运输企业车辆技术管理台账

东明县昌顺运输有限公司车辆技术管理台账车 辆 情 况 登 记 台 账 序号车号厂牌型号车辆类型燃油类别吨座位购入日期罐体容积卫星定位系统型号停驶、待废或其它车 辆 维 修 台 账车号：车型： 项目日期当前里程维修类别维修项目更换主要部件费用承修单位试车记录送修负责人 车 辆 检 测 登 记 台 账序号车号厂牌型号车辆类型检测时间检测类别下次检测时间备注注：检测类别为二级维护检测、技术等级评定检测车辆安全检查登记台帐抽、 检 查 项 目处理意见驾驶员签字检查人签字 项目检查情况车牌号码制 动转 向灯 光传动 、 悬挂油箱 、 轮胎消 防 器 材危险品标志牌、灯导除静电装置隔离电火花装置阻 火 器阀 门槽罐完好情况各部件紧固车辆二维、等评情况防护用品使用情况企业自定项目备 注说明：1、该台帐须由车辆管理人员负责填写登记；2、合格打，故障打，发现有故障的车辆必须立即停止营运，并按规定排除故障。 抽查日期： 年 月 日车 辆 技 术 等 级 台 帐 车号车别评定日期审验日期里程表示值(km)评定等级评 定 单 位评定人备 注 车 辆 事 故 台 账 车号车别事故发生日 期事故发生地点事故性质事 故 原 因车辆损坏情况直接经济损失(元)备注地形平坦开阔，地层由第四系全新冲积层，第四系上更新统冲层组成，局部表覆第四系全新统人工堆积层。第四系全新统冲积层厚度约2550m，岩性主要为黏土、粉质黏土、粉土、粉砂、细砂；第四系上更新统冲积层厚度大于50m，岩性主要为黏性土、粉土、粉细砂等。管桩深度范围内地层主要为：粉土、黏土、粉质黏土，局部表层为杂填土。coupling Centre shall be checked, the second poured concrete strength of more than 70%. In the process of reaming or boring, apart from the special provisions in factory, does not allow any work that may affect the coupling Centre, such as irrigation, to cylinder connections to flood the condenser pipes and so on. Well boring, hinge bolt hole flange with coupling of vertical, not oblique. Mounting bolts should be added lubricants, typing gently with a small hammer, not too loose or too tight, packed the bolts with the corresponding seal screw hole should be marked. 6.4.5.4.2 coupling reamed and pairings is close to the diameter of bolt bearing good hinge holes, dressed with a good two coupling bolts before you can move the rotor, boring-reaming hole in turn. Coupling bolts must be tight coupling is symmetrical diameter, in boring, reaming, two bolts out. Well boring, hinge bolt hole flange with coupling of vertical, not oblique. Due to the coupling bolts in accordance with hinge holes corresponding to the diameter of the screw holes one by one after processing, processing back bolt installation location cannot be changed, so according to bolt after the actual weight difference of nut and lock washer to match. General requirements for coupling two symmetrical diameter bolt, nut and lock washers total weight difference should not be greater than 10 g and knocks stamped mark. (See Figure 18) The coupling bolts apply lubricant, and then gently with copper home, not too loose or too tight. Bolt Assembly is finished, symmetrical tightening all bolts to 30%, 50%, 70%, 100% force, and check the coupling flutter and before connecting the circle gradually changes its value should be less than 0.02mm. Tightening torque of the coupling bolts shall comply with the technical requirements manufacturers drawings,