耐热型乙烯酯树脂玻璃鳞片涂料.doc

Intended Uses用途适用于涂装有高温要求的部位（原烟道，旁烟道，GGH等），也适用于保护长期接触化学物质或其他液体介质的地方，具有更高的耐温性能。（200）Suited for painting the area which needs heat-resistant,protection such as flue pipes,chimney, GGH etc, it is suited for anti-corrosive protecting the area which is close to chemicals or other liquids too, about the details, This paint possesses higher-temperature resistant property (200)ProductInformation产品简介乙烯酯树脂鳞片面层涂料，包含专用耐热酚醛型乙烯酯树脂为主要成膜基料，加入加入20目到800目片径的粗玻璃鳞片、颜填料、活性稀释剂、消泡、分散、抗流挂等助剂，施工时按照一定比例加入乙（固化剂）、丙（促进剂）组份，混合均匀。极佳的硬度和耐磨性能；柔韧性、耐温变和抗疲劳特性、附着良好。抗介质渗透力及强。抗化学介质，耐常见化学品腐蚀。This paint contains specially heat-resistant phenolic-modified vinyl ester and glass flake(20-80D),pigments, activity thinner foamtrol, dispersion agent etc assistants. Before application, please add component Band C into componet A, stir it thoroughly till to homogenous.Excellent hardness and abrasive-resistant propertyExcellent flexibility,temperature change-resistance and durability, adhesion to substrate.Seepage-resistant property is excellent.Stable to chemical, anti-corrosive to usual chemicals.Application details产品数据Volume Solids 固体份96%Colour 颜色 Limited colors，r any color according to Custome,srequests有限颜色，也可按照客户要求调配颜色Dry Flm Thickness干膜厚度800-1000microns 800-1000微米Theoretical Coverage 理论涂布率0.7m2 /Kg 0.7平方米/公斤Practical Coverage 实际涂布率Allow appropriate loss 允许适量损耗Storage and Handling施工详述 Allow appropiate A:B:C=20:0.3:0.2(by weight )甲：乙： =20:03:0.2（重量比）During mixing and Using ,be sure that it is free from foreign substances 混合和使用过程中应避免混入水等杂质Induction Time 熟化时间Not necessary 不需要熟化Method of Application施工方法Recommended: blade coating 推荐采用：刮涂Pot Life 使用期15：60min; 25:40min; 35:15minWe can adjust the pot life and drying time according the temperature.我公司可应客户要求根据涂装环境温度调整使期和涂膜干燥时间After mix ,please use up it during the Valid time, or it is wasted.涂料混合后，宜在使用期内用完，过期不能使用tThinner 稀释剂C015，According to the method of application and viscosity Thinner should be added after components A and B were stirred till to homogenous. If there is no C015, acetone may substitute for it.稀释剂加入量视施工方式及所需施工粘度而定，稀释剂应在甲乙组份混合后添加，没有专用稀释剂时也可用丙酮代替Clear 油漆设备清洗The tools shoulded be cleaned immediatedly with afterapplication , or it is difficult to clean them 清洗工作应及时，涂料完全固化后，清洗工作将变得困难。Drying time and Over coating Interval干燥时间覆涂时间SubstrateTemperature底材温度Touch Dry表干（H）Hard Dry硬干（H）Completely Cure完全固化（d）Over coating Interval推荐覆涂间隔Mix最短Max最长1525358428428428 hour 小时4 hour 小时2 hour 小时8 hour 小时4 hour 小时2 hour 小时 耐热型乙烯酯树脂玻璃鳞片涂料200 Storageand Handling贮存与管理Storage 贮存 Store in cool and dry conditions, keep in close Containers贮存于阴凉干燥处,保持密封Store Life 贮存期 More than six months 至少6个月。A:20Kg in 20 liter container 甲：20公斤于20公升桶中Pack size 包装规格 B:0.3Kg in a little bottle 乙：0.3公斤装于一小瓶中 c:0.2Kg in a little bottle 丙：0.2公斤装于一小瓶中Flash Point 闪点 32Specific Gravity 比重 1.40Kg/L 1.40公斤/公升 Specification and Surface preparation技术要求及表面处理The surface of primer should be clean and dry, the temperature should be above 3than the dew point.The preceding coat:SPE902-P Vinyl ester primerThe subsequent coat SEP902-F vinyl ester finish底漆表面需保持清洁干燥，表面温度高于露点3以上前道配套涂料： SPE904-P乙烯酯树脂底漆后道配套涂料： SEP904乙烯酯树脂面漆 Limitations限制The painting condition: the temperature during application should be between 10and 40, and it should be above 3than the dew point, enough ventilation is necessary at the site scene of application.涂装环境条件：施工环境温度应在10-40，底材表面温度应高于露点3以上，施工场所应保持良好的通风。Notes:”The drying times is decided accoording to the temperature of substrate, the thickness of film and ventilation We can adjust to the drying time according to the temperature . If the film need be repaired, the overcoating interval time should be prolonged in order to be convenient for polishing.During the maximum overcoating interval recommended, the adhesion property is good if longer than it , pleasescrath the surface to be applied to obtain proper coarseness注：固化时间取决于底材温度，膜厚及通风状况，我公司可应客户要求根据涂装环境温度调整涂膜干燥时间，如涂膜表面漆病需要打磨修补，覆涂间隔可能需要延长以利于打磨。在推荐最长覆涂间隔时间内覆涂，可获得最佳的层间附着。超过最长覆涂时间，对漆膜表面进行打磨增加粗糙度处理（如砂纸打磨）也是增进层间附着的有效手段。 Safety Precautions 安全措施This product should be used in painting area by perfessional operators. When painting , please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.This product is a kind of solvent-based paint .Inorder to avoid danger or accident, minimal safety precautions,as follow , should be down .The paint contains volatile solvent and is flammable . So must keep away from sparks and open flames.No smoking at applacation site ,Effective precautions (such as using explosion-proof electrical equipments. No static electricity accumulation or metal collision etc) also should be done so as to avoid producting sparks .Flash point of paint , mentioned above on product Data sheet, is the lowest temperature at which mixture of the volatile materails of paint can ignite or explode with air. Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general, Therefore, 200m3 of ventilation quantuty per 1Kg solvent (according to the solvent ) is necessary.Product skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves,eye protection, face masks barrier cream and so on ). Kif paint gets in touch with skin , wass fully with large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately. Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation.Handle empty containers with care and do not bring about environmental contamination.NOTICE: If consumers have not taken effective safe