FET测试机使用手册.doc

FET測試機使用簡易手冊1. (第1測) (第2測)螢幕11122122接 Tester接 TesterSillner狀態 需打Marking則laser On 車速100150 維明、冠魁機台均With Tester 1 2 3 4 5 6 7 8 9With Laser2. 步驟 打開FET背後開關 ON (有2個) SCREEN在 C：FET _F3MN24 (連線程式一)TEST NUMBER(OFFLINE = 0ORON LINE = 1 TO 4) = 11 ENTER COMMAND MP TESTER PROGRAM F6M57AP.(Y OR N) = Y ( 或顯示 PROGRAM NAME =F6M57AP.COM )ENTER COMMAND PR RUN FILE = TSPXXX 1 (測試規格範) REM = DATE = ENTER SUBCOMMAND ZENTER COMMAND PL RUN FILE = TSPXXX 1 ENTER SUBCOMMAND SF TEST PROGRAM =TSPXXX 1.TES PRE DATA FILE = TSPXXX 1 . DAT TSPXXX-1 DELETE? ( Y OR N ) = Y PRE DAT FILE = TSPXXX-1 START SERIAL NUMBER = 1 END SERIAL NUMBER = 30000 START SEGMENT = 1 END SEGMENT = 1 REM = DATE = 顯示 “TSPXXX-1 . DAT” SUCCESSFULLY CREATED POST DATA FILE = TSPXXX-1. DAT ENTER SUBCOMMAND LI TEST PROGRAM =TSPXXX 1.TES LIMIT FILE = TSPXXX 1.LIM REM = DATE = STATISTICAL OR DALTA LIMITS ? (S OR D) = S TEST NUMBER = Z ENTER SUBCOMMAND Z ENTER COMMAND MT TEST PROGRAM =TSPXXX 1.TES ( 顯示 TEST PROGRAM TSPXXX 1.TES SUCCESSFULLY LOADED)ENTER COMMAND AT RUN FILE = TSPXXX 1.RUN REM = DATE = ( 顯示TEST PROGRAM”TSPXXX-1.TES”SUCCESSFULLY LOADED ) PRINT RESULTS ? (Y)es , (S)pool, (F)ile , (N)o) = N DISPLAY RESULT ( Y OR N ) = Y SAVE RESULTS ? (Y OR N) = Y S/NTEST#TEST RYPETEST RESULTP/FBIN CONTROL 2 ( Ctrl鍵+ 2 ) 切換到第2區 (注意: 2為右邊鍵盤數字鍵)C：FET F3MN24 TEST NUMBER (OFF LINE = 0ORON LINE = 1 TO 4) = 21 其餘和步驟 一樣，只是將要測試的檔名改為TSPXXX 2即可 NOTE：1. 若有打錯按Ctrl + Z即可跳出，再重新設一次。2. 若要離連線在ENTER COMMAND下按EXIT回到 C:FET_下。3. 若要列印電性數值：在AT指令後有詢問 PRINT RESULTS ? (Y)es , (S)pool, (F)ile , (N)o) = Y 4. 若要列測試條件：在 ENTER COMMAND- DTDISPLAY TEST FROM DISK?(Y OR N)=YTEST PROGRAM=”TSPXXX-1.TES” TSPXXX-2REM= DATE= PRINT TESTS?( (Y)es , (S)pool , (F)ile , (N)o ) = Y5. 若要計數COUNTER 歸零，則在 S/NTEST#TEST RYPETEST RESULTP/FBINKEY：N輸入：1 (則從第一顆開始測試)6. 若要記錄統計良率，則在S/NTEST#TEST RYPETEST RESULTP/FBINKEY：B7. 若要清除前一批記錄，則在S/NTES