修整泥浆接附件工艺.doc

修整泥浆接附件工艺泥浆的调制：泥浆的浓度1.9，有时会跟据产品的造型而定，但粘度要强，流动性要好，沉浮期至上24小时以上，所加调节剂不得超过0.3%，醋0.2%，牛皮胶0.25%，麦芽糖0.3%；五；修整在平时操作过程中，最容易出现的问题，有以下几点：Modulation of mud, mud density 1.9, sometimes according to the shape of the product, but the viscosity, liquidity, and phase of the first 24 hours, the regulator shall not exceed 0.3%, vinegar 0.2%, cattle hide glue 0.25%, malt sugar 0.3%; Five; Nap during normal operation, the most easy to appear problem, there are the following: A、接附件干湿度要一致，不然干白后会完全脱离开裂； B、孔心的附件，须留出气孔，因为物体气体受热后会膨胀，同样在有限空间内活动，气体向外排挤，故产品会发生爆炸； C、割口，未定型产品不可挖，会变形，跟据不同的产品，选用适当的工具，跟据不同的形状，打不同的刀型，刀片必须锋利不然会丝丝开裂，割口处不可挖尖角，易从尖角处拉裂，割完口后要扫浆水，防止开裂； D、修整：平面的产品，注意冲点，如冲点不洗散，会造成不吸色或不吸釉，冲点的处理：热水加醋； E、修产品：水不可打的太多，否则会气泡，产品上的颗粒，水纹线、石膏点要处理掉，纹路需清洗自然； F、接附件处要处理与整体相连之处，清浆时胚体不可太干；捏花：A, attachment dry humidity should agree, otherwise after dry completely from cracking; B and hole heart attachments, you must leave air flow, gas after heated objects could cause inflation, the same activity within the limited space, the gas to the outside, so the products will be an explosion; C, cut the mouth, did not finalize the design product not dig, deformation, according to different products, choose the appropriate tools, according to different shape, playing a different type knife, the blade must be sharp or youll filar silk craze, cut the mouth not dig Angle, easy cracking, from the Angle after cutting the hole to sweep water, prevent cracking; D, dressing: flat products, pay attention to the point, as the impact point not to wash, can lead to no color or absorption does not attract glaze, blunt point processing: hot water and vinegar; E, products: water not dozen is too much, or you will air bubbles and particles on the products, water lines, gypsum point to dispose of, need clean natural grain; F, attachment to place are connected to the whole process, clear a plasma body not too dry; Pinch flower: 流程；1、压制泥土片，2、划片状，3、接捏花，4、比对样品注意事项： 1泥土必须经练泥机抽真空提练2次后才能使用； 2酿酒设备工作台面需保持干净，免杂物渗入泥土内影响品质； 3根据土的收缩比例确定形状大小； 4方向一定要正确； 5捏小花时泥土要湿软，大花时泥土稍平一点，但不可定型； 6捏花须带医用手指套，防止指纹；Process; 1, suppress soil slice, 2, flake, 3, kneading, note 4, and the control samples: 1 the soil must be laid on machine vacuum refine twice before use; 2 work surfaces should be clean and free of debris impact quality inside through the earth; 3 according to the size of contraction percentage to determine the shape of soil; 4 direction must be correct; 5 pinch flower mud to wet soft, big flower soil slightly flatter position, but not finalize the design; Six knead stamen with medical finger sets, prevent fingerprints; 修整课总注意事项： 1、指甲不可超过指度； 2、回收土要据不同的土质区分开； 3、中途修不同土质的产品，需换水并清洗工具；比对样品 4、拿产品，大件要双手拿，不可抓接附件较脆弱处，口部也不可拿；窑部工艺流程解析一、简单介绍吊车几种窑炉 1、隧道窑：连续性作业，容量较大； 2、方窑（梭子窑）：间歇式作业； 3、电窑：连续式作业，容量较小，适合烤金烤色； 4、试验窑：间歇式作业，容量小，但使用比较灵活；Finishing class always note: 1, nails shall not exceed index; 2, the recovery of soil to distinguish according to different soil; 3, midway through different soil products, need to change water and cleaning tools; Control samples 4, take products, big want to both hands, do not grasp the attachment is relatively fragile, the mouth or take; Kiln process parse a, simple to introduce our factory several kiln, tunnel kiln 1: continuity, capacity is bigger; 2, the kiln, shuttle kiln: intermittent operation; 3, elec