； RS232/RS422/RS485 MUX32。3、 两个HS/HL系列的天线端口。4、 一个工业水准的输入口/两个工业水准的输入输出口。5、 DOS兼容的处理器。6、 IP66/IP31的防护等级。 如下图：CM31接口端子图；CM32接线端子图； CM31/CM32系统构架图：CM30系列 Profibus模块的连接器和附件：配件描述 零件号码Profibus In/Out Cable AssemblyCBL-1438-xxProfibus 12mm Drop-T, FFMCBL-1446Termination Plug 00-1098Field Mountable 12mm Male Output 46-1442Field Mountable 12mm Male Input46-1443Note 1: xx = cable length in meters (01,02,03,06,30)Note 2: If the Profibus host requires a DE9 connector, use Siemens SINEC L2 Bus connector (6ES7 972-0BA10-0XA0CM30系列通讯协议的跳线设置：CM30系列Profibus模块的Profibus地址拨码开关：Switch 1 2 3 4 5 6 7 8Setting OFF OFF OFF OFF OFF OFF ON ON Value: 0 0 + 0 + 0 + 0 + 0 + 2 + 1 Address: = 3Switch 1 is reserved and should be left in the OFF position.CM31模块LED指示灯：LEDColorDescriptionCOM1-2GreenSerial communication port 1/2 is activeANT0-1RedHS/HL500 Antenna 0/1 is activeNETWORKGreen Bus is active POWERGreen Power OnCM32模块LED指示灯：LEDColorDescriptionCOM1-2GreenSerial communication port 1/2 is activeANT0-1RedHS/HL500 Antenna 0/1 is activeNETWORKGreen Bus is active POWERGreen Power OnCM30系列Profibus模块，Profibus配置参数：Profibus Parameter ValueManufacture ID CD31 (Hex)ASIC SPC3Max. Number of Inputs32, 64, 128, or 212 bytesMax. Number of Outputs32, 64, 128, or 212 bytesMax. Number of ID 16Number of Diag Bytes 6Number of Parm Bytes 8CM30 系列Profibus模块，Profibus I/O 点配置：Profibus I/O Header + ParameterMaximum Data Config. (Bytes)OverheadLength (Bytes) 326 26 646 5812861222126206CM30系列Profibus I/O Length Examples：Profibus I/O 区域 报头参数 最大数据配置（字节） 段数 占用空间 的长度32 1 12 2032 2 16 1632 3 20 1264 1 12 5264 3 20 4464 5 28 36128 1 12 116128 2 16 112128 3 20 108212 1 12 200CM30系列网络模块的命令字模式：CM30系列网络模块的命令协议：CM30系列网络模块的命令字：Opcode Command(Decimal) 04Tag Fill 05Tag Read 06 Tag Write 09Serial ReadLn (RS232) 10Define Serial Parameters 11Serial Read (RS232) 12Serial Write (RS232) 13Reset Tag Battery Timer 14Clear Serial Buffer 18HMS Tag Write (RS232)20Tag-to-Tag Transfer 30Serial Read (MUX32) 31Serial Write (MUX32) 32HMS Tag Read (MUX32) 33HMS Tag Write (MUX32) 34HMS Tag Fill (MUX32) 39Collect (MUX32) 40Read Auto Polled (MUX32) 41 Write Auto Polled (MUX32) 42HMS Tag Read Auto Polled (MUX32)43HMS Tag Write Auto Polled (MUX32) 44HMS Tag Fill Auto Polled (MUX32) 60Post Tag Read 61Post Tag Write 62Post Serial Read 63Post Serial ReadLn 68Buffer Read 69Buffer Write 120Define ModeCM30系列网络模块的错误：Error Format:Exxx ”Trace Code Message String” (Param1,Param2,Param3,Param4,Param5)Notes Trace Mode is enabled These errors if any are displayed on your terminal through the CM debug portAll events are displayed in Decimal000-099MUX32 related codes100-199 ABX protocol related codes200-299Serial port related codes300-399HS Antenna related codes400-499Reserved500-599Bus related codes600-699Reserved700-799Reserved800-899 Command related codes900-999General message codesEventText (Param1,Param2,Param3,Param4,Param5)001MUX32 Not Enabled. Verify COM2 Config (HW/SW)(Character expected, Character received,)002MUX32 Recv Buffer Overflow (Node Address, Data Size, Buffer Size,)003MUX32 send data exceeds packet size(Node Address, Data Size, Buffer Size,)004MUX32 device response has data length of 0(Node address,)005MUX32 error. Node not active on bus(Node address,)006Cant mix 30 and 40-series commands(Opcode,)007MUX32 error. Node does not respond to command(Node Address,)008MUX32 error. Node has no data to collect(Node address, Node state (0=idle, 1=busy, 2=ready),)009MUX32 node is now ON line(Node address,)010MUX32 node OFF line or not present(Node address,)011MUX32 operation(R/W) failed, status=ERROR(Node address,)100Slave device (ABx) returned error code(Node address or port no., Character received,)101Slave device (ABx) response framing error(Node address or port #, Character expected, Character received,)102Slave device (ABx) returned error code(Node address or port #, Error code returned (See HMS manual),)103Slave device (ABx) timed out looking for a tag(Node address or port #, 8,)200General serial port failure(Port #,)201Com port timeout(Port #,)202Port config error. Invalid baud rate(Opcode, Baud rate value sent,)203Port config error. Invalid parity(Opcode, Parity value sent,)300General HS Antenna failure(Antenna #,)501Data length exceeds bus buffer size(Data length, Max bus buffer size,)800Co