凤凰20112012通过USB数据线强刷教程.doc

凤凰2011/2012通过USB数据线强刷教程注意：1.不管最高版本的资料是否有中文，只要机器无法开机，必须强刷最高版本的资料，否则强刷无法成功；2.S40非智能机机型强刷成功后需要按照楼上的方法在开机状态下重新刷一遍，否则丢失证书；1.打开凤凰，并且打开电脑的设备管理器，连接手机至电脑，不插手机电池2.保持NO CONNECTION首位，点击“File” - “Open Product”下载 (19.03 KB)2011-4-6 17:413.选择死机的工厂代码（RM-xxx），一般从电池仓内的标签里可以寻找到下载 (25.23 KB)2011-4-6 17:414.点击“Flashing” - “Firmware Update”下载 (18.23 KB)2011-4-6 17:415.点击旁边的“.”进行CODE的选择，选择有中文的CODE，一般（S60机型：APAC1、Singapore、Malaysia）（S40机型：APAC-X、APAC-R）地区的CODE都有中文，选好点击OK，如果最高版本资料没有中文，就随便选个，确保是最高版本下载 (29.43 KB)2011-4-6 17:41下载 (57.3 KB)2011-4-6 17:416.勾选“Dead phone USB Flashing”，点击“SW Reset”开始强刷下载 (31.19 KB)2011-4-6 17:417.等到出现如下提示，点击确定后插上电池，按开机键3秒松手，此时可以听到电脑有叮咚的声音，说明检测到新驱动（N97等机型无需按开机键，只要插上电池，即可被检测到），如果过了10秒钟设备管理器不出现下图2个驱动，请直接拔了电池再插上电池，按开机键3秒松手，直到出现2个USB驱动为止下载 (31.53 KB)2011-4-6 17:412个USB驱动图例8.强刷正常进行，中途设备管理器里的2个USB驱动会转换为2个ADL驱动，如下图（N96不会变为2个ADL，永远是2个USB）下载 (31.42 KB)2011-4-6 17:419.点击确定，强刷成功，手机会自动开机，如果没有开机，可以尝试移除电池再插上电池，按开机键完整强刷进度Flashing startedCreating product data items listProduct data items list createdBackup not requiredFlashing phoneInitializingScanning image files.Waiting for USB device.Loading secondary boot code: 15232 bytesSecondary boot loadedLoading update server code: 2884815 bytes Update server loaded Asic CMT: Verifying communication to device. Asic CMT: Verifying communication to device. Asic CMT: Start programming 165230 KB. Asic CMT: Partitioning RM-555_12.0.110_prd.core.C00 Asic CMT: Partitioning area 1. Asic CMT: Erasing RM-555_12.0.110_prd.core.C00 Asic CMT: Erasing area 1. Asic CMT: Erasing area 2. Asic CMT: Erasing area 3. Asic CMT: Erasing area 4. Asic CMT: Erasing partition 0x0000000A. Asic CMT: Erasing RM-555_12.0.110_prd.rofs2.V19 Asic CMT: Erasing area 1. Asic CMT: Erasing RM-555_12.0.110_C01_prd.rofs3.fpsx Asic CMT: Erasing area 1. Asic CMT: Erasing RM555_12.0.110_uda_11_001.uda.fpsx Asic CMT: Erasing area 1. Asic CMT: Erasing rm555ENOA09w24v0.050.fpsx Asic CMT: Erasing area 1. Asic CMT: Programming RM-555_12.0.110_prd.core.C00 Asic CMT: Programming0% Asic CMT: Programming2% Asic CMT: Programming4% Asic CMT: Programming6% Asic CMT: Programming8% Asic CMT: Programming10% Asic CMT: Programming12% Asic CMT: Programming14% Asic CMT: Programming16% Asic CMT: Programming18% Asic CMT: Programming20% Asic CMT: Programming22% Asic CMT: Programming24% Asic CMT: Programming26% Asic CMT: Programming28% Asic CMT: Programming30% Asic CMT: Programming32% Asic CMT: Programming34% Asic CMT: Programming36% Asic CMT: Programming38% Asic CMT: Programming40% Asic CMT: Programming42% Asic CMT: Programming44% Asic CMT: Programming46% Asic CMT: Programming48% Asic CMT: Programming50% Asic CMT: Programming52% Asic CMT: Programming54% Asic CMT: Programming56% Asic CMT: Programming58% Asic CMT: Programming60% Asic CMT: Programming62% Asic CMT: Programming RM-555_12.0.110_prd.rofs2.V19 Asic CMT: Programming64% Asic CMT: Programming66% Asic CMT: Programming68% Asic CMT: Programming70% Asic CMT: Programming72% Asic CMT: Programming74% Asic CMT: Programming76% Asic CMT: Programming78% Asic CMT: Programming80% Asic CMT: Programming82% Asic CMT: Programming84% Asic CMT: Programming RM-555_12.0.110_C01_prd.rofs3.fpsx Asic CMT: Programming RM555_12.0.110_uda_11_001.uda.fpsx Asic CMT: Programming86% Asic CMT: Programming88% Asic CMT: Programming90% Asic CMT: Programming92% Asic CMT: Programming94% Asic CMT: Programming96% Asic CMT: Programming98% Asic CMT: Programming rm555ENOA09w24v0.050.fpsx Asic CMT: Programming100% Asic CMT: Verifying communication to device. Phone flashing completed. Waiting for phone to boot up Bootup successful Verifying communication to product (before flash finalizing) Communication verified Product code changed Doing factorysets Factorysets complete Loading default data to phone Loading default data to phone Getting Data Package Reading product state Starting backup/restore sub-procedure: data item pre-delay data item pre-delay data item pre-delay Sub-procedure completed: Succeeded., result code: 0 Starting to backup/restore data item: ProductProfile, version: 1.1 Data Item backup/restore completed: Succeeded., result code: 0 Starting backup/restore sub-procedure: data item post-delay data item post-delay data item post-delay S