HB-T001D对射与卧式主机的学码方式.doc

HB-T001D对射与卧式主机的学码流程How HB-T001D Solar-powered Wireless Active Infrared Detector learn the code with the horizontal host1 按下对射背部开关（按一次即可，发送端、接收端一致）I. Press the switch on the back panel of the detector (the transmitting terminal and the receiving terminal has a switch respectively)2 若开机正常，对射发送端和接收端红外光孔的中间孔灯亮（接收端伴有开机三次继电器跳动）II. If the detector normally starts up, the indicator lamps at middle infrared holes of the transmitting terminal and the receiving terminal of the detector light up (the receiving terminal will dither 3 times when the detector normally starts up) 3 将对射对准，发送端灯亮15秒左右的时间后灯灭，接收端在对准情况下的10秒后灯闪，表示对射已经对准，可以正常工作。（注意：只有当对射进入工作状态后才能正常触发报警）III. The indicator lamp at the transmitting terminal will go out after about 15 seconds; if the indicator lamp at the receiving terminal blinks after 10 seconds, it signifies the transmitting terminal is well aligned with the receiving terminal and the detector is under normal operating mode (Note: An alarm can be triggered when the detector is under operating mode). 4 将配置的天线装入主机天线插口IV. Insert the antenna into the host socket for antenna. 5 按住主机“功能”键的同时使主机通电；效果图如下V. Hold “FUNCTION” key of the host and at the same time keep the host energized. The effect picture is shown as follows: 6 再按一下“功能”键，使主机调整至如下图所示状态，表示主机防区可学码（注意，若有乱码学入，可按“功能”键予以清空防区。VI. Press “FUNCTION” key again to set the host to the mode shown in the figure below, which signifies it is possible for the defense zones of the host to learn codes (Note: if any wrong code is learnt, press “FUNCTION” key to delete defense zones). 7 用厚物完全阻断对射红外光孔，对射有三次继电器跳动，主机若学码成功会有“嘀嘀”音提示并且显示如下图。VII. Completely block up infrared holes of the detector with thick materials, and then the detector relay dithers 3 times. If the host successfully learns the code with the detector, it will give out “BEEP” sound as prompt, and display the following information shown in figure below. 8 若学码结束，可按“复位”键退出学码状态，如下图VIII. If the host has completed learning code, press “RESET” key to exist the code learning mode (See Figure Below)9 拉长主机天线IX. Stretch out the host antenna. 10 用厚物完全阻断对射红外光孔，对射有三次继电器跳动，主机报警（显示报警时间，报警防区），可按“复位”键予以撤防。X. Completely block up infrared holes of the detector with thick materials, and then the detector relay dithers 3 times and the host will give out an alarm (alarm triggered time and defense zone where an alarm is trigged will be displayed ). Press “RESET” key to disarm defense zones. 11 撕去对射太阳能板上的塑料薄膜，以便更好接收光线。XI. Remove the plastic film on the solar panel of the detector so as to get sunshine. 12 测试项目： 无线距离测试：拉长主机天线，确保对射已经学入主机，可进行空旷无线距离测试与实用无 线距离测试（有阻挡物）； 实际安装测试：将对射实际安装在户外，定期触发报警，测试对射工作是否正常。 静态功耗测试：将对射放置在完全无光照环境，可定期触发报警，测试静态待机时间。 XII. Test Items:Wireless distance test: Stretch out the host antenna to ensure the code of host has been learnt by the detector for wireless distance test in open spaces and practical wireless distance test (there is any obstacle).Actual installation test: Install the detector outdoors and routinely trigger an alarm to test if the detector works norma