EM-2001易速达汽车引擎强化加速晶片

1 EM 2001 易速達汽車引擎強化加速晶片 e Star Automobile Engine Reinforcing Accelerate Chips Model No EM 2001 理論基礎 本產品之理論基礎是利用二價 三價鐵 Fe 2 Fe 3 材料 受到天然能量的波 場引響 該鐵原子的核旋轉和電子旋轉就發生變化 成為所謂激發狀態 Excited state 而具有高階能量 此高階能量能持續 10 年以上產生每秒一千億次之自然震 盪波 藉本晶片的整流共振作用 而有效地將空氣中的氫氧分子迅速活化 微細化 使其瞬間成為類離子狀態 當活化後的空氣進入引擎燃燒室時 對燃油分子的承載 量可以達到 16 倍以上 並使油氣混合比達到 1 14 5 之最佳比例 經檢驗測試 e star 引擎強化晶片 能有效使燃油達到完全燃燒 並提昇引擎效率達 10 20 Rationale Rationale of the product is to provide iron atoms with high order energy by changing their nuclear and electron spins in a so called excited state when divalent and trivalent irons Fe 2 Fe 3 are affected by the wave zone of natural energy Such high order energy can consistently generate one hundred billion natural oscillation waves per second for more than ten years to effectively activate and micronize the hydroxide molecules in the air to be in an ion like status instantaneously by means of the chip s rectification and resonance Then when the activated air enters the combustor the load carrying capacity of fuel molecules can be increased more than 16 times to reach the optimal fuel air mixture ratio of 1 14 5 Through many tests and inspections e star Automobile Engine Reinforcing Chip has been proven to be able to help achieving total fuel combustion and improving engine efficiency by some 10 20 安裝方法 將空氣濾清器之螺絲或金屬簧夾鬆開 再將上蓋打開 取出空氣濾蕊 如圖一 將 e star 引擎強化晶片 平均鋪於濾蕊上方 如圖二 以附件卡夾插入 e star 引擎強化晶片 兩對角洞口 如圖三 4 將卡夾按下連結空氣濾蕊 使 e star 引擎強化晶片 不致鬆脫即可 再將空氣 濾蕊鎖回濾清器 如圖四 Installation Loosen the screws or metal clips on the air filter to open the top cover before taking the air filter cartridge out as shown in Fig 1 Place e star Automobile Engine Reinforcing Chips evenly on the filter cartridge as shown in Fig 2 Insert the attached jump rings into the two diagonal holes on the e star Automobile Engine Reinforcing Chips as shown in Fig 3 Press the jump rings to connect with the air filter cartridge and ensure that the e star Automobile Engine Reinforcing Chips will not fall out before securing the air filter cartridge back in the air filter as shown in Fig 4 D I Y 調校法 2 本產品安裝後經適當調校後可立即彰顯效果 1 當安裝完成後 請發動引擎 並將排檔桿推至空檔 N 同時關掉冷氣開關 2 踩油門踏板 將引擎轉速拉至 3000 4000rpm 維持 3 5 分鐘 然後回歸怠速狀 態 3 停留怠速約 3 分鐘 最後再重踩油門踏板 將轉速拉至紅線區 5000 6000rpm 隨即瞬間急放油門踏板並來回猛踩剎車踏板數次 當明顯感覺剎車踏板上浮時 即 已提昇剎車效率 4 以上動作在安裝本產品後及每行駛 5000 公里實施車輛定期保養後自行調校即可 DIY Tuning After being installed the product shall reveal its best performance through appropriate tuning After installation please start the engine and engage the gear into neutral N and turn the air conditioner off at the same time Step on the accelerator to increase the engine speed to 3000 4000rpm for 3 5 minutes before returning to idling condition Remain idling for approximately 3 minutes before stepping on the accelerator again to increase the engine speed into the red zone 5000 6000rpm for approximate 3 seconds Then quickly step off the accelerator and foot heavily on the brake several times When the brake pedal is apparently moving up it indicates that the braking efficiency has been improved The foregoing DIY tuning procedure shall be carried out after the product is installed and every 5000km regular maintenance 注意事項 1 e star 引擎強化晶片 安裝時無正反面之分 安裝時以平鋪於空氣濾蕊上方為 佳 2 e star 引擎強化晶片 安裝數量 以能覆蓋空氣濾蕊 70 以上面積時效果最好 3 安裝 e star 引擎強化晶片 後 請定期做好車輛保養維修工作 使用原廠機油 或空氣濾蕊更能有效彰顯晶片效果 4 本晶片為高精密半導體材質 不可重摔以免碎裂 本晶片如有髒污 可用清水沖 洗 不可使用化學藥劑或用刷子摩擦表面 Notices During installation it is recommended to place e star Automobile Engine Reinforcing Chips flatly above the air filter cartridge It does not matter which side shall face up The best performance can be obtained if more than 70 of the air filter cartridge is covered by e star Automobile Engine Reinforcing Chips After installing e star Automobile Engine Reinforcing Chips please carry out regular maintenance on the vehicle and only apply the engine oil and air filter cartridge supplied by the original manufacturer in order to maintain the optimal performance of the chips The chip is made of high precision semiconductor materials and shall avoid breakage due to heavy falling Please apply clean water to wash the chip if any dirt exists Do not apply any chemical or use brush on the surface 檢測報告 檢測單位 財團法人車輛研究測試中心 ARTC 3 車型 CITROEN BX16TRS M5 五門小客車 車身號碼 VF7XBXB0047XB9889 輪胎型式 195 60R14 引擎型式 前置直列四缸 排檔型式 手排五檔 污染測試 測試項目COTHC 安裝前31 30 g km15 924 g km 加裝 e star18 73 g km2 462 g km 耗能測試 測試項目市區耗能高速耗能平均耗能 安裝前8 90 km 13 93 km 10 6 km 加裝 e star10 19 km 15 25 km 12 0 km 加速性測試 註 測試項目極速 km hr0 100km 加速性 sec 安裝前13813 9 加裝 e star15013 0 檢測日期 2000 12 27 2001 1 4 報告編號 BB TT289G205 BB TT289G206 註 為試用者安裝後實際道路測試值 本產品為專利品 台灣專利號 中華人民共和國專利號 2 Inspection Report Inspection Organization Automobile Research and Test Center ARTC Model CITROEN BX16TRS M5 5 door Sedan Body Number VF7XBXB0047XB9889 Tire 195 60R14 Engine Front located In line 4 cylinder Gear 5 speed Manual Pollution Test Test ItemCOTHC Before Installing e star31 30g km15 924g km After Installing e star18 73g km2 462g km Power Consumption Test Test ItemSlow SpeedHigh SpeedAverage Before Installing e star8 90km l13 93km l10 6km l 4 After Installing e star10 19km l15 25km l12 0km l Acceleration Ability Test Test ItemTop Speed km hr 0 100km sec Before Installing e star13813 9 After Installing e star15013 0 Test on 2000 12 27 and 1001 1 4 Report Number BB TT289G205 and BB TT289G206 Item C test values were obtained from actual road test after installation of e star The product is a patented product Taiwan Patent No and China Patent No 2 易速達汽車引擎強化加速晶片 客戶安裝疑難解答 e Star Automobile Engine Reinforcing Accelerate Chips DIY Installation Q A 我的愛車安裝後仍覺得引擎無力 怎麼辦 A 如安裝後愛車仍覺得無力 原因可能如下 原 因檢 查 方 式解 決 方 法 一 空氣濾清器濾蕊已無法使空 氣流動 引擎吸氣量不足 檢查空氣濾清器濾 蕊是否非常骯髒 請更新空氣濾清器濾蕊貨加 以清潔 依目前台灣環境 每車行 15 000 20 000 公里 須更新空氣濾清器濾蕊 二 您的愛車積碳已 阻塞噴油 嘴 火星塞及汽缸 若不盡 快加以處理 您的愛車會常 熄火 無力 耗油 檢查火星塞是否嚴 重積碳 請更換新的原廠火星塞 並 送保養廠清洗積碳 三 機油已老化 變質 造成油 泥堵塞機油濾蕊 並且造成 引擎積碳 檢查機油中是否有 黑色顆粒積碳貨油 泥 請更換機油及機油濾清器 What shall I do if the engine remains powerless after installation of e star A Possible causes are listed out as follows CauseChecking MethodTroubleshooting 1The air filter cartridge is defected causing insufficient air inflow in the engine Check whether the air filter cartridge has become filthy The air filter cartridge shall be replaced or cleaned Based on current environment in Taiwan the air filter cartridge shall be replaced after every 15 000 20 000km travelling 2Carbon deposits have blocked fuel injector spark plugs and cylinders causing frequent stall low power and high fuel consumption Check whether carbon deposits have built up on the spark plugs Please replace spark plugs with new ones made by the original manufacturer and send the car to a service center for removal of carbon deposits 5 3Engine oil has become aged and deteriorated causing grease blockage in the oil filter cartridge and carbon deposits in the engine Check whether any carbon deposit or grease exists in the engine oil Please make oil change and replace oil filter 我的車是十年前的福特全壘打 安裝 e star 引擎強化晶片 後明顯感覺車子馬力 變大 但卻無省油效果 怎麼回事 A 其實您的愛車已開始省油了 使用本產品後您的愛車機件在一切都正常狀況下 一定會達到理想的省油效果 而以少量的燃油即便產生最大的動力 但是如果有以 下的狀況 則有可能影響您愛車的省油程度 原 因檢 查 方 式解 決 方 法 一 引擎燃燒室嚴重積碳火星塞頭充滿積碳 爬波無力 起步時 會有霹啪聲 請至原廠保養 要求清除積 碳 並更換火星塞 大部分 原廠保養廠不主動幫客戶清 除積碳 除非您主動提出要 求 二 空氣濾清器功能不佳取出空氣濾清器濾 蕊 檢查兩面是否 佈滿沙塵及受油污 污染 請更換原廠空氣濾清器濾蕊 三 自動變速箱油質劣化檢查自動變速箱油 是否變稀薄而無黏 性 加速變檔時有 2 秒以上之遲緩獲暴 衝現象 建議每行駛 10 000 公里更換 一次自動變速箱油 四 供油系統怠速供油量尚未配 合調整 將排檔推入低速檔 不踩油門 發現車 速前進很快 起步 力道過於強勁 噴射點火引擎 經 7 15 天 引擎將自動調整噴油量 化 油器引擎須調整怠速螺絲及 油氣混合比螺絲至最佳狀態 五 油門踏踩習慣不良起步時僅須輕微將腳輕放於油門踏板上 加速時 輕踩油門製引擎轉速 1 200 1 500rpm 處 如前方 有紅燈或須停車狀況 提前放鬆油門使車行速度 不致迅速下降 讓車自然滑行停止 如此保持良 好駕車習慣 則可增進省油效率 六 駕駛人有賽車心態加裝本晶片後 在馬力與扭力大幅提昇下 請勿 強踏油門來追求速度感 此對省油效果無益 I own a 1991 Ford Telstar After installing e star Automobile Engine Reinforcing Chips it has become more powerful but shows no significant fuel saving effect Why A In fact fuel saving has become effective on your car After installing e star Automobile Engine Reinforcing Chips the car can surely achieve the expected fuel 6 saving effect under normal circumstances while maximum power can be generated with only little fuel required Nonetheless fuel saving effect may be affected if any of the following conditions exists CauseChecking MethodTroubleshooting 1Severe carbon deposits have built up in the engine combustor Inadequate power and noise occur during uphill running and starting respectively if spark plugs are filled with carbon deposits Please have the car serviced by the original manufacturer and ask for removal of carbon deposits most of the service centers do not provide such service automatically unless under customer request and replacement of spark plugs 2Functions of air filter are unsatisfactory Take the air filter cartridge out to check whether it is covered with dusts or contaminated by grease on both sides Please replace the air filter cartridge with new one made by the original manufacturer 3Quality of automatic transmission oil has deteriorated Check whether the automatic transmission oil has become diluted without any viscosity and slow or sudden responding occurs for more than 2 seconds during gear changing It is recommended to have the automatic transmission oil changed every 10 000km 4Idling fuel supply has not been appropriately adjusted When engaged in low gear without acceleration the car travels fast and becomes over powerful during start For fuel injection engine the engine will adjust the amount of fuel injection automatically every 7 15 days For carburetor engine it is necessary to adjust the idling screw and the fuel air mixing ratio screw to obtain the optimal performance 5The way to accelerate is incorrect It only needs to step gently on the accelerator pedal to start running or increase the engine speed to 1 200 1 500rpm for acceleration To stop the car on a red light or when necessary the driver shall foot off the accelerator in advance and allow the car to stop slowly without sudden braking Such good driving habit shall be maintained to improve fuel saving efficiency 7 6The driver drives as if in a car race Power and torque of the car will increase significantly after the chips are installed Please refrain from stepping heavily on the accelerator in the pursuit of speed This will not help saving fuel 3 我已安裝市面上之省油加速器感覺無效 而油管已剪斷 是否也可以安裝 e star A 本公司 e star 引擎強化晶片 不須更改您愛車油路 電路 所以您不須至保 養廠自己即可安裝 如果您已經安裝須剪斷油管之省油加速器 對本產品無任何副 作用 但必須於開車前須檢查該省油器與您愛車油管銜接處是否有漏油現象 My car is equipped with another fuel saving accelerator that however does not appear to be very effective Now the fuel pipe has been cut off Is it possible to install e star on my car A It does not need to change any of the car s fuel pipes or electric circuits when installing our e star Automobile Engine Reinforcing Chips You can do installation yourself without having to send the car to the service center The fuel saving accelerator that needed to cut off the fuel pipe shall not affect our product Nevertheless it is necessary to check whether there is any leakage at the joint between the fuel saving accelerator and the fuel pipe before starting 4 我的愛車安裝 e star 後排氣管會產生水滴 是不是冷氣水 A 冷氣水是不會從排氣管中滴出的 由於您愛車的引擎效率已經提昇 在完全燃 燒的狀況下會產生二氧化碳和水蒸氣 CO2 H2O 水蒸氣經排氣管慧冷凝成水滴 滴下 此即表示您愛車引擎已經完全燃燒而開始提昇馬力及省油了 Some water drops are generated on the exhaust pipe after installing e star on my car Does air conditioner generate them A Water generated by air conditioner does not come out from exhaust pipe As the engine efficiency of your car has improved after installing e star carbon dioxide and water vapor CO2 H2O will be generated under total combustion Water vapor will then condense into water drops and drip out from exhaust pipe Such phenomenon indicates the engine of your car has achieved total combustion and has started improving power and saving fuel 5 聽說安裝 e star 引擎強化晶片 後會提昇剎車效果 該怎麼調整 多久做一次 A 1 當安裝完成後 請發動引擎 並將排檔桿推至空檔 同時關掉冷氣開關 2 踩油門將引擎轉速拉至 3000 4000rpm 維持 3 5 分鐘 然後回歸怠速狀態 3 停 留怠速約 3 分鐘 最後再重踩油門踏板 將轉速拉至紅線區 5000 6000rpm 約三秒 鐘 然後急放油門踏板並來回猛踩剎車踏板數次 當明顯感覺剎車踏板上浮時 即 已提昇剎車效率 4 以上動作在安裝本產品後及每行駛 5000 公里實施車輛定期保 養後自行調校即可 I have been told that braking effect will be improved after installing e star Automobile 8 Engine Reinforcing Chips What are the adjustments required and how often do I need to carry out the adjustments A 1 After installation please start the engine and engage the gear into neutral and turn the air conditioner off at the same time 2 Step on the accelerator to increase the engine speed to 3000 4000rpm for 3 5 minutes before returning to idling condition 3 Remain idling for approximately 3 minutes before stepping on the accelerator again to increase the engine speed into the red zone 5000 6000rpm for approximate 3 seconds Then quickly step off the accelerator and foot heavily on the brake several times When the brake pedal is apparently moving