英文图纸技术翻译

1、-05-HNOTES ：（UNLESS OTHERWISE SPECIFIED）:备注：（除非另有说明）1. MATERIAL ：RTP 900-P1700 ZC- BLUE (UDEL POLYSULFONE ，COLOR BLUE). 材料：RTP 900-P1700 RTP 900-P1700 蓝色（聚砜 ，蓝色） NO USED OR RECYCLED MATERIAL PERMITTED . 不允许使用用过的或者回收的材料 PROVIDED RAW MATERIAL LOT CERTIFICATION WITH EACH SHIPMENT WHICH INCLUDES SUPPLIE

2、R NAME LOT NUMBER ，AND MATERIAL TYPE OR SPECIFICATION NUMBER . 提供每一次交付来料原材料批号认证，包括供应商名称批号，材料类型或者规格编号2. ALL EJECTOR PIN AND GATING VESTIGE TO BE FLUSH OR RECESSED WITHIN .005 OF SURFACE. 所有的顶针和水口残留要与部品表面齐平，深入表面最大不能超过0.005 INTUITIVE SURGICAL ENGINEER TO APPROVE ALL GATE AND EJECTOR PIN LOCATIONS . 要与客

3、户确认水口和顶针位置3. NO CRACKS ，FLASH，SINKS，OR KNIT LINES PERMITTED UNLESS APPROVED BY INTUITIVE SURGICAL . 不能有裂纹，披峰，缩水，熔接线，除非客户同意 VISUALLY INSPECT FOR COMPLETE FILL AND IRREGULARITIES 肉眼检查一下打满胶的部品和其他不良4. ALL MOLD RELEASE MUST BE APPROVED BY INTUITIVE SURGICAL ENGINEERING PRIOR TO USE .脱模剂要经过外观工程科同意后使用5. DI

4、AMETRICAL TAPER TO CONFORM TO ISO 594/1-1986 （LUER FITTING ）. 直径的锥形符合ISO 594/1 - 1986(鲁尔接口配件) USE GO/NOGO GAGE DEFINED IN ISO 594/1-1986 ，FIGURE 3C （ISI PN ） TO INSPECT CAVITY .通止规使用参考ISO 594/1-1986，检查前模用FIGURE 3C （ISI PN ） 6. NOT FULLY DIMENSIONED OBTAIN MISSING INFORMATION FROM CAD FILES . 没标注的尺寸参

5、见CAD图纸7. PARTS TO BE CLEAN , WITH NO CONTAMINATION OR LUBRICANT . 部品要干净,没有污染物质或润滑剂 NO VISIBLE PARTICULATE WHEN EXAMINED WITHOUT MAGNIFICATION . 用肉眼检查，不要有可见微粒8. PACKAGE IN CLEAN CLEAR PLASTIC BAGS . 包装使用干净的透明塑料袋 LABEL PACKAGING WITH INTUITIVE S PART NUMBER , REVISION (EG .-01-H),PURCHASE ORDER NUMBER

6、， AND QUANTITY. 包装标签上要有：直观的零件号,修订版本(如.-01-H)，采购订单号和数量。9. PROVIDE DATA FOR ALL SQC POINTS ON FORM OR EQUIVALENT WITH EVERY DELIVERY . 每一次交付，提供数据给所SQC注意点以形式（表格）或类似的形式。 USE C=0 SAMPLING PLAN PER DOP ， “INCOMING INSPECTION” . 每一DOP 使用c=0抽样计划，来料检查-02-BNOTES ：（UNLESS OTHERWISE SPECIFIED）:备注：（除非另有说明）1. MAT

7、ERIAL ：CLEAR POLYCABONATE, CALSS VI, DOW PC 2081-15 材料： PC , 等级VI , DOW(陶氏化学) PC 2081-152. SURFACE FINISH SPI#2 OR BETTER WITH NO GATE OR PARTING LINE 表面 SPI#2处理，或者最好有没水口、分型线3. FINISH ：SPI#4 OR BETTER UNLESS OTHERWISE SPECIFIED 抛光：SPI#4 或者更好除非另有说明4. 100% VIRGIN MATERIAL ONLY ，NO USED OR RECYCLED MAT

8、ERIAL PERMITTED . 100% 纯原料 ，不允许使用用过的或者回收的材料5. ISI ENGINEERING TO APPROVE ALL GATE AND EJECTOR PIN LOCATIONS 所有水口和顶针位置要经过ISI 同意确认6. ALL EJECTOR PIN AND GATING VESTIGE FLUSH TO WITHIN .010 OF SURFACE. 所有的顶针和水口残留不得高出部品表面0.107. Sharp Corners maybe r .005 max 锐角最大半径为0.0058. DRAFT ANGLE IS 1 AS REQUIRED U

9、NLESS OTHERWISE SPECIFIED 按照要求，拔模角度为 1，除非另有说明9. MATING RAD TO BLEND SMOOTHLY . NO MISMATCH PERMISSIBLE. ？ 不允许有段差10. FLASH NOT TO EXCEED .005 “X.010” AND NO LOOSE FLASH PERMITTED 披峰不能超过0.005，不允许有松散的披峰11. VISUALLY INSPECT FOR COMPLETE FILL AND IRREGULARITIES 肉眼检查一下是否打满胶和其他不良12. NO CRACKS OR KNIT LINES

10、 PERMITTED 不能有裂纹，熔接线13. UNDER NORMAL LIGHTING ，REVIEWED FOR 3 TO 5 SECONDS，WITHOUT MAGNIFICATION AT A DISTANT OF 16 TO 18 INCHES THERE SHALL BE NO PARTICULARS OR FIBER LARGER THAN 0.25MM2 AS MEASURED ON A TAPPI CHART .参照TAPPI图表来衡量，在正常照明，16 - 18英寸的距离，没有放大情况下，查看3到5秒钟,没有微粒或纤维大于0.25毫米 2 PACKAGE SHALL BE

11、 BAGGED ,USING BAGS THAT ARE CLEAN ,FREE OF OIL AND DEBRIS WHENNSPECT IN THE SAME MANNER . 包装应该用袋装，袋子应该干净，没有油污和残屑 HEAT SEAL BOTH BAGS .LABEL EACH BAG WITH INTUITIVES NUMBER REVISION LEVEL， QUANTITY ,SUPPLIER LOT NUMBER AND PURCHASE ORDER NUMBER. 热封包装（两头？），包装袋标签上要有：直观的修订版本，数量，供应商批次号，采购订单号14. PROVIDED

12、 RAW MATERIAL LOT CERTIFICATION INSPECTION RESULTS WITH EACH SHIPMENT ，INCLUDE SUPPLIER NAME ，LOT NUMBER AND MATERIAL TYPE OR SPECIFICATION No. 每一次交付，提供原材料的证明检测结果，包括：批次号，材料类型或者规格编号-04-DNOTES ：（UNLESS OTHERWISE SPECIFIED）:备注：（除非另有说明）1. MATERIAL ：NYLON 6-6 ，33% GLASS FIBER FILLED . COLOR ：NATURAL. 材料：

13、尼龙 6-6 ， 加33% 玻纤. 颜色：自然色 VIRGIN MATERIAL ONLY. 只能使用纯原料 PROVIDED RAW MATERIAL LOT CERTIFICATION WITH EACH SHIPMENT WHICH INCLUDES SUPPLIER NAME ，LOT NUMBER AND MATERIAL TYPE OR SPECIFICATION NUMBER 提供每一次交付原材料批号证明，包括：供应商名称，批号，材料类型或者规格编号。2. PART TO BE CLEAN WITH NO CONTAMINATION OR MOLD RELEASE . 部品要干净

14、，不能有污染物或者脱模剂 NO VISIBLE PARTICULATE WHEN EXAMINED WITHOUT MAGNIFICATION . 用肉眼检查，不要有可见微粒3.（WHEN MOLDED）LOCATION OF PARTING LINE ,GATES AND EJECTOR PINS TO BE APPROVED BY INTUITIVE SURGICAL . (注塑时)分型线，水口，顶针的位置要经过外观工程同意 FALSH ,SINKS OR OTHER SURFACE IMPERFACTIONS ARE NOT ALLOWED UNLESS APPROVED BY INTU

15、ITIVE SURGICAL . 披峰，缩水，或者其他表面不良都不允许，除非经过直觉外观同意4.（WHEN MOLDED）GATE VESTIGE TO BE FLUSH OR BELOW SURFACE OF THE PART . (注塑时)水口残留要平齐，或者低于部品表面5.（WHEN MOLDED）PARTING LINE MISMATCH 0.003 MAX （注塑时）分型线段差最大不超过0.003.6. MATING RAD TO BLEND SMOOTHLY . WITH 0.01 MAX MISMATCH ？ 段差最大不超过0.0017. PARTS NEED TO BE CLE

16、AN AND FREE OF OIL AND DEBRIS .部品要干净，没有油污和残屑 PACKAGE PARTS IN DOUBLE BAGS AND SEAL BOTH BAGS. 部品包装在两个袋子并且袋子都要封 LABEL BAGS WITH INTUITIVES PART NUMBER， REVISION LEVEL， QUANTITY , SUPPLIER LOT NUMBER . 包装袋标签上要有：直观的产品番号，修订版本，数量，供应商批次号 ISI IQC TO APPLY LABEL “CLEAN ROOM PARTS” OR EQUIVALENT TO BAG ISI 的

17、IQC 将“打扫房间部品”或相应的标识应用于标签8. ALL DIMENSIONS SYMMETRIC ABOUT CENTER LINES 所有尺寸关于中心线对称-08-E1. MATERIAL: POLYETHERIMIDE, 30% GLASS-FILLED, COLOR: CARBON GREY (RTP 2199 X NS EC-). 材料：PE，加30% 玻纤，颜色：碳灰(RTP 2199 X NS EC-). NO REGRIND OR RECYCLED MATERIAL PERMITTED.不允许有水口料或者再回收的材料2. SURFACE FINISH: 表面处理： EXTE

18、RIOR SURFACES: MOLDTECH MT-11010 OR EQUIVALENT (TOOL TO BE TEXTURED AFTER FIRST ARTICLE APPROVAL) 外表面：MOLDTECH MT-11010 或者 类似处理（FAI合格后，模具要纹） INTERIOR SURFACES: SPI C-1 内表面： SPI C-13. SEE 3D IGES FILE FOR DIMENSIONS NOT ON DRAWING. 图纸上没有的尺寸参见3D IGES(初始化图形交换规范)4. ALL EJECTOR PIN MARKS TO BE FLUSH TO .

19、005 MAX BELOW SURFACE. 所有的顶针印低于物品表面最大不超过0.005 EJECTOR PIN LOCATIONS TO BE APPROVED BY INTUITIVE SURGICAL. 所有水口和顶针位置要经过外观工程同意确认5. GATING VESTIGE TO EXTEND NO MORE THAN .020 FROM SURFACE OF PART. 水口残留最大不能超过部品表面0.020 GATE LOCATION TO BE APPROVED BY INTUITIVE SURGICAL. 水口置要经过外观工程同意确认6. DRAFT AS SPECIFIE

20、D IN THE 3D CAD MODEL. 拔模斜度见3D CAD 模型 NO DFT PERMITTED ON CASTELLATED BORE FEATURES (5 PLACES). 槽型孔不允许有拔模斜度（5个地方）7. PARTS TO BE CLEAN WITH NO CONTAMINATION, MOLD RELEASE OR LUBRICANT. 部品要干净，没有污染物,脱模剂或润滑剂8. NO VISIBLE PARTICULATE OR CONTAMINATION ON PARTS WHEN EXAMINED WITHOUT MAGNIFICATION.肉眼检查时没有可见

21、的微粒或污染物9. NO CRACKS, SINKS OR KNIT LINES PERMITTED. VISUALLY INSPECT FOR COMPLETE FILL AND IRREGULARITIES. 不能有裂纹，缩水，熔接线，肉眼检查一下打满胶的部品和其他不良10. NO FLASH GREATER THAN .005 INCHES. 披峰最大不能超过0.005英寸 NO LOOSE FLASH PERMITTED.不允许有松散的披峰11. PACKAGE PARTS IN CLEAN CLEAR PLASTIC BAGS. 产品包装在干净的透明塑料袋 LABEL EACH BA

22、G WITH INTUITIVES PART NUMBER, REVISION LEVEL, QUANTITY, SUPPLIER LOT NUMBER, AND PURCHASE ORDER NUMBER. 包装袋标签上要有：直观的产品番号，修订版本号，数量，供应商的批次号，采购单号12. PROVIDE RAW MATERIAL LOT CERTIFICATIONS WITH EACH SHIPMENT, INCLUDING: SUPPLIER NAME, LOT NUMBER AND MATERIAL TYPE OR SPECIFICATION NUMBER. 提供每一次交付来料原材料批

23、号认证，包括供应商名称，批次号，材料类型或者规格编号 PACKAGE CERTIFICATION(S) SEPARATE FROM ANY INVOICE PAPERWORK AND INCLUDE IN THE FIRST SHIPPING CARTON.包装认证独立于任何发票文件，包括在第一次纸箱交付13. PROVIDE CERTIFICATE OF COMPLIANCE WITH EACH SHIPMENT INCLUDING SUPPLIER NAME, SUPPLIER LOT IDENTIFICATION, INTUITIVES PART NUMBER, REVISION, PU

24、RCHASE ORDER NUMBER, QUANTITY, SIGNATURE AND TITLE OF SIGNEE, 提供每一次交付的合格证明，包括：供应商名称，供应商批次证明，直观的部品番号，修订版本号，采购订单号，数量，签名及签署者的头衔 AND THE FOLLOWING (OR AN EQUIVALENT) STATEMENT “I CERTIFY THAT THE PARTS IN THIS SHIPMENT WERE MANUFACTURED IN CONFORMITY WITH THE REQUIREMENTS IN THE PART DRAWING AND PURCHAS

25、E ORDER FOR THE REFERENCED PART.” 并且下述（一个类似的）声明“我保证这批货制造符合部品图纸及相应部品采购订单要求”14. PROVIDE RoHS CERTIFICATE OF COMPLIANCE WITH EACH SHIPMENT. 提供每个装运RoHS证书15. APPROXIMATE PART VOLUME: 0.70 CUBIC INCHES.部品近似体积：0.70立方英寸16. DFT- INDICATES A DIMENSION THAT IS DECREASING IN VALUE DUE TO DRAFT ON THE PART. DFT

26、- ： 表示体积的减小是由于部品的拔模处理 DFT+ INDICATES A DIMENSION THAT IS INCREASING IN VALUE DUE TO DRAFT ON THE PART. DFT + ： 表示体积的增加是由于部品的拔模处理17. OVERMOLD MAGNET, ISI PN (MAGNET SALES AND MANUFACTURING INC. PN 26DRE1608) INTO CHASSIS AT LOCATION INDICATED. 关于模具磁铁，ISI PN （磁铁销售和制造 INC. 包括 PN 26DRE1608 ）在底盘位置显示 性能参数

27、Performance Number；可塑性指数Plasticity Number MAGNET MUST NOT BE BROKEN OR CRACKED THRU. 磁铁不能碎裂。 NO FRAGMENTS OR FLAKES PERMISSIBLE. 不允许有碎片 MINOR CHIPS OR COSMETIC IMPERFECTIONS ARE ACCEPTABLE. 较小的碎片个表面不良是可以接受的-07-F1. MATERIAL: POLYETHERIMIDE, 30% GLASS-FILLED, COLOR: CARBON GREY (RTP 2199 X NS EC-). 材料

28、：PE , 加30% 玻纤，颜色：碳灰(RTP 2199 X NS EC-). NO REGRIND OR RECYCLED MATERIAL PERMITTED.不允许有水口料或者再回收的材料2. SURFACE FINISH: 表面处理： INDICATED SURFACES: MOLDTECH MT-11010 OR EQUIVALENT (TOOL TO BE TEXTURED AFTER FIRST ARTICLE APPROVAL)如图所示表面：MOLDTECH MT-11010 或者类似的处理（FAI合格后，模具要晒纹） ALL OTHER SURFACES: SPI C-1其他

29、表面：SPI C-13. SEE 3D IGES FILE FOR DIMENSIONS NOT ON DRAWING.图纸上没有的尺寸参见3D IGES(初始化图形交换规范)4. ALL EJECTOR PIN MARKS TO BE FLUSH TO .005 MAX BELOW SURFACE. 所有的顶针印低于物品表面最大不能超过0.005 EJECTOR PIN LOCATIONS TO BE APPROVED BY INTUITIVE SURGICAL.所有水口和顶针位置要经过外观工程同意确认5. GATING VESTIGE TO EXTEND NO MORE THAN .010

30、 FROM SURFACE OF PART. 水口残留最大不能超过部品表面0.010GATE LOCATION TO BE APPROVED BY INTUITIVE SURGICAL.水口位置要经过外观工程同意确认6. DRAFT AS SPECIFIED IN THE 3D CAD MODEL. 拔模斜度见3D CAD 模型NO DFT PERMITTED ON CASTELLATED BORE FEATURES (6 PLACES). 槽型孔不允许有拔模斜度（6个地方）7. PARTS TO BE CLEAN WITH NO CONTAMINATION, MOLD RELEASE OR

31、LUBRICANT.部品要干净,没有污染物质，脱模剂或润滑剂8. NO VISIBLE PARTICULATE OR CONTAMINATION ON PARTS WHEN EXAMINED WITHOUT MAGNIFICATION.肉眼检查时没有可见的微粒或污染物9. NO CRACKS, SINKS OR KNIT LINES PERMITTED. 不能有裂纹，披峰，缩水，熔接线VISUALLY INSPECT FOR COMPLETE FILL AND IRREGULARITIES.肉眼检查一下打满胶的部品和其他不良10. NO FLASH GREATER THAN .005 INCH

32、ES. 披峰最大不能超过0.005英寸NO LOOSE FLASH PERMITTED.不允许有松散的披峰11. PACKAGE PARTS IN CLEAN CLEAR PLASTIC BAGS.包装使用干净的透明塑料袋LABEL EACH BAG WITH INTUITIVES PART NUMBER, REVISION LEVEL, QUANTITY, SUPPLIER LOT NUMBER, AND PURCHASE ORDER NUMBER.包装标签上要有：直观的零件号, 修订版本，数量，供应商批次号和采购订单号12. PROVIDE RAW MATERIAL LOT CERTIFI

33、CATIONS WITH EACH SHIPMENT, INCLUDING: SUPPLIER NAME, LOT NUMBER AND MATERIAL TYPE OR SPECIFICATION NUMBER. 提供每一次交付来料原材料批号认证，包括供应商名称，批次号，材料类型或者规格编号PACKAGE CERTIFICATION(S) SEPARATE FROM ANY INVOICE PAPERWORK AND INCLUDE IN THE FIRST SHIPPING CARTON.包装认证独立于任何发票文件，包括在第一次纸箱交付13. PROVIDE CERTIFICATE OF

34、COMPLIANCE WITH EACH SHIPMENT INCLUDING SUPPLIER NAME, SUPPLIER LOT IDENTIFICATION, INTUITIVES PART NUMBER, REVISION, PURCHASE ORDER NUMBER, QUANTITY, SIGNATURE AND TITLE OF SIGNEE,提供每一次交付的合格证明，包括：供应商名称，供应商批次证明，直观的部品番号，修订版本号，采购订单号，数量，签名及签署者的头衔， AND THE FOLLOWING (OR AN EQUIVALENT) STATEMENT “I CERTI

35、FY THAT THE PARTS IN THIS SHIPMENT WERE MANUFACTURED IN CONFORMITY WITH THE REQUIREMENTS IN THE PART DRAWING AND PURCHASE ORDER FOR THE REFERENCED PART.”并且下述（一个类似的）声明“我保证这批货制造符合部品图纸及相应部品采购订单要求”14. PROVIDE RoHS CERTIFICATE OF COMPLIANCE WITH EACH SHIPMENT.提供每个装运RoHS证书15. APPROXIMATE PART VOLUME: 0.75

36、 CUBIC INCHES.部品近似体积：0.75立方英寸16. DFT- INDICATES A DIMENSION THAT IS DECREASING IN VALUE DUE TO DRAFT ON THE PART. DFT - ： 表示体积的减小是由于部品的拔模处理 DFT+ INDICATES A DIMENSION THAT IS INCREASING IN VALUE DUE TO DRAFT ON THE PART.DFT + ： 表示体积的增加是由于部品的拔模处理-01-H1. MATERIAL: INFINITY INSTRUC PCABSVHFMR, MEDICAL

37、GRADE (-MD), BLUE (NC CONC BL 284C)材料：INFINITY INSTRUC PCABSVHFMR ，医用级 （-MD）, 蓝色（NC CONC BL 284C）NO USED OR RECYCLED MATERIAL PERMITTED. 不允许使用用过的或者回收的材料PROVIDE RAW MATERIAL LOT CERTIFICATION WITH EACH SHIPMENT WHICH INCLUDES SUPPLIER NAME, LOT NUMBER, AND MATERIAL TYPE OR SPECIFICATION NUMBER.提供每一次交

38、付来料原材料批号认证，包括供应商名称，批次号，材料类型或者规格编号2. ALL EJECTOR PIN AND GATING VESTIGE FLUSH TO BE RECESSED WITHIN .005 OFSURFACE.所有的顶针和水口残留要与部品表面齐平，深入表面最大不能超过0.005INTUITIVE ENGINEERING TO APPROVE ALL GATE AND EJECTOR PIN LOCATIONS.所有水口和顶针位置要经过外观工程同意确认3. NO CRACKS, FLASH, SINKS, OR KNIT LINES GREATER THAN .005 PERM

39、ITTED.不能有裂纹，披峰，缩水，熔接线不能超过0.005VISUALLY INSPECT FOR COMPLETE FILL AND IRREGULARITIES.肉眼检查一下打满胶的部品和其他不良4. NOT FULLY DIMENSIONED. OBTAIN MISSING INFORMATION FROM CAD FILES.没标注的尺寸参见CAD图纸DEFAULT TOLERANCE OF +/- .020默认公差 ：0.0205. PARTS NEED TO BE CLEAN AND FREE OF OIL AND DEBRIS.部品要干净，没有油污和残屑PACKAGE PART

40、S IN DOUBLE BAGS AND SEAL BOTH BAGS. 部品包装在两个袋子并且袋子都要密封LABEL BAGS WITH INTUITIVES PART NUMBER, REVISION LEVEL, QUANTITY, SUPPLIER LOT NUMBER, AND PURCHASE ORDER NUMBER .包装袋标签上要有：直观的产品番号，修订版本号，数量，供应商批次号，采购订单号，ISI IQC TO APPLY LABEL “CLEAN ROOM PARTS” OR EQUIVALENT TO BAG.ISI 的IQC 将“打扫房间部品”或相应的标识应用于标签6

41、. PROVIDE CERTIFICATION OF COMPLIANCE WITH EACH SHIPMENT INCLUDING SUPPLIER NAME, SUPPLIER LOT IDENTIFICATION, INTUITIVES PART NUMBER, REVISION, PURCHASE ORDER NUMBER, QUANTITY, SIGNATURE AND TITLE OF SIGNEE, 提供每一次交付的合格证明，包括：供应商名称，供应商批次证明，直观的部品番号，修订版本号，采购订单号，数量，签名及签署者的头衔，AND THE FOLLOWING (OR AN EQU

42、IVALENT) STATEMENT “I CERTIFY THE REQUIREMENTS IN THE PART DRAWING AND PURCHASE ORDER FOR THE REFERENCED PART.”并且下述（一个类似的）声明“我保证这批货制造符合部品图纸及相应部品采购订单要求”7. SUPPLIER TO MAINTAIN SOFT COPY OF MATERIAL AND PROCESS CERTIFICATIONS.供应商要保有材料软拷贝 供计算机阅读的复制件 副本和认证过程8. PART INTENDED TO MATE WITH -02.与-02装配-08-C1

43、. MATERIAL: SEE TABLE BELOW (CERTS MUST MATCH DRAWING REQUIREMENTS)材料：参阅下面表格 （确实的事情必须匹配图纸要求）2. SURFACE FINISH:表面处理：EXTERIOR SURFACES: SPI B-1外表面：SPI B-1INTERIOR SURFACES: SPI C-1内表面：SPI C-13. SEE 3D CAD FILE FOR DIMENSIONS NOT ON DRAWING.没标注的尺寸参见CAD图纸4. ALL EJECTOR PIN MARKS TO BE FLUSH TO .005 MAX

44、BELOW SURFACE. 所有的顶针印低于物品表面最大不超过0.005EJECTOR PIN LOCATIONS TO BE APPROVED BY INTUITIVE SURGICAL.顶针位置要经过外观工程同意确认5. GATING VESTIGE TO EXTEND NO MORE THAN .020 FROM SURFACE OF PART. 水口残留最大不能超过部品表面0.020GATE LOCATION TO BE APPROVED BY INTUITIVE SURGICAL.水口位置要经过外观工程同意确认6. DRAFT AS SPECIFIED IN THE 3D CAD

45、MODEL.拔模斜度见3D CAD 模型7. PARTING LINE MISMATCH TO BE .004 MAXIMUM.分型线段差最大不超过0.004.8. PARTS TO BE CLEAN WITH NO CONTAMINATION, MOLD RELEASE OR OIL/LUBRICANT.部品要干净，没有污染物,脱模剂，油污或润滑剂NO VISIBLE PARTICULATE OR CONTAMINATION ON PARTS WHEN EXAMINED WITHOUT MAGNIFICATION.用肉眼检查，不能有可见微粒或者污染物9. NO CRACKS, SINKS O

46、R KNIT LINES PERMITTED. 不能有裂纹，披峰，缩水，熔接线VISUALLY INSPECT FOR COMPLETE FILL AND IRREGULARITIES.肉眼检查一下打满胶的部品和其他不良10. NO FLASH GREATER THAN .005 INCHES. 披峰最大不能超过0.005英寸NO LOOSE FLASH PERMITTED.不允许有松散的披峰11. PROVIDE PLASTIC AND INK RAW MATERIAL LOT CERTIFICATIONS WITH EACH SHIPMENT, INCLUDING: SUPPLIER NA

47、ME, LOT NUMBER AND MATERIAL TYPE OR SPECIFICATION NUMBER.每一次交付提供塑料及油墨原材料批号认证，包括供应商名称，批次号，材料类型或者规格编号PACKAGE CERTIFICATION(S) SEPARATE FROM ANY INVOICE PAPERWORK AND INCLUDE IN THE FIRST SHIPPING CARTON.包装认证独立于任何发票文件，包括在第一次纸箱交付12. PROVIDE CERTIFICATE OF COMPLIANCE WITH EACH SHIPMENT INCLUDING SUPPLIER

48、 NAME, SUPPLIER LOT IDENTIFICATION, INTUITIVES PART NUMBER, REVISION, PURCHASE ORDER NUMBER, QUANTITY, SIGNATURE AND TITLE OF SIGNEE, 提供每一次交付的合格证明，包括：供应商名称，供应商批次证明，直观的部品番号，修订版本号，采购订单号，数量，签名及签署者的头衔 AND THE FOLLOWING (OR AN EQUIVALENT) STATEMENT “I CERTIFY THAT THE PARTS IN THIS SHIPMENT WERE MANUFACT

49、URED IN CONFORMITY WITH THE REQUIREMENTS IN THE PART DRAWING AND PURCHASE ORDER FOR THE REFERENCED PART.”并且下述（一个类似的）声明“我保证这批货制造符合部品图纸及相应部品采购订单要求”13. PROVIDE RoHS CERTIFICATE OF COMPLIANCE WITH EACH SHIPMENT. 提供每个装运RoHS证书14. APPROXIMATE PART VOLUME: 2.15 CUBIC INCHES (REF). 部品近似体积：2.15立方英寸15. -DFT IN

50、DICATES A DIMENSION THAT IS DECREASING IN VALUE DUE TO DRAFT ON THE PART. - DFT ： 表示体积的减小是由于部品的拔模处理 +DFT INDICATES A DIMENSION THAT IS INCREASING IN VALUE DUE TO DRAFT ON THE PART.+ DFT ： 表示体积的增加是由于部品的拔模处理16. PACKAGE PARTS IN DOUBLE BAGS AND SEAL BOTH BAGS.部品包装在两个袋子并且袋子都要密封 LABEL OUTER BULK BAGS WIT

51、H INTUITIVES PART NUMBER, REVISION LEVEL, PURCHASE ORDER NUMBER, QUANTITY, AND SUPPLIER LOT NUMBER.包装袋标签上要有：直观的产品番号，修订版本，采购订单号，数量，供应商批次号ISI IQC TO APPLY LABEL “CLEAN ROOM PARTS” OR EQUIVALENT TO BAG.ISI 的IQC 将“打扫房间部品”或相应的标识应用于标签17. VISUALLY INSPECT ALL PRINTING FOR CORRECT ART, LOCATION, SCALE, CLAR

52、ITY ANDCOMPLETENESS视觉检查所有正确图文的印刷、位置、大小、清晰度和完整性18 . TRUE POSITION MAY BE VERIFIED WITH ISI FIXTURE -01 IN LIEU OF MEASUREMENT位置度可以与ISI夹具验证 - 01通用测量-02-B1. MATERIAL : SEE DRAWING TABULATION. 材料：参见图纸标题栏NO REGRIND OR RECYCLED MATERIAL PERMITTED.不允许有水口料或者再回收的材料2. SURFACE FINISH:表面处理：A. INDICATED SURFACES

53、: MOLDTECH MT-11010 OR EQUIVALENTA. 图示表面：MOLDTECH MT-11010 或者类似处理B. ALL OTHER SURFACES: SPI C-1B .其他表面：SPI C-13. ALL EJECTOR PIN MARKS TO BE FLUSH TO .010 MAX BELOW SURFACE. 所有的顶针印低于物品表面最大不超过0.010EJECTOR PIN LOCATIONS TO BE APPROVED BY INTUITIVE SURGICAL.所有水口和顶针位置要经过外观工程同意确认4. GATING VESTIGE TO EXTE

54、ND NO MORE THAN .010 FROM SURFACE OF PART. 水口残留最大不能超过部品表面0.010GATE LOCATION TO BE APPROVED BY INTUITIVE SURGICAL.水口置要经过外观工程同意确认5. PARTS TO BE CLEAN WITH NO CONTAMINATION, MOLD RELEASE OR LUBRICANT.部品要干净，没有污染物,脱模剂或润滑剂6. NO VISIBLE PARTICULATE OR CONTAMINATION ON PARTS WHEN EXAMINED WITHOUT MAGNIFICAT

55、ION.肉眼检查时没有可见的微粒或污染物7. NO CRACKS, SINKS OR KNIT LINES PERMITTED. VISUALLY INSPECT FOR COMPLETE FILL AND IRREGULARITIES.不能有裂纹，缩水，熔接线，肉眼检查一下打满胶的部品和其他不良8. NO FLASH GREATER THAN .005 INCHES. NO LOOSE FLASH PERMITTED.披峰最大不能超过0.005英寸. 不允许有松散的披峰9. PARTS TO BE LAYERED IN CARBOARD BOXES WITH BUBBLE FOAM ON TOP AND BOTTOM OF EACH LAYER.部品分层装在纸板箱，每一层的顶部和底部都要有气泡垫LABEL EACH BOX WITH INTUITIVES PART NUMBER, REVISION LEVEL, QUANTITY, SUPPLIER LOT NUMBER, AND PURCHASE ORDER NUMBER.包装箱标签上要有：直观的产品番号，修订版本，数量，供应商批次号，采购订单号10. PROVIDE RAW MATERIAL LOT CERTIFICA