IM153-4 PN IO 的操作系统更新.doc

Service & SupportIM153-4 PN IO 的操作系统更新隐藏订货号显示订货号订货号: 6ES7153-4AA00-0XB0IM153-4 PN IO FOR 12 MODULES S7-300描述： 更新操作系统时，始终应当更新到相关订货号可用的最新版本。以前版本的操作系统版本仅作为备用，允许用户恢复到最初的版本，迄今为止还未发现有这样做的必要。IM153-4 固件的最新版本对该订货号的所有产品版本均有效 。 1. 通过固件更新卡进行更新： 创建固件更新卡的要求： 存储容量为2MB 的微存储卡，订货号 6ES7953-8LL20-0AA0 或4MB 的存储卡，订货号 6ES7953-8LM20-0AA0 或8MB 的存储卡，订货号 6ES7953-8LP20-0AA0 STEP 7 V5.1 + SP2 或更高版本 带有外部 PROM 编程器 6ES7 792-0AA00-0XA0 的 PC 或带有适配器 (6ES7 798-0BA00-0XA0) 的 PG720/740 或FieldPG/PowerPG，用于编程微存储卡通过 STEP7 创建固件更新卡的步骤： 1. 下载所需的固件文件。 2. 双击文件名将文件解压缩。 3. 在 SIMATIC 管理器中执行“File/Delete/S7 Memory Card”命令，删除微存储卡。 4. 在 SIMATIC 管理器中选择“Target system/Update Operating System”编程操作系统。选择目标目录并“Open” (打开) HEADER.UPD 文件，启动编程过程。执行固件更新： 1. 切断 IM153-4 的电源，将更新用的 MMC 插入。 2. 接通 IM 所在机架的电源。 3. IM153-4 将自动识别存有更新文件的 MMC 并启动更新。更新期间，SF 和 BF LED 指示灯将会亮起。 4. 大约 30 秒后操作系统的更新完成，此时 IM153-4 上只有 BF LED 闪烁表示该完成状态。所有其它的 LED 均熄灭。更新完成后切断 IM153-4 的电源并将更新用的 MMC 拔出。要弹出 MMC，用一个小螺丝刀或者一支圆珠笔按下 MMC 插槽下方的弹出开关。2. 通过 STEP7 HW Config 在线更新固件： 1. 下载所需的固件文件。 2. 双击文件名将文件解压缩。 3. 在 HW Config 中选择相应的 ET200M 站 。 4. 在程序菜单中选择下列菜单命令编程固件：“Target System/ Update Firmware”。 5. 在对话框中选定固件文件所在的目录并启动固件下载。下载过程在 IM153-4 上不可见。下载完成后新固件可以自动启动，或者通过电源的 OFF/ON 启动。3. 使用 SIMATIC 管理器在线更新固件： 1. 下载所需的固件文件。 2. 双击文件名将文件解压缩。 3. 将编程设备连接到 ET200M 站所处的线路中 。 4. 在 SIMATIC 管理器中打开“Accessible Nodes”视图并选择站点地址 。 5. 在程序菜单中选择下列菜单命令编程固件：“Target System/PROFIBUS/Update Firmware”。 6. 在对话框中选定固件文件所在的目录并启动固件下载。下载过程在 IM153-4 上不可见。下载完成后新固件可以自动启动，或者通过电源的 OFF/ON 启动。 IM153-4 的订货号和最新版本总览： 订货号固件版本升级.6ES7 153-4AA00-0XB0.V1.0.4升级推荐： V1.0.4 更新描述 1534AA00_V104.EXE ( 815 KB ) .V1.0.0只用于备份： 1534AA00_V100.EXE ( 814 KB ) 更新版本 V1.0.4 (6ES7 153-4AA00-0XB0)固件中修订的内容： 通过了 PROFINET Conformance Class A 认证 Stop 模式下的诊断响应 条目号:26331274日期:2007-11-30Operating System Updates for IM153-4 PN IOHide part numberDisplay part numberPart number: 6ES7153-4AA00-0XB0IM153-4 PN IO FOR 12 MODULES S7-300DESCRIPTION: When updating the operating system, you should always update to the latest version available for the product with the relevant order no. The previous versions of the operating system are intended only as a backup, permitting you to downgrade again to the original version, which however has not been necessary in any known case as yet.The latest version of an IM153-4 firmware is valid for all the releases of that order no. 1. Updating by means of a firmware update card : Requirements for creating a firmware update card: Micro Memory Card with a capacity of2MB, order no. 6ES7953-8LL20-0AA0 or4MB, order no. 6ES7953-8LM20-0AA0 or8MB, order no. 6ES7953-8LP20-0AA0 STEP 7 V5.1 + SP2 or higher PC with external prommer 6ES7 792-0AA00-0XA0 orPG720 / 740 with adapter (6ES7 798-0BA00-0XA0) orFieldPG / PowerPG to program the memory cardProcedure for creating a firmware update card via STEP 7: 1. Download the required firmware file. 2. Unpack the file by double-clicking the file name. 3. Delete the memory card with File /S7 Memory Card/Delete in the SIMATIC Manager. 4. Program the operating system by selecting Target system/Update Operating System in the SIMATIC Manager, select the target directory and Open the HEADER.UPD file to start programming.Executing the firmware update: 1. Power OFF at the power supply for the IM153-4 and insert MMC with the update 2. Power ON at the power supply of the rack in which the IM is located 3. The IM153-4 will automatically identify the MMC with the update files and start the update. During the update the SF and BF LEDs will be lit. 4. The operating system update is completed after about 30 seconds, indicated by the blinking of only the BF LED on the IM153-4. All other LEDs are dark.After the update switch OFF the power to the IM153-4 and remove the MMC with the update. To eject the MMC, use a small screwdriver or a ballpoint pen to press on the ejector in the lower part of the MMC slot.2. On-line firmware update by means of STEP7 HW-Config: 1. Download the required firmware file 2. Unpack the file by double-clicking the file name 3. Select the corresponding ET200M station in HW-Config 4. Program the firmware by selecting: Target System/ Update Firmware in the program menu. 5. Earmark the directory with the firmware file in the dialog box and start the firmware download.The download procedure is not visible on the IM153-4. After the download is completed the new firmware can be started automatically, or by means of power OFF/ON.3. On-line firmware update using the SIMATIC Manager: 1. Download the required firmware file. 2. Unpack the file by double-clicking the file name. 3. Connect the programming device to the line to which the ET200M station is connected. 4. Open the view Accessible Nodes in the Simatic Manager and select the station address. 5. Program the firmware by selecting: Target System/PROFIBUS/Update Firmware 6. Earmark the directory with the firmware file in the dialog box and start the firmware download.The download procedure is not visible on the IM153-4. After the download is completed the new firmware can be started automatically, or by means of power OFF/ON. Overview of order no.s and latest versions of the IM153-4: Order No.Firmware VersionUpgrade by .6ES7 153-4AA00-0XB0.V1.0.4Recommended for upgrading: Update V1.0.4 Description 1534AA00_V104.EXE