游泳池涂料的特点和施工.doc

Intended Uses用途可用于铁制或混凝土制的游泳池，蓄水池（非饮用水）的涂装，可防止渗水，可防止腐蚀或风化，耐水浸泡和干湿交替、还可防止藻类生长。Suited for painting swimming pool and water tank made with steel or concretes. The coat and prevent is Seeping. Corroding and weathering with water soaking and humid-dry cycling resistance even avoid algae growing. ProductInformation产品简介Various 各色Application details产品数据Volume Solids 固体份40-50% According to the color40-50% 与颜色有关Dry Flm Thickness干膜厚度50-60microns 50-60微米Theoretical Coverage 理论涂布率5.6-7.1m2 /Kg According to the color and D.F.T 7.9平方米/公斤 视干膜和颜色而定Practical Coverage 实际涂布率Allow appropriate loss 允许适量损耗Storage and Handling施工详述Mix Radio 混合比One packgae 单组份Method of Application 施工方法 Airless Spray 无空气喷涂 Recommended 推荐采用 Brush or Roller 涂刷或辊涂 Recommended 推荐采用 Conventional Spray 传统喷涂 Not Recommended 不推荐采用Thinner 稀释剂 C001Cleaner 油漆设备清洗剂 C001Pot Life 使用期 Not limit 无限制Storage 贮存期 One year 一年Drying time 干燥时间 SubstrateTemperature底材温度Touch Dry表干（h） Hard Dry 硬干 (h）Over coating Interval覆涂间隔Min最短Max最长250.5248 hours 小时Not limited无限制 游泳池涂料的特点和施工Storage andHandling贮存与管理Storage 贮存 Store in cool and dry conditions 贮存于阴凉干燥处 Pack size 包装规格 25Kg in 20 liter container 25公斤装于20公升容器中Flash Point 闪点 38 Specific Gravity 比重 1.25-1.35Kg/L 1.25-1.35公斤/公升 Specification and Surface preparation技术要求及表面处理The steel surface to be applied: Blast to Swedish Standard Sa2.5 or rust-removed manually or with power tool to St3. Then paint primer. The surface should be clean and dry.The concrete surface: Must cured completely. The surface should be clean and dry钢材表面：喷砂除锈至瑞典标准Sa2.5级或手工或动力工具除锈至St3, 然后涂装底漆，表面保持清洁干燥。混凝土：充分熟化，表面清洁干燥。 Safety Precautions 安全措施This product should be used in painting area by professional operators. When painting , please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.This product is a kind of solvent-based paint .In order to avoid danger or accident, minimal safety precautions, as follow, should be done.The paint contains volatile solvent and is flammable . So must keep away from sparks and open flames. No smoking at application site, Effective precautions (such as using explosion-proof electrical equipments. No static electricity accumulation or metal collision etc) also should be done so as to avoid product sparks .Flash point of paint, mentioned above on product Data sheet, is the lowest temperature at which mixture of the volatile materials of paint can ignite or explode with air. Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general, Therefore, 200m3 of ventilation quantity per 1Kg solvent (according to the solvent ) is necessary.Product skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves, eye protection, face masks barrier cream and so on ). If paint gets in touch with skin , was fully with large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately. Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation.Handle empty containers with care and do not bring about environmental contamination.NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), our company will NOT be responsible for any accident. 本产品由专业人缘在工业场所使用,使用时请参照本说明书及健康安全手册,如客户在使用本产品前,未能仔细了解有关产品的健康安全知识,请与本公司联系.该涂料为溶剂型涂料,为避免事故或危险发生,应采取最低限度的安全措施如下:此涂料为易燃物,并含有挥发性易燃溶剂,故必须远离火星和明火,严禁在作业场所吸烟,并采取有效措施,防止火星产生(如采用防爆电器设备,杜绝静电积累,避免金属撞击等)本产品说明书中所列涂料及溶剂的闪点是引起燃烧的最低温度. 施工场所应尽量进行通风良好,为消除使用过程中的爆炸隐患,应保证足够的通风量以维持气体/空气比例不超过最低爆炸极限的10%,通常每千克溶剂需要200立方米通风量,(与溶剂种类相关)就能维持最低爆炸极限10%的工作环境.采取有效措施以防止皮肤和眼睛与涂料接触(如使用工作服,手套