LF-600中英文说明书.doc

深圳市龙福科技有限公司 龙福600TVL全功能OSD菜单RS485控制星光级摄像机LF600TVL StarLight RS485/OSD Multifunction Box Camera使用手册INSTRUCTION MANUAL警告：安装和使用本产品前请仔细阅读本手册Warning：Please read this manual carefully before installation and use!目 录一、安全提示 ：3二、注意事项 ：3三、产品特性 ：3四、产品功能说明：4五、产品连接示意：5六、产品外观尺寸6七、菜单操作：7八、产品参数：91、SAFETY TIPS：102、POINTS FOR ATTENTION：103、CHARACTERISTICS：104、FUNCTION：115、USAGE：126、MENU OPERATION：137、PARAMETERS：158、ID DIP CODE SETTING：16一、安全提示 ：产品必须由有专用经验人员使用安装！非专业人员请勿打开本机器！二、注意事项 ：请勿将本产品置于潮湿或容易被雨淋的地方，请按照本手册说明安装使用。切勿带电安装操作，以免造成产品损坏。请不要自行拆卸及改装摄像机。请按照本手册连接图进行连接使用本产品。请在规定的电源电压、湿度、温度范围内使用本产品。避免将摄像机对准强光或日光。本说明手册的最终解释权归本产品生产厂家。三、产品特性 ：本产品是600TVL高清晰、全功能、超低照度摄像机，采用256点曝光独立运算及256区独立追踪白平衡技术，还原清晰及曝光准确的图像。内置DNR（数字降噪）功能，更好的降低了在夜晚超低照度情况下图像所产生的噪点，摄像机内部带中英文OSD菜单控制，可支持RS485远程调用摄像机菜单选项，使用更方便，特性如下：1/3” SONY SUPER HAD CCD高解析度600TV Lines 超低照度256区曝光独立运算256区白平衡独立追踪白平衡DC12V /AC24V双电源中英文OSD菜单，可通过RS485远程控制，地址设定为0-127自动识别PELCO-D/PELCO-P 协议及波特率（2400/9600）可选 具备移动报警输出及隐私遮蔽功能伽马参数可调整匹配CRT及LCD显示器输出彩色转黑白模式下黑电平功能设置，提升夜间效果双同步方式：内同步/电源同步（相位可调）摄像机快门可调整1/50-1/120000S，更方便现场应用摄像机在电源、视频、通信三级均加入防浪涌措施内置IR-CUT滤光片切换模组（日间还原真实色彩，夜间提高成像效果）C/CS镜头接口后焦可调四、产品功能说明：通电前请仔细检查线缆的连接.控制器或键盘的地址码必须与目标摄像机的地址码一致.枪机地址码可通过阅读摄像机拨码图核实.如果你的键盘支持多种协议,所用协议必须被改为与摄像机协议相匹配的PELCO-D&PELCO-P协议.因为每个键盘操作的方法可能会不同,如果枪机不能被有效的控制,请参考你的键盘说明书操作说明书,并且键盘是基于PELCO协议标准的. 1. OSD菜单控制：2. 摄像机地址0-127范围可设定，波特率（2400/9600）可选；3. 电源、报警指示灯，正常工作时为绿色，当有移动目标时（摄像机移动报警功能打开时有效，具体见菜单MOTION设置项），指示灯变为红色，目标消失则恢复绿色；4. 视频输出端口；5. 电源同步脉宽调整,在电源为AC24V使用此功能时，需在摄像机菜单SYNC选项设置为AUTO时有效；6. 控制输入输出接口：RS485：RS485输入接口； ALARM：报警输出接口，需将摄像机移动报警功能设置为开时有效，具体见菜单MOTION设置项；DC12V/AC24V：电源输入接口； 7. 自动光圈镜头驱动接口2112345677 53 6图1:摄像机背板示意图图2: DC 驱动插座接线线序脚位定义P1DUMP-P2DUMP+P3DRIVE+P4DRIVE-五、产品连接示意：视频线缆监视器RS485控制线缆控制键盘摄像机键盘RS485ARS485+RS485BRS485-键盘、摄像机连接顺序 键盘、多台摄像机RS-485连接方法协议摄像机可自动识别PELCO-D/PELCO-P协议. 波特率2400、9600可选，请在摄像机与键盘第一次通信时，随意设置键盘发出一条指令，以便摄像机判断当前键盘所设定的协议标准。地址摄像机背部拨码开关设定，地址为0-127号可设定，请在设定完地址后，将摄像机电源断开重新接通一次。调用或退出OSD菜单Call+64+Enter Call+95+Enter Call+99+Enter Call+100+EnterOSD菜单上键盘操纵杆上OSD菜单下键盘操纵杆下OSD菜单左键盘操纵杆左OSD菜单右键盘操纵杆右键盘、摄像机通信设定六、产品外观尺寸七、菜单操作：镜头固定光圈镜头亮度值020消闪烁关、开DC镜头DC程度020消闪烁关、开电子快门1/60,1/250,1/700,1/1K,1/1600,1/2500,1/5K,1/7K,1/10K,1/30K,1/60K，1/120K白平衡自动白平衡手动白平衡红色0160蓝色0160键控自动自动增益开程度020关日/夜转换彩色黑白色同步信号关、开外同步自动转换时间115黑电平 关、开图像设定超背光补偿关、低、中、高(室外使用建议开启此功能)降噪关、低、中、高清晰度程度020镜像关、开动态侦测区域编号14区域显示开、关灵敏度124上8126下8126左4191右4191初始化返回隐私遮蔽区域编号14区域显示开、关区域颜色白色、黄色、绿色、蓝色、红色、黑色、灰色上8126下8126左4191右4191初始化返回颜色增益R-Y020B-Y020伽马值0.3/0.45/0.6/0.75初始化返回设置摄像机ID0255ID显示关、开摄像机名称关开上、下、左、右语言英文、中文同步方式内同步、外同步通信协议PELCO-P/D、DEF波特率2400/4800/9600/57600初始化返回初始化退出八、产品参数：型号 NTSC PAL传感器1/3 SONY Super HAD CCD像素768（H）x 494（V）752（H）x 582（V）扫描方式2:1隔行同步方式内同步，电源同步行扫描频率15.734kHz15.625kHz场扫描频率59.94Hz50.00Hz分辨率600TV Lines(彩色)/650TV Lines(黑白,信号增强)视频输出1.0Vp-p/75 视频信噪比54dBMin.( AGC Correct OFF)最低照度0.1 Lux at F1.2 (彩色模式)0.001 Lux at F1.2 (黑白模式)自动增益关/开 可选光圈控制DC驱动自动光圈模式（快门速度1/501/120,000可调）/电子快门电子快门1/601/120,000 秒1/501/120,000 秒白平衡自动白平衡/手动/键控自动 可选伽马值0.3/0.45(CRT监视器)/0.6（LCD监视器）/0.75背光补偿关/低/中/高 可选（室外使用建议开启此功能）移动侦测报警关/开（4个区域可供设置）隐私遮蔽关/开（4个区域可供设置）彩转黑模式自动/彩色/黑白/外部信号输入控制/黑电平开关镜像功能关/水平镜像 可选通信方式RS485通信， PELCO-D/P协议自动适应/波特率（2400/9600）可选控制方式内置OSD菜单镜头接口C/CS接口DC驱动自动光圈镜头供电电源（交流24V / 直流12V）10%功耗2.5W（交流） 2.2W（直流）外形尺寸58(W) X 62(H) X 118(L) mm储存温度-40+60工作温度-10+50湿度范围20%90% RH重量360g1、SAFETY TIPS：u Installation must be operated by qualified professionals！u Laypeople are forbidden to open this camera!2、POINTS FOR ATTENTION： 1. Keep the camera away from damp or rainy places, and install strictly as per the manual.2. To avoid damage, please do not operate with power on.3. Please do not disassemble or make modification on the camera without permission.4. For connection guidance, please refer to the connection diagram in this manual.5. This camera is required to be used under stated voltage/humidity/temperature range.6. Please do not make the camera directly shoot at highlight or sunshine.7. Right of final explanation for this manual is reserved by the manufacturer.3、CHARACTERISTICS：This model is a high definition, full function and super-low illumination camera, it is designed as per the newest 600TVL solution, with built-in DNR function, it can effectively reduce the noise on image displayed under super low illumination at night, and the OSD Menu inside can be remotely controlled through RS485, which makes the camera more convenient to use, characteristics as below:l 1/3” SONY SUPER HAD CCD.l High resolution 600TV Lines super low illumination.l 256 Area independent mathematical exposurel 256 Area independent mathematical auto white balancel DC12V /AC24V Dual power supply.l OSD menu，remote control through RS485，address range 0-127.l Auto recognition on PELCO-D/PELCO-P protocol and its baud rate. l GAMMA adjustable 0.3/0.45(CRT Monitor)/0.6(LCD Monitor)/0.75l Day & Night black level adjustable.l Motion detect output and privacy zone masking function.l External signal control function, it can control camera D/N and IR-CUT switch.l Dual sync. mode：Internal sync./Line Lock（Phase adjustable）l Shutter speed adjustable for the convenience of application.l Take surge-proof measures on power, video and communication.l C/CS Lens Mount Back Focal Length Adjustable1. OSD Menu control：2. Camera Address can be set between 0-127，baud rate (2400/9600) optional.3. Power/Alarm Indicator Lamp，it keeps green under normal working, and turns red when moving objects appears(Valid only when Motion Detect Alarm ON)，and will turn back green when objects disappear；4. Video Output Port；5. Adjust the Power Sync. Pulse width, its valid only when “SYNC” option in camera menu is set as “AUTO” ,if you use this function under AC24V；6. I/O Control Interface：D/N GND ：Input external low voltage to control the D/N switch, it turns to color mode when input low voltage，this function is valid only when “D/N MODE” is set as ”EXT” (Refer to Menu setting)；RS485： RS485 Input Interface； ALARM：Alarm Output Interface，Valid only when “Motion Detect Alarm” is ON，for detail please refer to “MOTION” option in Menu；DC12V/AC24V：Power Supply Input Interface；7. DC Lens Iris Output Connector4、FUNCTION：21 73465 FIGURE1：Camera Rear Panel *Check the connection of cables before power on. *The address of controller or keyborad must accord with that of camera,you can verify the address of box camera by reading the DIP Figure . *If the keyboard you adopt supports multi protocols,it must be altered as PELCO-D & PELCO-P protocol to match with the camera. *Owing to the different usage of various keyboards, if the box camera cant get effective control,please refer to the keyboard user manual,and make sure it adopts PELCO protocol.FIGURE1：Camera Rear Panel FIGURE2：Pin layout for the lens iris output connectorPINDC TYPE LENSESP1DUMP-P2DUMP+P3DRIVE+P4DRIVE-5、USAGE： CAMERA MONITOR RS485 CONTROL CABLE KEYBOARD CAMERAKEYBOARDRS485ARS485+RS485BRS485-CONNECTION ORDER OF KEYBOARD AND CAMERA PROTOCOLThe camera can automatically identify the PELCO-D/PELCO-P Protocol and 2400/4800/9600 baud rate，let the keyboard give an order at its first communication between the camera and keyboard, in order to identify current protocol of keyboard.ADDRESSRear DIP Switch setting，address range from 0 to 255 for setting，power off first and reconnect after address settings done.CALL OR EXIT OSD MENUCall+64+Enter Call+95+Enter Call+99+Enter Call+100+EnterOSD MENU UPJoystick upwardOSD MENU DOWNJoystick downwardOSD MENU LEFTJoystick leftwardOSD MEBU RIGHTJoystick rightwardCommunication Setting of Keyboard and Camera6、MENU OPERATION：LENSESCBRIGHTNESS020FLKOFF/ONDCDC LEVEL020FLKOFF/ONSHUTTER1/60,1/250,1/700,1/1K,1/1600,1/2500,1/5K,1/7K,1/10K,1/30K,1/60K,1/120KWHITE BALATWMANUALRED0160BLUE0160PUSHAGCONLEVEL020OFFDAY/NIGHTCOLORB/WBURSTOFF/ONEXTAUTODWELL TIME115BLACK LEVELOFF/ONIMAGE ADJSBLCOFF/LOW/MIDDLE/HIGH(Outdoor Recommend Open This Function）DNROFF/LOW/MIDDLE/HIGHSHARPNESSLEVEL020H.MIRROROFF/ONMOTIONAREA14DISPLAYON/OFFSENSITIVITY124TOP8126BOTOM8126LEFT4191RIGHT4191INITIALRETURNMASKAREA14DISPLAYON/OFFSENSITIVITY124TOP8126BOTOM8126LEFT4191RIGHT4191INITIALRETURNCOLOR GAINR-Y020B-Y020GAMMA0.3/0.45/0.6/0.75INITIALRETURNGENERALCAM ID0255ID DISPLAYOFF/ONCAM TITLEOFFONUP/DN,LE/RILANGUAGEENG,CHNSYNCINTPROTOCOLP/D,DEFBAUDRATE2400/4800/9600/19200INITIALRETURNINITIALEXIT7、PARAMETERS：Model NTSC PALSensor1/3 “ SONY Super HAD CCD Pixel768（H）x 494（V）752（H）x 582（V）Scanning2:1IntelaceSync. ModeInternal，Line LockHorizontal Frequency15.734kHz15.625 kHzVertical Frequency59.94Hz50.00 HzResolutionColor：600Tv Lines/650Tv Lines（B/W，Signal Enhancement）Video Output1.0Vp-p/75 Video，0.714Vp-p Composite， 0.286Vp-pBurst Level0.286Vp-pS/N Ratio54dBMin.( AGC Correct OFF)Illumination0.1 Lux at F1.2 (Color Mode)0.001 Lux at F1.2 (B/W Mode)AGCON/OFF OptionalIris ControlDC AUTO IRIS（Shutter Speed 1/501/120000）/ELCE-Shutter1/601/60,000 S1/501/60,000 SWhite BalanceATW/AWC/MANUAL ModeGamma0.3/0.45(CRT Monitor)/0.6(LCD Monitor)/0.75Backlight CompensationOFF/LOW/MID/HIGH OutputMotion Detect AlarmON/OFF（4 Areas for setting）Privacy Zone MaskingON/OFF（4 Areas for setting）D/N ModeAUTO/COLOR/B&W/External Signal Control/Black LevelCommunicationRS485， PELCO-D / PELCO-P Protocol Control MannerBuilt- in OSD MenuLens MountC/CS DC Drive LensPower Supply（12VDC/ 24VAC）10%Power Consumption2.5W（AC） 2.2W（DC）Size58(W)X64(H)X135(L) mmStorage Temperature-4060Operation Temperature-1050Humidity Range20%90% RHWeight360g8、ID DIP CODE SETTING：Add12345678Add123456780OFFOFFOFFOFFOFFOFFOFFOFF43ONONOFFONOFFONOFFOFF1ONOFFOFFOFFOFFOFFOFFOFF44OFFOFFONONOFFONOFFOFF2OFFONOFFOFFOFFOFFOFFOFF45ONOFFONONOFFONOFFOFF3ONONOFFOFFOFFOFFOFFOFF46OFFONONONOFFONOFFOFF4OFFOFFONOFFOFFOFFOFFOFF47ONONONONOFFONOFFOFF5ONOFFONOFFOFFOFFOFFOFF48OFFOFFOFFOFFONON OFFOFFOFF6OFFONONOFFOFFOFFOFFOFF49ONOFFOFFOFFONONOFFOFF7ONONONOFFOFFOFFOFFOFF50OFFONOFFOFFONONOFFOFF8OFFOFFOFFONOFFOFFOFFOFF51ONONOFFOFFONONOFFOFF9ONOFFOFFONOFFOFFOFFOFF52OFFOFFONOFFONONOFFOFF10OFFONOFFONOFFOFFOFFOFF53ONOFFONOFFONONOFFOFF11ONONOFFONOFFOFFOFFOFF54OFFOFFONOFFONONOFFOFF12OFFOFFONONOFFOFFOFFOFF55ON OFFONONOFFONONOFFOFF13ONOFFONONOFFOFFOFFOFF56OFFOFFOFFONONONOFFOFF14OFFONONONOFFOFFOFFOFF57OFFOFFOFFONONONOFFOFF15ONONONONOFFOFFOFFOFF58OFFOFFOFFONONONOFFOFF16OFFOFFOFFOFFONOFFOFFOFF59ONONOFFONONONOFFOFF17ONOFFOFFOFFONOFFOFFOFF60OFFOFFONONONONOFFOFF18OFFONOFFOFFONOFFOFFOFF61ONOFFONONONONOFFOFF19ONONOFFOFFONOFFOFFOFF62OFFONONONONONOFFOFF20OFFOFFONOFFONOFFOFFOFF63ONONONONONONOFFOFF21ONOFFONOFFONOFFOFFOFF64OFFOFFOFFOFFOFFOFFONOFF22OFFONONOFFONOFFOFFOFF65ONOFFOFFOFFOFFOFFONOFF23ONONONOFFONOFFOFFOFF66OFFONOFFOFFOFFOFFONOFF24OFFOFFOFFONONOFFOFFOFF67ONONOFFOFFOFFOFFONOFF25ONOFFOFFONONOFFOFFOFF68OFFOFFONOFFOFFOFFONOFF26OFFONOFFONONOFFOFFOFF69ONOFFONOFFOFFOFFONOFF27ONONOFFONONOFFOFFOFF70OFFONONOFFOFFOFFONOFF28OFFOFFONONONOFFOFFOFF71ONONONOFFOFFOFFONOFF29ONOFFONONONOFFOFFOFF72OFFOFFOFFONOFFOFFONOFF30OFFOFFONONONOFFOFFOFF73ONOFFOFFONOFFOFFONOFF31ONONONONONOFFOFFOFF74OFFONOFFON FOFFOFFONOFF32OFFOFFOFFOFFOFFONOFFOFF75ONONOFFONOFFOFFONOFF33ONOFFOFFOFFOFFONOFFOFF76OFFOFFONONOFFOFFONOFF34OFFONOFFOFFOFFONOFFOFF77ONOFFONONOFFOFFONOFF35ONONOFFOFFOFFONOFFOFF78OFFONONONOFFOFFONOFF36OFFOFFONOFFOFFONOFFOFF79ONONONONOFFOFFONO