思科rip详细配置教程.doc

BY: 小福仔 更多教程请进 /492311578配置RIP 时，必须注意IP的规划问题。RIP 不支持可变长子网。RIP 配置命令全局模式下 route rip Network A.B.C.DIP 配置PC0 网关 PC1 网关 R1 配置R1(config)#int s0/0R1(config-if)#no shu%LINK-5-CHANGED: Interface Serial0/0, changed state to downR1(config-if)#ip address R1(config-if)#clock rate 64000R1(config-if)#exitR1(config)#int s0/1R1(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/1, changed state to downR1(config-if)#ip address R1(config-if)#clock rate 64000R1(config)#route ripR1(config-router)#network R1(config-router)#network R2 配置R2(config)#int s0/0R2(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/0, changed state to upR2(config-if)#ip address 192.168.%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up % Invalid input detected at marker.R2(config-if)#ip address R2(config-if)#exitR2(config)#int f0/0R2(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upR2(config-if)#ip address R2(config-if)#exitR2(config)#int s0/0R2(config-if)#no shutdownR2(config-if)#ip address R2(config-if)#exitR2(config)#router ripR2(config-router)#network R2(config-router)#network R3路由配置R3(config)#int s0/1R3(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up R3(config-if)#ip address R3(config-if)#exitR3(config)#int f0/0R3(config-if)#no shu%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upR3(config-if)#ip address R3(config-if)#exitR3(config)#route ripR3(config-router)#network R3(config-router)#network 查看路由表R1R1#show ip routeR /16 120/1 via , 00:00:16, Serial0/0R /16 120/1 via , 00:00:14, Serial0/1C /24 is directly connected, Serial0/0C /24 is directly connected, Serial0/1R2R2#show ip routeC /16 is directly connected, FastEthernet0/0R /16 120/2 via , 00:00:18, Serial0/0C /24 is directly connected, Serial0/0R /24 120/1 via , 00:00:18, Serial0/0R3R3#show ip routeR /16 120/2 via , 00:00:07, Serial0/1C /16 is directly connected, FastEthernet0/0R /24 120/1 via , 00:00:07, Serial0/1C /24 is directly connected, Serial0/1测试PC0 PC1PCping Pinging with 32 bytes of data:Reply from : bytes=32 time=125ms TTL=125Reply from : bytes=32 time=125ms TTL=125Reply from : bytes=32 time=125ms TTL=125Reply from : bytes=32 time=124ms TTL=125Ping statistics for : Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),Approximate round trip times in milli-seconds:Minimum = 124ms, Maximum = 125ms, Average = 124msPC1PC0PCping Pinging with 32 bytes of data:Reply from : bytes=32 time=141ms TTL=125Reply from : bytes=32 time=109ms TTL=125Reply from : bytes=32 time=125ms TTL=125Reply from : bytes=32 time=109ms TTL=125Ping statistics for : Packe