p570物理视图.doc

Subscribe to this information POWER5 information Locations model 561 and 570Map location codes to hardware.Mapping physical location codesNote: The known logical location codes for this unit are listed next to the corresponding physical location in the following information. If you are working with a logical location code for this unit and it is not listed in the following information, contact your next level of support.For address information, see Addresses model 561 and 570.Use the following illustrations to help you map a location code to a position on the server. Figure 1. Front view of the system unit. P4-D1 and P4D2 positions are for a 561. The 570 only has the top slot, the P4D1 location.Figure 2. Back view of the system unitFigure 3. Memory module locations on the processor card (Un-P2-Cx)Use the following illustration to map a node location when you are working with a multiple node installation. All of the nodes have the same location codes inside the system unit; only the serial number is different (Utttt.mmm.sssssss-).Figure 4. Multiple node locations with SMP processor cable shownUse the following illustration to help you identify parts of the control panel.Figure 5. A view of the front of the control panel.NumberNameDescription1DisplayDisplays current status of system startup, or diagnostic information in the event of a hardware problem.2Front serial portPort uses RJ-45 connector. Use to plug in external devices at the front of the system unit.3Increment upScrolls the information in the display up.4EnterEnter5Increment downScrolls the information in the display down.8System reset buttonResets the system9Power LEDBlinking - When connected to the power source (System is in standby mode). Solid - When power button has been pressed. Note: There is approximately a 30-second transition period from the time the power-on button is pressed to when the power LED goes from blinking to on solid. During the transition period, you may observe the blinking intervals speed up.10Power-on buttonTurns the system power on and off.11Service processor reset switch (pinhole)Service Personnel Use12Serial number labelDisplays the system serial numberThe following table contains location codes for the parts that make up the server.Attention: After replacing any part on a server or expansion unit, perform Verifying the repair.Table 1. Physical location codesFailing item nameSymbolic failing item namePhysical location codeIdentify LEDLink to part numberFailing item removal and replacement proceduresSystem unit UnNANAFansFan 1Un-A1YesPart assembly diagramsFanFan 2Un-A2YesPart assembly diagramsFanPower suppliesPower supply 1 PWRSPLYUn-E1YesPower partsPower supplyPower supply 2 PWRSPLYUn-E2YesPower partsPower supplyBackplanesInput/output backplane with embedded: RIO Hub/HSL NIC RIO/HSL link Ethernet controller USB controller (AIX or Linux only) IDE bridge (AIX or Linux only) SCSI controllers (2) Logic oscillatorCLCKMODFRPORTHSL_LNKIOBRDGIO_HUBMA_BRDGMABRCFGMASBUSPPCISYSPRI_PCIPIOCARDSI_PHBSIIOADPSICNTRLSYSBKPLSPBUSSTORIOATOPORTUn-P1Yes28DA 7733 (used only with 2.2 GHz processor )I/O backplaneSCSI controller 1 bus 0Un-P1-T12SCSI controller 1 bus 1Un-P1-T13SCSI controller 2 bus 0Un-P1-T14IDE controllerUn-P1-T15Passthru cardProvides connection for VPD card, system ports, and SPCN25F8I/O backplane assemblyNODEPLUn-P1Yes28DA 7733 (used only with 2.2 GHz processor )I/O backplaneSystem processor backplaneMEMBRDUn-P227AESystem backplaneDisk drive backplaneUn-P3Yes28DBDisk drive enclosureSCSI/IDE cardUn-P3-C1180ASCSI-IDE converter cardMedia drive backplaneUn-P4Yes28DCMedia device enclosurePortssystem port 2 (back of system unit)Un-P1-T1NAsystem port 1 (back of system unit)Un-P1-T2NAS1 system port (front of control panel)Un-P1-T2NARack indicator connectorUn-P1-T3NAIntegrated 2-port USB port 1 (AIX or Linux only)Un-P1-T4NAIntegrated 2-port USB port 2 (AIX or Linux only)Un-P1-T5NAIntegrated dual 1 GB Ethernet controller-port 1Un-P1-T6NAIntegrated dual 1 GB Ethernet controller-port 2Un-P1-T7NARIO/HSL left connectorHSL_LNKHSL2HSL2_xxHSLHHSLH_xxUn-P1-T8YesExternal cablesRIO/HSL cables (concurrent)RIO/HSL right connectorHSL_LNKHSL2HSL2_xxHSLHHSLH_xxUn-P1-T9YesExternal cablesRIO/HSL cables (concurrent)System cable connectorUn-P1-T10NAProcessor and processor regulatorProcessor card 1MEMCTLRANYPROCUn-P2-C1YesProcessor partsSystem processorProcessor card 2MEMCTLRANYPROCUn-P2-C2YesProcessor partsSystem processorSMP processor cableUn-P2-C1-T1 and Un-P2-C2-T1Model 561 and 570 cablesSMP processor cableTemperature sensorUn -P2-C1 and Un -P2-C2Processor partsSystem processorVoltage regulator 1Un-P2-C3YesPower partsVoltage regulator card assemblyVoltage regulator 2Un-P2-C4YesPower partsVoltage regulator card assemblyVoltage regulator 3Un-P2-C5YesPower partsVoltage regulator card assemblyVPD cardUn-P1-T10VPD partsVPD cardService processorService processor cardSVCPROCUn-P1-C8Yes28EAService processor assemblyService processor cableI2CBUSUn-P1-T10Model 561 and 570 cablesService processor cableTime-of-day (TOD)Un -P1-C828EAService processor assemblyTime-of-day BatteryTOD_BATUn-P1-C8-E1Power partsService processor time-of-day batteryHMC 1 connectorUn-P1-C8-T1NAHMC 2 connectorUn-P1-C8-T2NASPCN 0 connectorUn-P1-C8-T3NASPCN 1 connectorUn-P1-C8-T4NAAdaptersPCI adapter in slot 1 PIOCARDMASBUSSLOTERRUn-P1-C1YesSystem partsPCI adapterPCI adapter in slot 2PIOCARDMASBUSSLOTERRUn-P1-C2YesSystem partsPCI adapterPCI adapter in slot 3PIOCARDMASBUSSLOTERRUn-P1-C3YesSystem partsPCI adapterPCI adapter in slot 4PIOCARDMASBUSSLOTERRUn-P1-C4YesSystem partsPCI adapterPCI adapter in slot 5PIOCARDMASBUSSLOTERRUn-P1-C5YesSystem partsPCI adapterPCI adapter in slot 6PIOCARDMASBUSSLOTERRUn-P1-C6YesSystem partsPCI adapterRIO/HSL adapter/InfiniBand host channel adapterink SI_CARDSICNTRLHCAUn-P1-C7YesSystem partsRIO/HSL adapter/InfiniBand host channel adapterRIO/HSL adapter connectorHSL_LNKHSL2HSL2_xxHSLHHSLH_xxUn-P1-C7-T1YesExternal cablesRIO/HSL cables (concurrent)RIO/HSL adapter connector HSL_LNKHSL2HSL2_xxHSLHHSLH_xxUn-P1-C7-T2YesExternal cablesRIO/HSL cables (concurrent)Dual channel SCSI RAID enablement cardUn-P1-C95709RAID enablement cardPCI bridge set 1BRDGSETBRDGST1Un-P128DA 7733 (used only with 2.2 GHz processor )I/O backplanePCI bridge set 2BRDGSETBRDGST2Un-P1Un-P1-C1Un-P1-C2Replace the I/O backplane and cards using the removal and replacement procedures corresponding to the locations indicated.PCI bridge set 3BRDGSETBRDGST3Un-P1Un-P1-C3Un-P1-C4Un-P1-C5Un-P1-C6Replace the I/O backplane and cards using the removal and replacement procedures corresponding to the locations indicated.Memory modulesMemory module 1MEMDIMMUn-P2-C1-C1YesMemory partsMemory moduleMemory module 2MEMDIMMUn-P2-C1-C2YesMemory partsMemory moduleMemory module 3MEMDIMMUn-P2-C1-C3YesMemory partsMemory moduleMemory module 4MEMDIMMUn-P2-C1-C4YesMemory partsMemory moduleMemory module 5MEMDIMMUn-P2-C1-C5YesMemory partsMemory moduleMemory module 6MEMDIMMUn-P2-C1-C6YesMemory partsMemory moduleMemory module 7MEMDIMMUn-P2-C1-C7YesMemory partsMemory moduleMemory module 8MEMDIMMUn-P2-C1-C8YesMemory partsMemory moduleMemory module 1MEMDIMMUn-P2-C2-C1YesMemory partsMemory moduleMemory module 2MEMDIMMUn-P2-C2-C2YesMemory partsMemory moduleMemory module 3MEMDIMMUn-P2-C2-C3YesMemory partsMemory moduleMemory module 4MEMDIMMUn-P2-C2-C4YesMemory partsMemory moduleMemory module 5MEMDIMMUn-P2-C2-C5YesMemory partsMemory moduleMemory module 6MEMDIMMUn-P2-C2-C6YesMemory partsMemory moduleMemory module 7MEMDIMMUn-P2-C2-C7YesMemory partsMemory moduleMemory module 8MEMDIMMUn-P2-C2-C8YesMemory partsMemory moduleNote: First quad of memory modules is plugged into memory module slots P2-Cx-C1, P2-Cx-C3, P2-Cx-C6, and P2-Cx-C8. Second quad of memory modules is plugged into memory module slots P2-Cx-C2, P2-Cx-C4, P2-Cx-C5, and P2-Cx-C7.Device physical locationsDisk drive 1Un-P3-D1 (logical location with RAID card Un-P1-T13-L5-L0, logical location without RAID card Un-P1-T14-L5-L0)YesDisk unit partsDisk driveDisk drive 2Un-P3-D2 (logical location with RAID card Un-P1-T13-L4-L0, logical location without RAID card Un-P1-T14-L4-L0)YesDisk unit partsDisk driveDisk drive 3Un-P3-D3 (logical location with RAID card Un-P1-T13-L3-L0, logical location without RAID card Un-P1-T14-L3-L0)YesDisk unit partsDisk driveDisk drive 4Un-P3-D4 (logical location with RAID card Un-P1-T12-L5-L0, logical location without RAID card Un-P1-T12-L5-L0)YesDisk unit partsDisk driveDisk drive 5Un-P3-D5 (logical location with RAID card Un-P1-T12-L4-L0, logical location without RAID card Un-P1-T12-L4-L0)YesDisk unit partsDisk driveDisk drive 6Un-P3-D6 (logical location with RAID card Un-P1-T12-L3-L0, logical location without RAID card Un-P1-T12-L3-L0)YesDisk unit partsDisk driveIDE drive 1Un-P4-D1YesRemovable media device partsMedia deviceIDE drive 2 for 570Un-P4-D2YesRemovable media device partsMedia deviceControl panelControl panel (bottom media bay)Un -D128D4Control panelServer firmwareServer firmwareUn-Y1Input/output adapter (IOA) assignment rules for i5/OSThe following table provides information necessary to identify the input/output processor (IOP) to which IOAs are assigned. The left column indicates the bridge set in which IOA assignment is allowed. Use the right column to determine the IOP to which an IOA is assigned. The first position in the list must be an IOP. The remaining positions might be IOPs or IOAs. IOAs are assigned to the first IOP located to their left in the list. Although IOAs can be manually reassigned using system service tools (SST)/dedicated service tools (DST), the IOA assignments return to the default order after each initial program load (IPL). Multi-adapter bridge domain / Peripheral Component Interconnect (PCI) bridge set IOA assignment rules Adapters embedded in -P1 planar (no IOP)Embedded SCSI, embedded EthernetC1 - C2Embedded SCSI, C2C3 - C6 C4, C5, C6Parent topic: Finding part locationsSubscribe to this information POWER5 information Addresses model 561 and 570Find part locations using location codes.Use the address to find the location for the 9116-561, 9406-570, and 9117-570 models. Then go to Locations model 561 and 570 to find additional information.Table 1. IOP, IOA, and device address information for the primary unitPhysical location codePossible failing itemDSA (BBBBCcbb) Unit addressIOA and device DSAs do not conform to the following rules if the IOA is manually reassigned after IPL.Un-P1Embedded Ethernet0001-24-00E6FFFFFFUn-P1 (and UN-P1-C9 if RAID enablement card is installed)Embedded SCSI0003-20-002FFFFFFFUn-P1-C1IOP0003-20-00FFFFFFFFUn-P1-C2Communications or Workstation IOA0003-20-00E6FFFFFFUn-P1-C3IOP0002-20-00FFFFFFFFUn-P1-C4Storage IOA0002-20-002FFFFFFFUn-P1-C4Communications or Workstation IOA0002-20-00E2FFFFFFUn-P1-C5IOP0002-24-00FFFFFFFFUn-P1-C5Storage IOA0002-20-004FFFFFFFUn-P1-C5Communications or Workstation IOA0002-20-00E4FFFFFFUn-P1-C6Storage IOAThe IOA has the same DSA as the first IOP found in the following list: C5, C4, C3.6FFFFFFFUn-P1-C6Communications or Workstation IOAThe IOA has the same DSA as the first IOP found in the following list: C5, C4, C3.E6FFFFFFUn-P3-D1Disk unit0003-20-00210200FFUn-P3-D2Disk unit0003-20-00210300FFUn-P3-D3Disk unit0003-20-00210400FFUn-P3-D4Disk unit0003-20-00200200FFUn-P3-D5Disk unit0003-20-00200300FFUn-P3-D6Disk unit0003-20-00200400FFUn-P4-D1IDE drive 1 0003-20-00200600FFUn-P4-D2IDE drive 2 Table 2. IOP, IOA, and device address information for the secondary unitsPhysical location codeP