二次表面处理.doc

Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-01-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.5.28BLOCK/TANK No.分段/舱柜编号102blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()12REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)63DEW POINT ()露点 ()5SURFACE TEMPERATURE()表面温度 ()13SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)38DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-02-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.5.25BLOCK/TANK No.分段/舱柜编号111blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()9REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)76DEW POINT ()露点 ()5SURFACE TEMPERATURE()表面温度 ()10SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)40DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-03-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.27BLOCK/TANK No.分段/舱柜编号112blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()15REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)80DEW POINT ()露点 ()12SURFACE TEMPERATURE()表面温度 ()16SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)36DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-04-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.24BLOCK/TANK No.分段/舱柜编号142blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()12REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)77DEW POINT ()露点 ()6SURFACE TEMPERATURE()表面温度 ()11SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)40DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-05-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.5.25BLOCK/TANK No.分段/舱柜编号143blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()12REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)77DEW POINT ()露点 ()8SURFACE TEMPERATURE()表面温度 ()12SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)39DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-06-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.22BLOCK/TANK No.分段/舱柜编号152blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()12REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)77DEW POINT ()露点 ()6SURFACE TEMPERATURE()表面温度 ()11SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)38DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-07-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.4BLOCK/TANK No.分段/舱柜编号153blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()13REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)49DEW POINT ()露点 ()3SURFACE TEMPERATURE()表面温度 ()15SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)36DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-08-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.22BLOCK/TANK No.分段/舱柜编号181 blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()12REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)68DEW POINT ()露点 ()6SURFACE TEMPERATURE()表面温度 ()14SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)38DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-09-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.7.2BLOCK/TANK No.分段/舱柜编号182/192 blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()25.5REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)81DEW POINT ()露点 ()22SURFACE TEMPERATURE()表面温度 ()26SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)36DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-10-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.25BLOCK/TANK No.分段/舱柜编号191blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()19REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)74DEW POINT ()露点 ()14SURFACE TEMPERATURE()表面温度 ()18SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)40DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-11-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.23BLOCK/TANK No.分段/舱柜编号221/231/222/232blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()10REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)54DEW POINT ()露点 ()1SURFACE TEMPERATURE()表面温度 ()11.2SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)34DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-12-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.28BLOCK/TANK No.分段/舱柜编号223/263/321blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()18REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)73DEW POINT ()露点 ()13SURFACE TEMPERATURE()表面温度 ()18.6SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)36DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-13-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.18BLOCK/TANK No.分段/舱柜编号224/264blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()20REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)82DEW POINT ()露点 ()16SURFACE TEMPERATURE()表面温度 ()21SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)36DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-14-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.13BLOCK/TANK No.分段/舱柜编号225/265/235/275blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()17REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)81DEW POINT ()露点 ()14SURFACE TEMPERATURE()表面温度 ()17.8SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)36DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-15-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.7.10BLOCK/TANK No.分段/舱柜编号226/266/322blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()19REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)65DEW POINT ()露点 ()12SURFACE TEMPERATURE()表面温度 ()23SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)42DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-16-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.6.28BLOCK/TANK No.分段/舱柜编号227/267blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()19REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)58DEW POINT ()露点 ()10SURFACE TEMPERATURE()表面温度 ()20SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)32DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-17-01HULL No.船舶编号57000DWT H2197INSPECTION DATE检查日期2011.7.10BLOCK/TANK No.分段/舱柜编号228/268/323blockCONSTRUCTIONSTAGE 建造分段BLOCK STAGE分段阶段MIDDLE ERECTIONSTAGE 合拢阶段HULL STAGE整体阶段STEEL CONDITION CONFIRM 钢板条件确认TYPE OF DEFECT缺陷类型REPAIR METHOD修补方法REPAIR CONFIRM修补确认DATE日期FREE EDGE自由边GrindingOKREMARKS 备注WELDING BEADS焊道Welding +grindingOKWELD SPATTER焊接飞溅物grindingokSURFACE TREATMENT 表面处理METHOD/GRADE方法/等级sandblastingREMARKS 备注ENVIRONMENT 环境条件DRY TEMPERATURE ()干燥温度 ()18REMARKS 备注RELATIVE HUMIDITY (%)相对湿度 (%)73DEW POINT ()露点 ()13SURFACE TEMPERATURE()表面温度 ()18.6SODIUM CHRORIDE (mg/m2)可溶性盐含量 (mg/m2)36DE-RUSTING GRADE表面处理等级SA2.5SURFACE PROFILES (m)表面粗糙度 (m)MDUST 灰尘I degreeOIL&GREASE油、油脂NOCOATING INSPECTORS NAME：涂层检查员姓名 COATING INSPECTORS SIGNATURE：涂层检查员签名Form SSPCOATING LOG (SECONDARY SURFACE PREPARATION)表 A.2 二次表面处理检查表 （Sheet No.） 编页号：B-18-01HULL No.船