HPUX系统安装-清晰完整步骤.doc

HP-UNIX系统安装完整步骤（rx6600）HP主机重新安装系统时。主机加电，放入光盘-用串口线连接主机串口-查看看MP端口的ip地址-网线连接到主机MP口-进入a MP:CM -输入co 进入控制窗口-选择internal bootable dvd 启动a MP:CM MP MAIN MENU: CO: Console VFP: Virtual Front Panel CM: Command Menu SMCLP: Server Management Command Line Protocol CL: Console Log SL: Show Event Logs HE: Main Help Menu X: Exit Connectiona MP co Use Ctrl-B or ESC-( to return to MP main menu.- - - - - - - - - - Prior Console Output - - - - - - - - - -HPUX HPUXHPUX 开始安装，（此时会输出主机的硬件信息）- - - - - - - - - - - - Live Console - - - - - - - - - - - -* ROM Version : 04.03* ROM Date : 04/08/2008* BMC Version : 05.23*0 0 0x0015B2 0x0000000023232801 boot time event 1 0 0x0000A4 0x0000000000000000 start memory configuration提示输入语言Enter the number of the language you want: 26a MP:CM help -进入帮助HE= MP Help: Main Menu =Hardware Revision S0 Firmware Revision F.02.17 Oct 5 2007,16:53:04Integrated Lights-Out for HP Integrity - Management Processor (MP) MP Help System Use Ctrl-B to exit MP command interface and return to the main MP menu. Enter a command at the help prompt: OVerview : Launch the help overview LIst : Show the list of MP Command Menu commands : Enter the command name for help on individual command TOPics : Show all MP Help topics and commands HElp : Display this screen Q : Quit help=MP:HE MP MAIN MENU: CO: Console VFP: Virtual Front Panel CM: Command Menu SMCLP: Server Management Command Line Protocol CL: Console Log SL: Show Event Logs HE: Main Help Menu X: Exit Connectiona MP cm (Use Ctrl-B to return to MP main menu.)a MP:CM pe关闭/开启电源a MP:CM pePCCurrent System Power State: On Power Control Menu: C - Power Cycle ON - Power On OFF - Power Off G - Graceful ShutdownEnter menu item or Q to Quit: offoffSystem will be powered off. You must shut down the OS manually before this command is executed. Failure to do this can cause problems when the OS is restarted. Confirm? (Y/N): yy - System is being powered off.a MP:CM pePCCurrent System Power State: Off Power Control Menu: C - Power Cycle ON - Power On OFF - Power Off G - Graceful ShutdownEnter menu item or Q to Quit: ononSystem will be powered on. Confirm? (Y/N): yy - System is being powered on.改MP的ip地址a MP:CM helpHE= MP Help: Main Menu =Hardware Revision S0 Firmware Revision F.02.17 Oct 5 2007,16:53:04Integrated Lights-Out for HP Integrity - Management Processor (MP) MP Help System Use Ctrl-B to exit MP command interface and return to the main MP menu. Enter a command at the help prompt: OVerview : Launch the help overview LIst : Show the list of MP Command Menu commands : Enter the command name for help on individual command TOPics : Show all MP Help topics and commands HElp : Display this screen Q : Quit help=MP:HE listlist= MP Help: Command Menu List =BP : Reset BMC Passwords PC : Remote Power Control CA : Configure asynch/serial ports PM : Remote Power Mode Control DATE: Display Date PR : Power Restore Policy Config. DC : Default Configuration PS : Power management module Status DF : Display FRU Information RB : Reset BMC DI : DIsconnect users RS : Reset System through RST signal DNS : Configure DHCP and DNS SA : Set MP Access FW : Upgrade MP firmware SNMP: Configure SNMP parameters HE : Display Help SO : Security Options ID : System Information SS : System processors Status IT : Modify MP inactivity timeouts SYSREV: Display System firmware Revs. LC : Configure LAN, SSH and Web ports TC : Reset system via INIT LDAP: Configure Directory parameters TE : TEll- send a msg. to other users LM : License Management UC : User Configuration LOC : Locator LED display WHO : Display connected MP users LS : LAN Status XD : Diagnostics and reset of MP =MP:HE LC -先将dhcp设为disable-重启-设置MP ip地址=1、系统安装前的准备准备HPUX的系统安装介质，以及配有光驱的性能稳定的目标主机。2、上电开机后，把安装盘放入光驱3、在主机自检过程结束后，10秒中断，如下所示Firmware Version 43.43Duplex Console IO Dependent Code (IODC) revision 1- (c) Copyright 1995-2002, Hewlett-Packard Company, All rights reserved- Processor Speed State CoProcessor State Cache Size Number State Inst Data - - - - - 1 550 MHz Active Functional 512 KB 1 MB Central Bus Speed (in MHz) : 133 Available Memory : 2097152 KB Good Memory Required : 31408 KB Primary boot path: 0/0/2/1.6 Alternate boot path: 0/0/2/1.6 Console path: 0/0/4/0.0 Keyboard path: 0/0/4/0.0 Processor is booting from first available device.To discontinue, press any key within 10 seconds.在此处，按键盘任何健，中断系统的正常引导，进入PDC环境，如下所示：Main Menu: Enter command or menu 4、在这个环境下可以做很多工作，做系统安装在这里需要找到光驱的路径，敲入sea命令Main Menu: Enter command or menu seaSearching for potential boot device(s)This may take several minutes.To discontinue search, press any key (termination may not be immediate).IODC Path# Device Path (dec) Device Path (mnem) Device Type Rev - - - - - P0 0/0/1/0.4 extscsi.4 Random access media 1 P1 0/0/2/0.6 intscsia.6 Random access media 1 P2 0/0/2/1.6 intscsib.6 Random access media 1 Main Menu: Enter command or menu 这里我们看到的是外置的光驱extscsi.45、Main Menu: Enter command or menu bo p0 Interact with IPL (Y, N, or Cancel)? nBooting. Boot IO Dependent Code (IODC) revision 1HARD Booted.ISL Revision A.00.43 Apr 12, 2000 ISL booting hpux (;0):INSTALLBoot: disk(0/0/1/0.4.0.0.0.0.0;0):WINSTALL11763712 + 1970264 + 2628048 start 0x200ae8alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x7fa00000.gate64: sysvec_vaddr = 0xc0002000 for 2 pagesNOTICE: nfs3_link(): File system was registered at index 4.NOTICE: autofs_link(): File system was registered at index 6.NOTICE: cachefs_link(): File system was registered at index 7. System Console is on the Built-In Serial Interface Swap device table: (start & size given in 512-byte blocks) entry 0 - auto-configured on root device; ignored - no roomWARNING: no swap device configured, so dump cannot be defaulted to primary swap.WARNING: No dump devices are configured. Dump is disabled.Starting the STREAMS daemons-phase 1Create STCP device files $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c Vw for CUPI80_BL2000_1108 build - cupi80_bl2000_1108 CUPI80_BL2000_1108 Wed Nov 8 19:24:56 PST 2000 $Memory Information: physical page size = 4096 bytes, logical page size = 4096 bytesPhysical: 2097152 Kbytes, lockable: 1555264 Kbytes, available: 1801372 Kbytes6、以上显示内容是从光驱引导的提示信息，直到出现如下界面在这个界面中，选中Install HP-UX选项，点击回车键，进入下个界面7、这个界面中，User Interface Options选项使用的较多的只有两个一是：Guided Installation，如果默认安装可以直接选择OK，下面的都是选择Next，直接到底不用任何干涉，只要换盘就可以了，等系统安装完成后按照提示设置一些系统的相关配置信息即可。二是：Advanced Installation，一般都是选择这个，因为通过这个可以预定好多系统的相关属性和信息，如软件包以及文件系统等等，下面详细介绍每一步8、上一界面中移动Tab键到Advanced Installation，并按Space选中，然后选择ok，进入下一界面，这里将对每一个选项卡中的相关内容做一定的解释和说明在上图所示Basic选项卡中，可以设置系统的基本配置、运行环境、安装的Root Disk、FileSystem的类型、Swap区的大小，以及设置系统语言环境等等，一般在本页不做任何修改。确认后，使用Tab键移到并选择Software或其他选项卡进行其他设置9、选CDE/ ignite/在如上所示Software选项卡中，可以选择一些必要的补丁或软件包。需要安装的只要使相关记录的Marked？属性变为Yes，方法是使用Tab键进入右边列表框，上下方向键选择相关记录，Space键进行Yes和No的切换。确认完后，使用Tab键移到并选择System或其他选项卡进行其他设置。10、在如上所示System选项卡中，可以设置主机名、网络相关配置、时间相关设置以及root用户密码等，借助Tab键及上下左右方向键选择相关参数并进行设置。当然也可以选择安装系统后设置这些信息，修改Final System Parameters即可。确认完后，使用Tab键移到并选择File System或其他选项卡进行其他设置。11、在如上所示File System选项卡中，可以设置 /var、/tmp、/home等文件系统的大小、类型，选择文件系统所属VG，VG进行扩容等等。其中/stand默认大小为300MB以及/Swap的默认大小为物理内存的两倍。借助Tab键及上下左右方向键选择相关参数并进行设置。确认完后，使用Tab键移到并选择Advanced或其他选项卡进行其他设置。12、 在如上所示Advanced选项卡中，可以设置一些脚本。确认完后，使用Tab键移到并选择其他选项卡进行其他设置，或者选择GO进行安装。13、以下所要做的就是等待、换盘，当安装结束后可能需要进行一些简单的配置,该例中系统以及网络相关先前全部配置完成。You can pay attention to the detail process as follows！* Loading configuration utility. * Beginning installation from source: /dev/dsk/c0t4d0= 01/18/06 02:11:17 EST Starting system configuration. * Configure_Disks: Begin * Will install B.11.11 onto this system. * Creating LVM physical volume /dev/rdsk/c2t6d0 (0/0/2/1.6.0). * Creating volume group vg00. * Creating logical volume vg00/lvol1 (/stand). * Creating logical volume vg00/lvol2 (swap_dump). * Creating logical volume vg00/lvol3 (/). * Creating logical volume vg00/lvol4 (/home). * Creating logical volume vg00/lvol5 (/opt). * Creating logical volume vg00/lvol6 (/tmp). * Creating logical volume vg00/lvol7 (/usr). * Creating logical volume vg00/lvol8 (/var). * Extending logical volume vg00/lvol1 (/stand). * Extending logical volume vg00/lvol2 (swap_dump). * Extending logical volume vg00/lvol3 (/). * Extending logical volume vg00/lvol4 (/home). * Extending logical volume vg00/lvol5 (/opt). * Extending logical volume vg00/lvol6 (/tmp). * Extending logical volume vg00/lvol7 (/usr). * Extending logical volume vg00/lvol8 (/var). * Making HFS filesystem for /stand, (/dev/vg00/rlvol1). * Making VxFS filesystem for /, (/dev/vg00/rlvol3). * Making VxFS filesystem for /home, (/dev/vg00/rlvol4). * Making VxFS filesystem for /opt, (/dev/vg00/rlvol5). * Making VxFS filesystem for /tmp, (/dev/vg00/rlvol6). * Making VxFS filesystem for /usr, (/dev/vg00/rlvol7). * Making VxFS filesystem for /var, (/dev/vg00/rlvol8). * Configure_Disks: Complete * Download_mini-system: Begin * Installing fileset OS-Core.CMDS-MIN,r=B.11.11 (9 of 684). 开始安装相关fileset* Installing fileset OS-Core.UX-CORE,r=B.11.11 (10 of 684).* Installing fileset OS-Core.CMDS-AUX,r=B.11.11 (11 of 684).* Installing fileset InternetSrvcs.INETSVCS-INETD,r=B.11.11 (12 of 684).* Installing fileset NFS.NFS-KRN,r=B.11.11 (13 of 684).* Installing fileset NFS.NFS-SHLIBS,r=B.11.11 (14 of 684).* File /usr/lib/libnsl.1 could not be removed. It was renamed and added to the cleanup file /var/adm/sw/cleanupfile.* Installing fileset NFS.NFS-CORE,r=B.11.11 (15 of 684).* Installing fileset Networking.100BT-KRN,r=B.11.11 (16 of 684).* Installing fileset Networking.LAN-KRN,r=B.11.11 (17 of 684).* Installing fileset Networking.LAN2-KRN,r=B.11.11 (18 of 684).* Installing fileset openssl.OPENSSL-RUN,r=A.00.09.07-d.002 (683 of 684). * Installing fileset openssl.OPENSSL-SRC,r=A.00.09.07-d.002 (684 of 684). * Running install clean command /usr/lbin/sw/install_clean.NOTE: tlremove is searching filesystem - please be patientNOTE: Successfully completedNOTE: tlinstall is searching filesystem - please be patientNOTE: Successfully completed * Summary of Execution Phase: * 25 of 709 filesets were Skipped. * 684 of 709 filesets had no Errors or Warnings. * The Execution Phase succeeded.= 01/18/06 02:29:07 EST END install AGENT SESSION (pid=138) (jobid=loopback-0001) 第一张盘安装即将结束 * Software installation of this source (B6821 11i Technical Computing OE: CD1) is complete. = USER INTERACTION REQUIRED:To complete the installation you must now insert theB6821 11i Technical Computing OE: CD2 CD. 换盘2，按回车键继续本例中系统盘共3张，故需要进行换盘。当前有些系统是在一张DVD光盘中， 则省去换盘步骤。Once this is done, press the key to continue: * Starting swinstall of the source (B6821 11i Technical Computing OE: CD2). * Running command: /usr/sbin/swinstall -s/tmp/ign_configure/SD_CDROM -f/tmp/ign_configure/software_file -x os_release=B.11.11 -x os_name=HP-UX:64 -xpatch_filter=*.* -xpatch_save_files=true * Installing fileset MLIBPROD.MLIB-MAN,r=B.08.05.01 (151 of 216). * Installing fileset MLIBPROD.MLIB-NOTES,r=B.08.05.01 (152 of 216). * Installing fileset MLIBPROD.MLIB-SCALAPACK,r=B.08.05.01 (153 of 216). * Installing fileset MLIBPROD.MLIB-SLU_DIST,r=B.08.05.01 (154 of 216). * Installing fileset MLIBPROD.MLIB-VECLIB,r=B.08.05.01 (155 of 216). * Installing fileset Mozilla.MOZ-COM,r=1.4.0.01.04 (156 of 216). * Installing fileset Mozilla.MOZ-COM-DOC,r=1.4.0.01.04 (157 of 216). * Installing fileset Mozilla.MOZ-PA11,r=1.4.0.01.04 (158 of 216). * Installing fileset MozillaSrc.MOZ-SRC,r=1.4.0.01.04 (159 of 216). * Installing fileset OE.OE-TECHNICAL,r=B.11.11.0406 (160 of6* Installing fileset VideoOut.VIDEOOUT,r=B.11.00.07.01 (215 of 216). * Installing fileset VideoOut.VIDEOOUT-SHLIB,r=B.11.00.07.01 (216 of 216). * Summary of Execution Phase: * 5 of 221 filesets were Skipped. * 216 of 221 filesets had no Errors or Warnings. * The Execution Phase succeeded.= 01/18/06 02:44:30 EST END install AGENT SESSION (pid=5415) (jobid=loopback-0002) * Software installation of this source (B6821 11i Technical Computing OE: CD2) is complete.= USER INTERACTION REQUIRED:To complete the installation you must now insert the 换盘3，按回车键继续B6821 11i Technical Computing OE: CD3 CD.Once this is done, press the key to continue: * Starting swinstall of the source (B6821 11i Technical Computing OE: CD3). * Running command: /usr/sbin/swinstall -s/tmp/ign_configure/SD_CDROM -f/tmp/ign_configure/software_file -x os_release=B.11.11 -x os_name=HP-UX:64 * Summary of Execution Phase: * 4 of 136 filesets were Skipped. * 132 of 136 filesets had no Errors or Warnings. * The Execution Phase succeeded.= 01/18/06 03:00:02 EST END install AGENT SESSION (pid=11512) (jobid=loopback-0003) 安装完成，系统重启 * Software installation of this source (B6821 11i Technical Computing OE: CD3) is complete.NOTE: tlinstall is searching filesystem - please be patientNOTE: Successfully completed * Loading_software: Complete * Build_Kernel: Begin * Tuned kernel for large swap space: maxswapchunks 2048. * Building a new kernel using the command: /usr/sbin/mk_kernel -o /stand/vmunix.Generating module: krm. /usr/bin/mkdir -p /stand/buildCompiling /stand/build/conf.c.Load