化妆品灌装包装生产记录

1、LOTION AND GEL FILLING BATCH PRODUCTION RECORD 化妆品灌装包装生产记录起草/日期DRAFT BY: 审核/日期CHECKED BY:生效日期ISSUE DATE: Page 0 of 4SKU#DESCRIPTION:BATCH#MFG.DATE:批号：生产日期：订单号: 产品名称：LINE#MACHINE#:流水线号: 设备号:灌装、包装生产记录 FILLING AND PACKAGING BATCH PRODUCTION RECORDSUPERVISOR PRE-FILLING REVIEW (CHECK ALL THAT APPL Y)-灌装

2、前主管复核目录 (如被执行，请打钩号)ALL MATERIAL OF PREVIOUS PRODUCTS MUST HA VE BEEN CLEARED AND CLEANED.上批产品所余物料已清除或退料，以防交叉污染。THE FILLING EQUIPMENT AND SURFACE OF LINE MUST BE INTEGRITY AND HAS BEEN CLEANED. THE RESULTS MUST BE RECORDED.灌装设备和流水线表面完整及功能正常，已被清洁消毒并记录。 BEFORE STARTING PRODUCE. THERE MUST HAS STANDARD

3、SAMPLE ON LINE.产品是否有标样。ALL BULK HA VE STAGED, IDENTIFIED AND ARE WITHIN EXPIRA TION DA TE所有半制品及包装材料有标识，准备就绪，确认无误，并在有效期内.ALL EQUIPMENT HAS BEEN CLEANED所有设备按照已被清洁消毒.THE FORMULA HAS BEEN ISSUED AND APPROVED BY THE QUALITY CONTROL DEPARTMENT此生产记录是否由品保部门发放和确认.THE FILLING AND PACKAGING PERSONNEL ASSIGNED

4、TO THIS BATCH HA VE BEEN TRAINED灌装和包装此批产品的配制工是否被适当地培训.PACKAGING SUPERVISION HAS REVIEWED ALL THE REQUIREMENTS WITH THE PERSONNEL ASSIGNED TO FILL AND PACKAGE THIS BATCH包装部门管理人员已确认灌装和包装所需的所有必要条件DATE （日期）:SUPERVISOR （生产主管）MFG.DATE:批号：生产日期：订单号: 产品名称：LINE#MACHINE#:流水线号: 设备号:灌装、包装生产记录 FILLING AND PACKAGI

5、NG BATCH PRODUCTION RECORD工序Working Procedure操作Operati on记录Record操作人/时间Operate by复核人/时间Check by备料Prepare将瓶子和泵头去掉包装，放入洁净的塑料筐中，紫外杀 菌半小时，将要灌装的内料拖到相应的灌装线上，将外 箱标签和塑料袋清洁后拖到包装线上Take off the package of the bottle and pump, put into the clean plastic box, sterilization with UV, and pull all the other compone

6、nts on the packaging line.瓶批号 Bottle Batch No.:泵批号 pump Batch No.: 半制品批号Bulk Batch No.:灌装Fill先将灌装机的灌装量调整到规定值，将灌装机头对准 瓶口进行灌装。然后插入泵头，旋紧并锁口Adjust thefilling quantity, begin to fill, then insert the pump and make it tight and locked.半制品数量Bulk Quantity :kg单瓶灌装量 Per Bottle Qty.:G喷码Sprinkle Code喷码位置是否正确喷码内

7、容是否完整Made in China11Label Batch No.:MFG :收缩膜封口Seal调整吹风机温度，将收缩膜套于泵头进行封口Adjustthe temperature then put the shrink film on the pump and seal firmly.封口机温度设置Temperature：oC口封口是否牢固MFG.DATE:批号：生产日期：订单号: 产品名称：LINE#MACHINE#:流水线号: 设备号:灌装、包装生产记录 FILLING AND PACKAGING BATCH PRODUCTION RECORD装箱En caseme nt按照每6PCS

8、套上塑料袋(袋口朝上)装入一外箱，封好 外箱箱底，贴好外箱标 sealed the bottom. Put every 6 with the plastic bag into the carton and attached the UPC label实际包 装规格 Packaging Specification in Fact :瓶/箱.封箱En velop用透明胶带将外箱两端和中缝封牢，堆码在栈板上。每层32 箱，共 4 层 Seal the outer pack with the adhesive tape on the two side and the middle slot. Then

9、 pile them to the underlay orderly. Each pallet should be placed 4 layers, and each layer with 32cartons.口 外箱是否按“工字型”封箱栈板堆放是否正确产率计算 YIELD RECONCILIATION灌装Filli ng总数 Total瓶 bottle，半制品损耗量 Bulk waste quantity.Kg. QA 取样量 Sampling Quantity灌装得率 Filling yield%( > 96.0%)， 计算人 calculate by:复核 check by:.包装Packagi ng包装规格 Packaging sp