发电电焊机英文版说明书.doc

Forward speechNote: when you receive the 250A diesel power generation electric welding machine, do not know how to operate, can Ou Bao this generic generating and welding dual-purpose machine manual reference, Zhang Jialiang is think so, internal combustion electric welder and gasoline power generation machine is actually using the general!1, add oil (diesel power generation electric welding machine to join 1.5 liters, 1 liters of gasoline power generation electric welding machine to add oil)Remember do not add too much or too little, more influence on the service life, and no way to start.2, add fuel, check whether the battery terminal has received immediately.Start 3; (diesel welder throttle switch should in gas state (right), and press and hold the power of the valve twist the key in the ignition for two seconds and releasing pressure reducing valve and the key to start the car), downtime is closed key press red button at the throttle switch below, throttle release natural stop and start all over again must be added the throttle switch. Gasoline welding machine is started. First of all, the door should be in the open state (air filter above the throttle pull rod pull out), then direct twisting key ignition start, start after the first time to close the throttle (choke rod must press enter)5, when the welder should maintain maximum current switch open, DC regulating switch must be twisted to the maximum. The machine is best not to use other appliances when using welding work, if necessary to use appliances, you can use her own watch.6, welder quick joint then qualify the provisions of is to use more than 35 square or 50 square feet of Doppler line, too much is not good, too small will burn), the length of the provisions is less than 8 meters, principle of not more than 10 meters, remember if connected to the output line is too long will affect the service quality, will lead to black smoke, the card machine, even the shutdown of phenomenon7, welder red fast joint interface is welding (welding). Black is a is connected with the guide wire, remember, pick the wrong can not be normal use. An allThe following marks, to remind the user, once operational errors, may cause personal injury.Once the operation mistake, may cause death or serious injury. Once the operation error, may cause moderate damage or loss of material.Although it will not cause the accident, but will affect the performance of the machine life.1 safe useNote the use of fuel before the 1-1 operation noticeThis fuel for diesel fuel, there shall be no machine around the kindling, in case of fire.You must stop the gas, and the diesel must be dried with a cloth. The exhaust pipe shall not be placed around the fuel or other flammable.Exhaust noteThis causes livestock poisoning in long time will use bad ventilation indoors or in enclosed spaces.Notes on the use ofThis daily inspection, regular inspection, maintenance, refueling, cleaning work, must first stop, then press the manual operation.Electric shock, leakage precautionsAudiences to prevent electric shock, leakage, please dont with wet hands or in the rain and snow and machine is wet operation and use.In the operation, please do not touch the welding terminal by hand, must first stop, then the welding wire.I do not use the damaged insulation rubber welding wire.Note when cleaning the machineOnion please fabric or compressed air cleaning, is not available for washing or cleaning agents, in order to avoid insulation deterioration, malfunction.Security issues outside of the manual record, please careful attention.When handling the matters needing attention 1-2I installed or unloading machine, please use the rope, the pulley frame hanging on horizontal loading, not available rope engine parts or generator parts.This machine must be shut down when handling machine.Sandy, when in use, please under the machine pad plate, to prevent sand suction within the engine caused by bad insulation.Please put the machine in the welding spatter flame ring.I refer to 1-1Note before the start of the 1-4This worker should wear overalls, gloves, hats, welders, using a mask.Should be checked before starting, if there is abnormal, first maintenance and then start.Reference 1-1Note in 1-5 operationRun in or just off, the exhaust pipe temperature is very high, careful burns.Reference 1-11-6 maintenance, custody matters needing attentionPlease place in a dry, clean, low salt room.To avoid long-term use of plastic cloth cover, so as to avoid rust or poor insulation.Before long-term storage, please remove the battery, put a clean fuel, make maintenance, in order to use.At least 3 months to run once, to confirm the status of the machine.Reference 1-12 specification and dataTO250A-柴油发电电焊机产品编号TO250A款式手推式品牌大泽动力额定输出功率HP20绝缘等级F电焊机下降特性单把电流调节范围0-250A空载电压65V工作电压22-30V负载持续率100%适用焊条mm2.05.0电焊同时辅助功率额定输出KW5最大输出KW6发电机额定电压V220（可选配380V）耗油量205g/kw.h功率因数%100工作状态连续发动机名称192F（YOTOTI）发动机形式单缸直列四冲程风冷柴油机缸体数1排气量420CC额定转速rpm3000启动方式手启动|电启动燃油型号0号柴油（夏）-10号柴油（冬）其他工作环境温度-2040油箱容量L20最大尺寸mm770*510*660净重Kg120噪音dB70机油容积1.05L连续工作12HPayment: 100% advance payment, payment to the delivery.Delivery date: within 2 working days after receipt of your order and remittance.Europe Bao power source in ItalyContact: Zhang Gong (Manager)Tel:ax 021-619242344 check before starting4-1 check oilMust be checked before starting the engine oil, oil position should be between the upper and lower limits, check the oil standard to be completely inserted, too much oil will cause damage to the engine, you must pay attention to.Do not pull out the oil scale in operation, the oil will be sprayed out, very dangerous.Please use more than CD diesel engine oil, low quality oil will affect the engine life.Different brands of oil must not be mixed.4-2 check fuelPlease, before starting to check and fill fuel.Please use light diesel oil. Low quality diesel will affect the output or cause trouble.4-3 check lineOften check the line connector has no loose, broken, insulation damage, so that timely disposal. After the inspection is completed, start the machine, and then pay attention to see whether there is no oil leak.4-4 check coolant volumeWhen the temperature is lower than zero, the cooling liquid must be selected according to the bottom temperature. Absolutely can not use water.First stop the engine and confirm the full cooling. Slowly open the radiator cap to reduce the internal pressure, otherwise the radiator cover may be pushed open, hot air emitted, resulting in burns or other accidents.Check the water level of the auxiliary water tank. If there is a shortage, please fill in the normal level. (higher than LOW).If the secondary water tank coolant is close to the opening, the auxiliary water tank is filled with coolant.Daily maintenance, do not open the radiator cap.After tightening the radiator cap to check the coolant level, tighten the radiator cap, or the internal pressure may blow away the radiator cap and cause a major accident.5-1 features5 the characteristics and functions of the machineBrushless generator, maintenance is simple.Excellent welding characteristics, suitable for all kinds of welding needs.Idle device, saving energy.5-2 idle speed deviceIdle speed device in welding operation or the use of auxiliary power supply in respite when automatically reduce the engine speed, save energy source, reduce the noise effect.Idle device no matter whether the welding operation or auxiliary power supply, as long as the idle switch on the open can be.This welding operation, as long as the electrode contact the parent material, the engine instantly rose to rated speed. On the contrary, after 7 seconds, the engine automatically enters the low speed operation.When using auxiliary power, as long as the current through about 1.0A, the engine can be instantly rose to the rated speed. On the contrary, automatically enter the low speed operation.Welding and auxiliary power supply can not be used at the same timeAuxiliary power supply can not be used for AC power equipmentWhen using small load electrical appliances or electromagnetic contactor, automatic idle device may not operate, at this time please put the idle switch in the off position.5-3 protection deviceThe auxiliary power supply circuit is equipped with abnormal current and over current checking circuit. (including electronic protection devices, fuses and circuit breakers 3). Once the abnormal current occurs, it will burn off the fuse, over current will cause damage to the substrate.Once the power is not output, please stop, find out the reason and then start.If there is still no output after the start, check the fuse.The circuit breaker can not be used as a power switch.6 operation method6-1 start engineThe auxiliary DC switch (circuit breaker) on the off. Idle switch on the open. The ignition key is rotated to the starting position, the car.Low temperature in winter when the ignition key is rotated to the preheat position, preheat indicator lamp goes out after then rotate to start position, the car and let go.Warm in idle state for 5 minutes. In operation, the indicator light statusWhen the start switch is in the run position, the normal indication of each indicator is as follows:Indicator lamp oil pressure water temperature charging preheatingBefore starting(the key is in the open position)Bright,- outBright,Bright,Preheating is finished,Bright.Out,Bright.DestroyThe engine is running (no load) -DestroyThis engine is in operation, can not start again, so as to avoid actuator failures.After the start, be sure to warm in the idle state for 5 minutes, immediately after the start of the load will affect the life of the welding machine.Run to check whether there is no (diesel, oil) oil spill., the machine speed control rod at the factory have been sealed, must not be allowed to adjust itself. If the bicycle after pulling will cause the engine speed disorder, damage to the machine.6-2 stopWhen the switch is placed in the closed