样品评估报告.doc

样品评估报告 sample evaluation report 开发案号project no：项目名称: 产品名称: project name product name客户代码: 产品料号: customer code byd sap客户料号: 版次: customer p/n rev样品提供单位:注塑车间喷涂车间装配车间 其他plant: molding painting assembly other样品类型: 素材: 1. 结构 2. 颜色 3. 外观sample type raw part: configuration color appearance 喷涂件:1. 颜色 2.外观 3. 性能painted color cosmetic performance 组件: 1. 结构 2.外观 3. 性能 assembly configuration appearance performance 丝印件 颜色 2.性能 3. 外观silk-screen color performance appearance 其 他other：_评估报告编号: report no:模(治)具编号：_产品图纸版次：_mold(mask) no. product drawing rev.模穴号: 1 2 3 4 5 mold cavity no:评估次数： 1 st 2 nd _no. of times检验记录：_ 试模记录：_i.r. no. t.r.r. no. 新 品 新开发厂商 first article new suppliers 修 正 品 其 他：_ modified other样品编号: 客户承认样品编号: sample no: customer approval sample no:结 果(result)： 完全认可 fully approved(此样品可以用于指导开始大批量生产. this sample can be used to guide mass production) 如有疑议者, 请于三日内向原评估单位提出。若无异议, 本单据将为制定检验规范的依据。 in case of doubt, please submit your comment to the original evaluation dept. within 3 days. should there be no comment, this evaluation shall be the basis for inspection specification and mold coming into stock. 条件认可 conditional approval限 时 (time limit / deadline)_/_/_(此样品可以指导在某个时间段内的生产,完成后需要重新评估, this sample can be used to guide production in any intervals, it must be re-evaluation after completed) 限 量 (quantity limitation) _ pcs.(此样品只能用来指导一定量的产品生产,生产完成后需要重新评估.this sample can be used to guide some quantity of production, it must be re-evaluation after completed) 不合格 disqualified 请于_日内再送样品，若无法改善，请与 项目单位 计划单位 制造单位联系，商量解决措施，否则超过期限，视同放弃供应权论。 please resubmit your sample within _ days. should improvement not be possible, please contact following dept. to work out solution, otherwise it will be regarded as waiver for the right to supply, if solution could not be provided within the time limit. design dept. production planning dept. manufacture engineering dept. 模具评估合格,可以用于正常生产 mold is ok and can be used in mass-production评估目的(evaluation purpose)： 按客户的检验标准和品质的sip及图纸对素材的尺寸结构进行评估(客户已签样板) evaluate raw part dimension and configuration accordance with customer inspection standard and quality sip (customer have signed standard sample) 按客户的检验标准和品质的sip对喷涂件进行外观和性能检验(客户已签样板) evaluate painting part cosmetic and performance accordance with customer inspection standard and quality sip (customer have signed standard sample) 按客户的检验标准和品质的sip对丝印件进行外观和性能检验(客户已签样板) evaluate silk-screen printing part cosmetic and performance accordance with customer inspection standard and quality sip (customer have signed standard sample) 按客户的检验标准和品质的sip对组件进行外观和性能检验(客户已签样板) evaluate sub-assembly cosmetic and performance accordance with customer inspection standard and quality sip (customer have signed standard sample) 通过评估产品的结构性能来评估模具的结构和性能 evaluate tooling performance and configuration accordance with evaluating product configuration and performance. 附件清单(attachment list): fai 编号(report no): 测试报告 (test report) 编号(report no): 色差分析报告(color difference report) 编号(report no): 检验报告(inspection report) 编号(report no):评估单位:_tel: 拟 订：_qe确 认：_me确认_ 审 核：_department: tel: initiator checked checked approved评估报告和样品分发单位: 计划 项目 品管 品质工程 注塑车间 喷涂车间 其他此评估报告传递流程：项目工程师填写内容和编制（附上样品相关的测试报告） me和qe确认 项目主管审核 项目工程师比亚迪股份有限公司 存 样品评估报告 sample evaluation report 开发案号project no： 1.关键尺寸(key dimension)no.尺寸号location检验项次i.r.item图 面 规 格drawing spec.实 测 尺 寸inspect dim.允 收 状 况acceptable status2. 外观：(outward appearance)说明：(explain) accepted rejected附测试报告 -3. 制造性：(manufacture)a. 成型性(molding) accepted rejectedb. 冲制性(stamping) accepted reje