华为交换机bootromFTP方式升级版本.doc

以MSR5040路由器、FTP/TFTP服务器主机直连为例操作步骤：1 路由器上电自检出现如下的信息：InitDDR.system start booting.Version 2.11Press CTRL+D to stop auto-bootBooting Normal Extended BootRomDecompressing.done!Ensure the baudrate is set to 9600bps!Starting at 0xa00000. * * * * H3C MSR50-40 BOOTROM, Version 2.13 * * * * Copyright(c) 2004-2007 Hangzhou H3C Technologies Co., Ltd. Compiled date: Jul 31 2007, 14:05:28 CPU type : MPC8541 CPU L1 Cache : 32KB CPU L2 Cache : 256KB CPU Clock Speed : 833MHz Memory Type : DDR SDRAM Memory Size : 512MB Memory Speed : 333MHz BootRom Size : 4096KB CPLD Version is 2.00 HardWare Version is 3.00CF Card is Inserted, now is mounting.cf:/ - Volume is OK Mount CF Card OK!CF Card Size:256MBPress Ctrl+B to enter extended boot menu.此时键入，系统将进入BOOTROM菜单。& 说明：必须在出现“Press Ctrl-B to enter Boot Menu.”的3秒钟之内，键入，系统方可进入BOOTROM菜单；否则系统将进入程序解压过程。若进入程序解压过程后再希望进入BOOTROM菜单，则需要重新启动路由器。2进入Bootrom界面用户键入后，系统提示：Please input Bootrom password:此时需要用户要输入BootROM口令（路由器出厂时缺省没有BootROM口令，直接回车即可）。若用户已经修改过BootROM口令，应该输入正确的口令，若三次口令验证未通过，则系统中止。3. 选择以太网口，进行配置升级当用户输入了正确的BootROM口令，系统将出现如下提示信息：=| Boot From CF Card | Enter Serial SubMenu | Enter Ethernet SubMenu | File Control | Modify Bootrom Password | Ignore System Configuration | Boot Rom Operation Menu | Clear Super Password | Device Operation | Reboot |=Enter your choice(1-a):3 选择3进入串口子菜单: Enter Ethernet SubMenu=|Note:the operating device is CF Card | Download Application Program To SDRAM And Run | Update Main Application File | Update Backup Application File | Update Secure Application File | Change Ethernet Parameter | Exit To Main Menu | |=Enter your choice(1-6):5选择5对以太网口进行调整4对FTP参数进行设置以太网口配置菜单：Note: Two protocols for download, tftp & ftp. You can modify the flags following the menu except the boot device. tftp-0x80, ftp-0x0. = clear field; - = go to previous field; Ctrl+D = quitboot device:motfcc1网络下载设备名字，无需更改processor number:0处理器数，无需更改host name:host主机名字，无需更改file name:MSR50-CMW520-R1508P02-SI.BIN与服务器文件一致inet on ethernet (e) :根据实际组网进行设置inet on backplane (b):无需设置host inet (h) :FTP或TFTP服务器的ip地址gateway inet (g) :网关ip地址，根据实际情况设置user (u) :bbxz下载用户名ftp password (pw) (blank = use rsh): 123456下载密码flags (f) :0x0下载标识，FTP为0x0，TFTP为0x80target name (tn) :设置保存在Flas中的目标文件的名称，无需设置startup script (s) :无需设置other (o) :无需设置4下载文件选择2将指定文件下载到CF卡中作为主启动文件=|Note:the operating device is CF Card | Download Application Program To SDRAM And Run | Update Main Application File | Update Backup Application File | Update Secure Application File | Change Ethernet Parameter | Exit To Main Menu | |=Enter your choice(1-6):2boot device : mottsecunit number : 0 processor number : 0 host name : hostfile name : MSR50-CMW520-R1508P02-SI.BINinet on ethernet (e) : host inet (h) : user (u) : guestftp password (pw) : 123456flags (f) : 0x0 Attached TCP/IP interface to mottsec0.Warning: no netmask specified.Attaching network interface lo0. done.Loading.Done!18339940 bytes downloaded.Input the File Name:MSR50-CMW520-R1508P02-SI.BIN/Updating File cf:/msr50-cmw520-r1508p02-si.bin.Update Success!5重启升级（版本更换）下载完毕后重启路由器完成版本升级（更换）操作。【提示】1、MSR 20系列路由器只能使用Ethernet0/0端口，MSR 30及MSR 50系列路由器只能使用GigabitEthernet0/0端口。2、Boo