巴可放映机报警报错信息处理.doc

精品文档巴可放映机报警报错信息处理5003 light sensor - no communication 光线感应器 - 无通讯5004 lamp-no communication 与灯箱无通信 检查灯箱是否装好5005 lamp power supplies, communication failed 与灯电源无通信 检查灯电源线缆是否装好5010 pump refill mode is on 加液模式打开 退出加液模式5011 system running in restricted access mode 系统在警告模式下运行 检查输入抽屉与引擎的接触5020 重新安装一下控制板的类似手机卡的卡片5041 cold mirror fan - speed high 冷镜风扇 转速偏高5042 cold mirror fanspeed too low 冷却镜风扇转速过低 检查冷镜风扇及背板间连线是否接好，是否可以活动5043 cold mirror fanspeed low 冷却镜风扇转速低 同上5050 engine fan - speed too high 引擎风扇转速过高5051 engine fan - speed high 引擎风扇转速偏高5052 engine fan speed too low 引擎风扇转速低 检查引擎风扇是否接好5053 engine fan - speed low 引擎风扇速度低 检查引擎风扇是否接好，是否可以活动5060 heat exchanger fan - speed too high 热交换器风扇转速过高5061 heat exchanger fan - speed high 热交换器风扇转速偏高5062 heat exchange fanspeed too low 热交换器风扇转速过低 检查热交换器上方风扇5063 heat exchange fanspeed low 热交换器风扇转速偏低 同上5070 lamp anode fan - speed too high 灯阳极风扇转速过高5071 lamp anode fan - speed high 灯阳极风扇转速偏高5072 lamp anode fan speed too low 灯阳极风扇转速低检查灯阳极风扇是否接好5073 lamp anode fan speed low 灯阳极风扇转速低检查灯阳极风扇是否接好5080 lamp cathode fan - speed too high 灯阴极风扇转速过高5081 lamp cathode fan - speed high 灯阴极风扇转速偏高5082 lamp cathode fanspeed too low 灯风扇控制速度低 检查风扇接头和FCB5083 lamp cathode fanspeed low 灯阴极风扇转速低 检查灯阴极风扇是否接好5100 smps fan 1 (left side) - speed too high 开关电源风扇1（左侧）转速过高5101 smps fan 1 (left side) - speed high 开关电源风扇1（左侧）转速偏高5102 SMPS fan 1speed too low 开关电源风扇1转速过低 检查两个开关电源风扇5103 SMPS fan 1speed low 开关电源风扇1转速偏低 检查两个开关电源风扇5110 smps fan 2 (right side) - speed too high 开关电源风扇2（右侧）转速过高5111 smps fan 2 (right side) - speed high 开关电源风扇2（右侧）转速过高5112 SMPS fan 2speed too low 开关电源风扇2转速过低 检查两个开关电源风扇5113 SMPS fan 2speed low 开关电源风扇2转速偏低 检查两个开关电源风扇5120 lamp rear fan - speed too high 灯后置风扇转速过高5121 lamp rear fan - speed high 灯后置风扇转速偏高5122 lamp rear fanspeed too low 灯后置风扇转速过低 检查灯后置风扇是否接好5123 lamp rear fanspeed low 灯后置风扇转速偏低 检查灯后置风扇是否接好5132 elca box fanspeed too low 输入通讯单元风扇转速低 检查风扇与导线的连接情况5133 elca box fanspeed low 输入通讯单元风扇转速低 检查风扇与导线的连接情况5140 electronics fan 1 (top side) - speed too high 电子风扇1（顶面）转速过高5141 electronics fan 1 (top side) - speed high 电子风扇1（顶面）转速偏高5142 electronics fan 1 (top side) - speed too low 电子风扇1（顶面）转速过低5143 electronics fan 1 (top side) - speed low 电子风扇1（顶面）转速偏低5150 electronics fan 2 (bottom side) - speed too high 电子风扇2（底部）转速过高5151 electronics fan 2 (bottom side) - speed high 电子风扇2（底部）转速偏高5152 electronics fan 2 (bottom side) - speed too low 电子风扇2（底部）转速过低5153 electronics fan 2 (bottom side) - speed low 电子风扇2（底部）转速偏低5160 engine switchnot OK 引擎安装错误 检查引擎固定螺丝5170 FIBnot connected FIB未连接好 检查FIB确保两个螺丝拧紧5180 lamp housenot connected 灯箱未连接好 检查灯箱上的3个固定螺丝5190 prism switch error 棱镜开关 - 错误5191 prism switchwarning , lens probably touches prism 镜头位移过量 调节镜头5210 pump - speed too high 泵速度过高5211 pump - speed high 泵速度偏高5212 pumpspeed too low 泵速度过低 检查水泵线缆接头接触，SMPS电源板电压;检查泵线缆接头，电源板5213 pumpspeed low 泵速度偏低 检查泵线缆接头，电源板5230 lens zoom positionrequested target not reached 调整或更换镜头 镜头变焦无法达到指定位置5231 lens focus position- requested target not reached 调整或更换镜头 镜头聚焦无法达到指定位置5232 lens horizontal shift position- requested target not reached 检查变焦马达，镜头位置 镜头水平位移未达到指定位置5233 lens vertical shift position- requested target not reached 检查变焦马达，镜头位置镜头垂直位移未达到指定位置5237 lens positionclear requested target time out failed 镜头聚焦未达到指定位置 同52315250 dmd red fan - speed too high 红色通道DMD风扇 转速过高5251 dmd red fan - speed high 红色通道DMD风扇转速偏高5252 dmd red fan - speed too low 红色通道DMD风扇转速太低5253 dmd red fan - speed low 红色通道DMD风扇转速偏低5260 dmd green fan - speed too high 绿色通道DMD风扇转速过高5261 dmd green fan - speed high 绿色通道DMD风扇转速偏高5262 dmd green fan - speed too low 绿色通道DMD风扇转速太低5263 dmd green fan - speed low 绿色通道DMD风扇转速偏低5270 dmd blue fan - speed too high 蓝色通道DMD风扇转速过高5271 dmd blue fan - speed high 蓝色通道DMD风扇转速偏高5272 dmd blue fan - speed too low 蓝色通道DMD风扇转速太低5273 dmd blue fan - speed low 蓝色通道DMD风扇转速偏低5280 ambienttemperature too high 环境温度过高 请改变环境温度5281 ambienttemperature high 环境温度高 请改变环境温度5283 ambienttemperature low 环境温度低 请改变环境温度5284 ambienttemperature sensor open 环境温度传感器开路 检查传感器和导线或更换5285 ambienttemperature sensor short 环境温度传感器短路 检查传感器和导线或更换5290 DMD blue temperature too high 蓝色通道DMD温度过高 检查热交换器的过滤器5291 DMD blue temperature high 蓝色通道DMD温度偏高 检查热交换器的过滤器5293 DMD blue temperature low 蓝色通道DMD温度偏低 光处理器单元没有启动5294 DMD blue temperature sensor open 蓝色通道DMD温度传感器开路 修复导线或更换光处理器单元5295 DMD blue temperature sensor short蓝色通道DMD温度传感器短路 修复导线或更换光处理器单元5300 DMD green temperature too high绿色通道DMD温度过高 更换过滤器5301 DMD green temperature high 绿色通道DMD温度偏高 更换过滤器5303 DMD green temperature low 绿色通道DMD温度偏低 光处理器单元没有启动5304 DMD green temperature sensor open 绿色通道DMD温度传感器开路 检查传感器和导线5305 DMD green temperature sensor short 绿色通道DMD温度传感器短路 检查传感器和导线5310 lamp temperature too high 疝灯温度过高 检查过滤网和抽风5311 lamp temperature high 疝灯温度偏高 检查过滤网和抽风5314 lamptemperature sensor open 疝灯温度传感器开路 检查传感器和导线5315 lamptemperature sensor short 疝灯温度传感器短路 检查传感器和导线5320 FCBforce LPS off 控制板强行关闭疝灯电源 在日志中查找错误信息排除5330 PFC heat-sinktemperature too high 散热器温度过高 检查进气口过滤网5331 PFC heat-sinktemperature high 散热器温度偏高 检查进气口过滤网5332 pfc heatsink - temperature too low PFC散热片 - 温度过低5333 pfc heatsink - temperature low PFC散热片 - 温度偏低5340 DMD red temperature too high 红色通道DMD温度过高 检查滤网，液冷循环5341 DMD red temperature high 红色通道DMD温度偏高 检查滤网，液冷循环5342 dmd red - temperature too low 红色通道DMD温度过低5343 DMD red temperature low 红色通道DMD温度偏低 光处理器单元没有启动5344 DMD red temperature sensor open红色通道DMD温度传感器开路 检查传感器和导线5345 DMD red temperature sensor short红色通道DMD温度传感器短路 检查传感器和导线5350 SMPS primary heat-sink temperature too high 开关电源主散热器温度过高 检查滤网和开关电源5351 SMPS primary heat-sink temperature high 开关电源主散热器温度偏高 检查滤网和开关电源5352 smps primary heatsink - temperature too low 开关电源的主要散热片温度过低5353 smps primary heatsink - temperature low 开关电源的主要散热片温度偏低5360 SMPS secondary heat-sink temperature too high 检查滤网和开关电源 （开关电源次散热器温度过高）5361 SMPS secondary heat-sink temperature high 检查滤网和开关电源 （开关电源次散热器温度偏高）5362 smps secundary heatsink - temperature too low 开关电源次散热器温度过低5363 smps secundary heatsink - temperature low 开关电源次散热器温度偏低5364 SMPS secondary heat-sink temperature sensor open 更换SMPS模块 （开关电源次散热器温度传感器开路）5365 SMPS secondary heat-sink temperature sensor short 更换SMPS模块 （开关电源次散热器温度传感器短路）5370 dmd red fan - voltage too high 红色通道DMD风扇电压过高5371 dmd red fan - voltage high 红色通道DMD风扇电压偏高5372 dmd red fan - voltage too low 红色通道DMD风扇电压过低5373 dmd red fan - voltage low 红色通道DMD风扇电压偏低5380 dmd green fan - voltage too high 绿色通道DMD风扇电压过高5381 dmd green fan - voltage high 绿色通道DMD风扇电压偏高5382 dmd green fan - voltage too low 绿色通道DMD风扇电压过低5383 dmd green fan - voltage low 绿色通道DMD风扇电压偏低5390 dmd blue fan - voltage too high 蓝色通道DMD风扇电压过高5391 dmd blue fan - voltage high 蓝色通道DMD风扇电压偏高5392 dmd blue fan - voltage too low 蓝色通道DMD风扇电压过低5393 dmd blue fan - voltage low 蓝色通道DMD风扇电压偏低5401 +30vvoltage high +30v电压偏高 更换风扇，马达控制板5403 +30vvoltage low +30v电压偏低 检查开关电源和控制板5411 +5vvoltage high +5v电压偏高 更换风扇，马达控制板5413 +5vvoltage low +5v电压偏低 更换风扇，马达控制板5420 tec blue - voltage too high TEC蓝色 - 电压过高5421 tec blue - voltage high TEC蓝色 - 电压偏高5422 tec blue - voltage too low TEC蓝色 - 电压过低5423 tec blue - voltage low TEC蓝色 - 电压偏低5430 cold mirror fan - voltage too high 冷镜风扇 - 电压过高5431 cold mirror fanvoltage high 冷镜风扇电压偏高 更换风扇，马达控制板5432 cold mirror fanvoltage too low 冷镜风扇电压过低 更换风扇，马达控制板5433 cold mirror fanvoltage low 冷镜风扇电压偏低 更换风扇，马达控制板5441 engine fan voltage high 引擎风扇电压偏高 更换风扇，马达控制板5442 engine fan voltage too low 引擎风扇电压过低 更换风扇，马达控制板5443 engine fan voltage low 引擎风扇电压偏低 更换风扇，马达控制板5450 heat exchanger fan - voltage too high 热交换器风扇电压过高5451 heat exchange fan voltage high 热交换器风扇电压偏高 更换风扇，马达控制板5452 heat exchange fan voltage too low 热交换器风扇电压过低 更换风扇，马达控制板5453 heat exchange fan voltage low 热交换器风扇电压偏低 更换风扇，马达控制板5460 lamp anode fan - voltage too high 疝灯阳极风扇电压过高5461 lamp anode fan voltage high 疝灯阳极风扇电压偏高 更换风扇，马达控制板5462 lamp anode fan voltage too low 疝灯阳极风扇电压过低 更换风扇，马达控制板5463 lamp cathode fan voltage low 疝灯阴极风扇电压低 检查阴极风扇或控制板5470 lamp cathode fan - voltage too high 疝灯阴极风扇电压过高5471 lamp cathode fan voltage high 疝灯阴极风扇电压偏高 更换风扇，马达控制板5472 lamp cathode fan voltage too high 疝灯阴极风扇电压过高 更换风扇，马达控制板5473 lamp cathode fan - voltage low 疝灯阴极风扇电压偏低5490 smps fan - voltage too high 开关电源风扇电压过高5491 smps fan - voltage high 开关电源风扇电压偏高5492 SMPS fan voltage too low 开关电源风扇电压过低 更换风扇，马达控制板5493 SMPS fan voltage low 开关电源风扇电压偏低 更换风扇，马达控制板5501 FIB +12v voltage high +12v 电压偏高 检查供电板和开关电源5502 FIB +12v voltage low +12v 电压偏低 检查供电板和开关电源5510 tec green - voltage too high TEC绿色 - 电压过高5511 tec green - voltage high TEC绿色 - 电压偏高5512 tec green - voltage too low TEC绿色 - 电压过低5513 tec green - voltage low TEC绿色 -电压偏低5521 motor ,lens ,dowser voltage high 马达镜头光闸电压高 更换风扇，马达控制板5523 motor ,lens ,dowser voltage low 马达镜头光闸电压低 更换风扇，马达控制板5530 pump - voltage too high 泵电压过高5531 pumpvoltage high 泵电压偏高 更换风扇，马达控制板5532 pumpvoltage too low 泵电压过低 更换风扇，马达控制板5533 pumpvoltage low 泵电压偏低 更换风扇，马达控制板5540 tec red - voltage too high TEC红 - 电压过高5541 tec red - voltage high TEC红 - 电压偏高5542 tec red - voltage too low TEC红 - 电压过低5543 tec red - voltage low TEC红 - 电压偏低5550 tec - voltage too high TEC半导体制冷器电压过高5551 TEC voltage high TEC半导体制冷器电压偏高 检查单元线，控制板5552 tec - voltage too low TEC半导体制冷器电压过低5553 TEC voltage low TEC半导体制冷器电压偏低 检查单元线，控制板5561 ELCA box fan voltage high ELCA box风扇电压高 检查单元线，温度传感器，控制板5563 ELCA box fan voltage low ELCA box风扇电压低 检查单元线，温度传感器，控制板5570 lamp rear fan - voltage too high 灯后置风扇电压过高5571 lamp rear fan voltage high 灯后置风扇电压高 更换风扇，马达控制板5572 lamp rear fan voltage low 灯后置风扇电压低 更换风扇，马达控制板5573 lamp rear fan voltage too low 灯后置风扇电压过低 更换风扇，马达控制板5581 +12v voltage high +12v电压偏高 更换风扇，马达控制板5583 +12v voltage low +12v电压偏低 查电源板，风扇，马达控制板5590 tec red front - voltage too high TEC红前 - 电压过高5591 tec red front - voltage high TEC红前 - 电压偏高5592 tec red front - voltage too low TEC红前 - 电压过低5593 tec red front - voltage low TEC红前 - 低电压5600 tec green front - voltage too high TEC绿色前线 - 电压过高5601 tec green front - voltage high TEC绿色前线 - 电压偏高5602 tec green front - voltage too low TEC绿色前线 - 电压过低5603 tec green front - voltage low TEC绿色前线 - 电压偏低5610 tec blue front - voltage too high TEC蓝色前 - 电压过高5611 tec blue front - voltage high TEC蓝色前 - 电压偏高5612 tec blue front - voltage too low TEC蓝色前-电压过低5613 tec blue front - voltage low TEC蓝色前 - 低电压5620 electronics fan 1 (top side) - voltage too high 电子风扇1（顶面） - 电压过高5621 electronics fan 1 (top side) - voltage high 电子风扇1（顶面） - 电压偏高5622 electronics fan 1 (top side) - voltage too low 电子风扇1（顶面） - 电压过低5623 electronics fan 1 (top side) - voltage low 电子风扇1（顶面） - 电压偏低5630 electronics fan 2 (bottom side) - voltage too high 电子风扇2（底部） - 电压过高5631 electronics fan 2 (bottom side) - voltage high 电子风扇2（底部） - 电压偏高5632 electronics fan 2 (bottom side) - voltage too low 电子风扇2（底部） - 电压过低5633 electronics fan 2 (bottom side) - voltage low 电子风扇2（底部） - 电压偏低5640 lamp power supplies，zero lamp power supplies detected 检查电源接口，换LPS模块 (疝灯电源无输出)5641 lamp power supplies- lamp is on but SMPS is off 换SMPS模块， LPS 模块 （疝灯亮但开关电源关闭）5642 lamp power suppliesat least one lamp power supply could not be detected （一个灯电源检测不到） 检查灯电源连线接触或更换灯或灯电源5643 lamp power suppliescommunication failed with at least one lamp power supply (至少一个疝灯供电装置通讯失败) 重新连接两个接口，更换整个灯电源模块5644 lamp power supplieslamp is on but at least one lamp power supply is off (疝灯点亮，但至少一个疝灯供电装置关闭) 重新连接两个接口，更换整个灯电源模块5646 lamp set onfailed 点灯失败 检查灯状况，运行时间是否超时5647 lamplamp is off due to an error 关灯保护 检查灯状况，运行时间是否超时5654 lamp run timeread failed 读取灯运行时间失败 检查灯箱是否装好5657 lamp run timeexceeds maximum灯超时 换灯，复位灯运行时间5658 lamp run timeread limits failed 读取灯运行极限时间失败 检查灯箱是否装好5659 lamp run timewarning 疝灯运行时间报警 换灯5670 dowser - set dowser open failed dowser - 集dowser打开失败5800 ti-boards - system status = fail 系统错-接触不良检查 检查输入抽屉和引擎的接触5801 ti-boards - security error, please authorize 安全问题-需安全认证 进行安全认证5802 ti-boards - power up self test = fail Ti板电源自检错 临时处理措施可以放映，或换板5803 ti-boards- powerup self test = fail ICP板问题5807 ti-icp - read system status failed Ti-ICP读系统状态失败 刷新软件并应用克隆，或更换ICP、HDSDI输入板，刷软件5811 ti-boards - power-good = fail Ti板电源问题 更换电源板5812 ti-icp - read satellite info failed Ti-ICP读信息错 更换HDSDI输入板5813 ti-icp - satellite firmware mismatch Ti-ICP固件不匹配 xxB系列ICP用到xxC上，刷新ICP软件，应用克隆5814 ti-icp - self test = fail ICP 拔插ICP，升级软件并克隆5815 ti-icp - certificate error TI-ICP - 证书错误5816 ti-icp - key error TI-ICP - 关键错误 5817 ti-icp - icp board not detected 没有检测到ICP板5830 TI Link decrypter - No communication TI连接解码-无通信，可以放映 Enigma接触问题，软件升级ICP到v2.1以上.或开关顺序问题，与服务器连接冲突，在服务器关闭的情况下，重启机器。5831 ti-link-decryptor - system error TI链接解密 - 系统错误5832 ti-link-decryptor - security tamper event TI链接解密 - 安全入侵事件5833 ti-link-decryptor - logical marriage tamper event 安全问题-逻辑匹配问题 应用克隆5834 ti-link-decryptor - physical marriage tamper event 安全问题-物理匹配问题 检查安全开关，进行安全认证5835 ti-link-decryptor - security log warning 安全log问题- Enigma 拔插或更换Enigma5836 TI-Link-descryptor-security log is full 日志已满5836 TI-Link-descryptor-security log error 安全log问题- Enigma拔插或更换Enigma5837 ti-link-decryptor - read system status failed 安全log问题- Enigma 拔插或更换Enigma5850 TI Link IMB - No communication TI链接IMB- 通信 IMB板问题5851 imb - service door tamper event IMB板拆卸5853 imb - logical marriage tamper event IMB被逻辑拆卸5854 imb - physical marriage tamper event IMB被物理拆卸5880 dolby 3d key-server - read status failed 杜比3D服务器读取状态失败5881 dolby 3d key-server - status = locked 杜比3D服务器状态锁定5882 3d module - read status failed 3D模块 - 读取状态失败5884 3d module - change status failed due to dolby 3d key-server lock （3D模块更改状态失败，原因是杜比3D服务器被锁定）5885 3d module - change status failed due to communication error （3D模块改变状态，由于通讯错误而失败）5890 3d module - colorwheel spin failed 3D模块色轮分解失败5891 3d module - colorwheel in failed 3D模块色轮输入失败5892 3d module - colorwheel out failed 3D模块色轮输出失败5893 3d module - colorwheel temperature too high 3D模块色轮温度过高5894 3d module - colorwheel speed not ok (not locked) 3D模块色轮速度不正常（未锁定）5960 light pipe - temperature too high 导光管- 温度过高5961 light pipe - temperature high 导光管 - 温度偏高5962 light pipe - temperature too low 导光管 - 温度过低5963 light pipe - temperature low 导光管 - 温度偏低5964 light pipe - temperature sensor open 导光管 - 温度传感器开路5965 light pipe - temperature sensor short 导光管 - 温度传感器短路5970 dmd red front - temperature too high DMD红前 - 温度过高5971 dmd red front - temperature high DMD红前 - 温度偏高5972 dmd red front - temperature too low DMD红前 - 温度过低5973 dmd red front - temperature low DMD红前 - 温度偏低5974 dmd red front - temperature sensor open DMD红前 - 温度传感器开路5975 dmd red front - temperature sensor short DMD红前 - 温度传感器短路5980 dmd green front - temperature too high DMD绿色前线 - 温度过高5981 dmd green front - temperature high DMD绿色前线 - 温度偏高5982 dmd green front - temperature too low DMD绿色前线 - 温度过低5983 dmd green front - temperature low DMD绿色前线 - 温度偏低5984 dmd green front - temperature sensor open DMD绿色前线 - 温度传感器开路5985 dmd green front - temperature sensor short DMD绿色前线 - 温度传感器短路5990 dmd blue front - temperature too high DMD蓝色前 - 温度过高5991 dmd blue front - temperature high DMD蓝色前 - 温度偏高5992 dmd blue front - temperature too low DMD蓝色前 - 温度过低5993 dmd blue front - temperature low DMD蓝色前 - 温度偏低5994 dmd blue front - temperature sensor open DMD蓝色前 - 温度传感器开路5995 dmd blue front - temperature sensor short DMD蓝色前 - 温度传感器短路6000 block front - temperature too high 模块正面的温度过高6001 block front - temperature high 模块正面 - 温度偏高6002 block