ENONU204i-hUserManual.doc

ONU 204i-h Optical network terminal unitInstallation manualDeclaration 2009 UTStarcom Incorporated. All rights reservedThis manual is to be used by clients, employees of the UTStarcom and those with access granted by UTStarcom, and cannot be copied, reproduced, revised, extracted, reshipped, translated, annotated, sorted, published or disseminated wholly or partly by any unit or individual in any form.UTStarcom, PAS, WACOS, iAN, AIRSTAR, WLL, ISP, WICOPS, NGDLC, Intranode, Internode, Xtr-m-IP, UNITECH, iPATH, !-Volution, mSwitch and小灵通 are registered trademarks of UTStarcom or its subsidiaries. These trademarks are protected by Trademark Law of the Peoples Republic of China, and UTStarcom (China) limited has the right to hold legally accountable any individual or group for illegal use of these trademarks. UTStarcom reserve the right to modify contents of this manual according to product improvement without prior user notification.Please contact the document and information department of UTStarcom for any questions over or discrepancy between this manual and the real product during use. UTStarcom (China) Ltd.Address: No. 368 Liuhe Road (Binjiang), Hi-Tech Industry Development Zone, Hangzhou Post code: 310053Phone: 86-571-81920000Fax: 86-571-81927899Websites: Technical supportUTStarcom applies the perception of “our success based on customer success” to evaluate and normalize employees conduct, and is committed to service innovation and the translation of service commitment, in an effort to perform services surpassing customer expectations. In order to provide efficient technical support and services for our products to guarantee stable running of client systems and equipment, UTStarcoms service department has opened 800 special hotlines to offer our clients professional support and services:800-857-1466 for technical problems800-857-1010 for maintenance issuesBesides, we offer 24*7 hotline services according to clients maintenance contracts and guarantee period, and our senior technical support engineers are committed to making service responses and handling clients problems accordingly. Contact of technical service centerService hotline: 800-857-1466、86-571-88916789Fax: 86-571-88916789E-mail: Website: Address: No. 368 Liuhe Road (Binjiang), Hi-Tech Industry Development Zone, HangzhouPost code: 310053Introduction Version applicable This manual applies to the installation to all ONU 204i-h versionsBrief introduction This manual mainly provides an introduction to the mechanical structure and installation procedures of ONU 204i-h made by UTStarcom, in order to offer normative suggestions and reference data to engineering and technicians for ONU installation and opening.Intended readersIntended readers of this manual mainly are: Engineering installation and maintenance staff Training staffAgreementsTo help readers better the understanding of this manual, some agreements over format, standard and action have been made in this manual as shown in the table below:Format agreement:FormatExplanation Font: Courier NewThings displayed on the terminal screen shall be in Courier New, including configuration files, system output files, commands, such as login.Besides, contents manually input by users, when displayed as system output information, will be in bold type, such as: Password: *.Contained in angular brackets are button names, such as: click button This means that users need to press these keys at the same time; for example, requires users to press Ctrl, Shift and D at the same time.Contained in square brackets are menu items, spreadsheets and field names. For example, / stands for contents of multilevel menu under the Filemenu, like in tool/revise/ compare-merge filewhich refers to selection of compare-merge fileunder the Revisemenu in the main menu of Tool“ ”Radio buttons, check boxes, tabs, listBoxes and windows will all be contained in “”, such as select “Save” tab.Illustration, caution and warning marks:IconsMeaning Interpretation Explanation Annotate or explain current contents, offer more relevant information or supplement current contentsCautionRemind users of special explanation of operations that may affect the systemWarningWarn users of operations that may result in serious consequences, potential dangers and disasters by giving reminding users not to do something or do it with care,Cautions Please read carefully and abide by all matters that need attention as indicated in this manual on the product. When AC power source is available, apply a two-wire single-phase system. The two wires are respectively a live wire and a zero wire, and power connection should be properly earthed. Before installation, check compliance of AC or DC input voltage with rated value and whether the polarity of DC power and grounding are correct. When connecting equipment located at different places, possible potential difference among different grounding wires may damage the equipment or cause performance deviation. Therefore, such potential difference must be eliminated before connection. Please ware an electrostatic ring when plugging, unplugging or touching the circuit since static discharge may damage the equipment. The equipment room should comply with relevant rules in the native country. Never put weight on or walk on the power cable; install protecting plates if necessary. Cooling holes on the frame or stander have been designed to prevent overheating of equipment, and mustnt be covered during running. If the circuit board is to be repaired, symptoms and relevant information must be specified in the guarantee form. Besides, the circuit board should first be put into static screen bag and wrapped in mats before being packaged together with the guarantee form and being returned to the UTStarcom for an overhaul.Contents ContentsIIndex of tablesIIIIndex of illustrationsIV1Overview11.1Product profile12Hardware structure12.1Appearance12.2Indicators12.3Ports22.4Side view33ONU 204i-h installation13.1Package contents13.2Preparation13.3Procedures24WEB configuration4-14.1System information4-14.2System management4-14.3System configuration4-44.3.1ONU configuration4-44.3.2PON configuration4-44.3.3Port configuration4-64.3.4VLAN configuration4-84.4Qos configuration4-94.4.1Algorithm4-94.4.2User priority mapping4-104.4.3DSCP priority mapping4-104.5Multicast configuration4-114.6MAC configuration4-124.7Upgrade4-134.8Restart ONU4-134.9User management4-145Technical parameters5-1AAbbreviationsA-1 Name and content marks of hazardous substancesA-3Index of tablesTable 2-1 ONU 204i-h meaning of indicators2Table 2-2 Port description3Table 5-1 Technical parameters5-1Table 5-2 Ethernet port parameters5-1Table 5-3 Optical port parameters5-2Index of illustrationsFig. 1-1 Network topological diagram1Fig. 2-1 ONU 204i-h front view1Fig. 2-2 ONU 204i-h back view1Fig 2-1 ONU 204i-h front panel indicators2Fig 2-1 ONU 204i-h rear panel ports2Fig 2-1 ONU 204i-h side view3Fig. 3-1 Cable connection diagram2Fig. 3-1ONU 204i-h back view2Fig. 3-1 ONU 204i-h port wiring3Fig. 3-2 ONU 204i-h wiring complete3Fig. 3-2 ONU 204i-h front panel indicators4IVONU 204i-h 光网络终端单元Users manualChapter II Hardware structure1 Overview1.1 Product profileEPON system of UTStarcom provides broadband operators a low-cost fiber access solution. This system is mainly composed of the OLT (optical line terminal) at operators central office and the ONU (optical network unit) at user end. The OLT generates optical fiber signals which are then transmitted, in a descending manner, to each optical fiber port; ONU serves as a remote transmission destination. The optical separator receives an optical signal from the OLT, splits it into multiple uniform signals and then broadcasts them to relevant ONUs each receiving respective optical fiber signals. Optical fiber signals ascending from the ONU end are transmitted in a time-slice method. Transmitter at the ONU end works in a burst mode. Ascending signals and descending signals share the same optical fiber. Length of ascending signal wave: 1310nm, length of descending signal wave: 1490nm. With current signal separating techniques, PON ports of each OLT can support up to 32 terminals (ONU). Using optical fiber, EPON can realize a transmission speed of 1.25Gbps, up to 20km in distance (32 shunts).Fig. 1-1 Network topological diagramInstalled indoors, ONU 204i-h provides four 10/100M Ethernet ports. Configuration and management of ONU 204i-h are realized by OLT of UTStarcom EPON BBS.22 Hardware structure2.1 AppearanceFig. 2-1 ONU 204i-h front viewFig. 2-1 ONU 204i-h front viewFig. 2-2 ONU 204i-h back viewFig. 2-2 ONU 204i-h back view2.2 Indicators0 ONU front panel indicatorsFig 2-1 ONU 204i-h front panel indicators0 meaning of indicatorsTable 2-1 ONU 204i-h meaning of indicatorsLED indicatorsQuantity ColorStatus Explanation PON indicator1GreenOffPower cable not connected or failure of MPCP registration after power cable is connectedOnSuccessful MPCP registration after power cable is connectedAlarm indicator1RedOffPower cable not connected or normal operation after power cable is connectedFlashingFailure of MPCP registration after normal power connection OnONU failure after normal power connectionRUN indicator1GreenOffPower cable not connected or operation fault after power cable is connectedFlashingNormal operation after normal power connection OnOperation fault after normal power connection POWER indicator1GreenOffPower cable not connected OnNormal power connectionLAN1-LAN4 indicator4GreenOffPower cable not connected or unplugged network cable or no link after power cable is connectedFlashingSuccessful pathing link and data transmission after normal power connectionOnSuccessful pathing link after normal power connection2.3 PortsFig 2-1 ONU 204i-h rear panel portsAs indicated in Fig. 2-4, the rear panel of ONU 204i-h has eight ports which, from left, are respectively LAN(1-4), EPON, RESET, power switch and power port. See Table 2-2 for description of these ports.Table 2-2 Port descriptionNoTitle QuantityDescription3-6FE41. Velocity : 10/100M self-adjusting2. Cable: Cat. 53. Connector: RJ-45 ( MDI/MDI-X /AUTO)4. Standard: IEEE802.3、IEEE802.3u2EPON11. SC/PC optical port2. 1.25Gbps3. Optical reception sensitivity: -24.5dBm4. Length of received wave: 1490nm5. Length of transmitted wave: 1310nm 1RESET1ONU 204i-h reset712 V DC112V DC8Power switch1ON/OFF ONU 204i-h power2.4 Side view0 ONU 204i-h side viewFig 2-1 ONU 204i-h side viewThere are 10 cooling holes on each side of ONU 204i-h. 13 ONU 204i-h installationONU 204i-h should be installed indoors.3.1 Package contentsPackage of ONU 204i-h contains: ONU 204i-h, quantity: 1 Power adapter: 1 unit3.2 PreparationDecide a proper position before installing ONU 204i-h. Prepare enough optical fibers and Ethernet cable for all necessary connections 0 ONU 204i-h cable connection diagram.Fig. 3-1 Cable connection diagram3.3 ProceduresStep 1: unpacking of ONU and accessories Make sure all parts indicated in the packing list are in perfect condition.Fig. 3-1ONU 204i-h back viewStep 2: ONU 204i-h installationONU 204i-h can either be laid flat on the table or mounted on the wall. Suppose its laid flat on the table. Four rubber pads are attached to the back of ONU 204i-h to stabilize it on a flat surface. Make sure the device is within the touch of power cable and EPON optical cable. Step 3: ONU 204i-h connection0 Wiring diagram of each ONU 204i-h port.Fig. 3-1 ONU 204i-h port wiringWiring should follow the procedures below:1 Optical cable: Plug optical fiber adapter of the SC cable into the EPON port at the rear panel ONU; this port is SC/PC.2 Power adapter: Plug AC/DC adapter into AC wall jack and ONU 12V DC power jack.3 Ethernet connection: connect RJ-45 Ethernet to any LAN (LAN1-LAN4) port and each family device (i.e. computer or household gateway) of ONU.0 Diagram of completed port wiringFig. 3-2 ONU 204i-h wiring completeStep 6: Check correctness of installation Check connection status through LED displayFig. 3-2 ONU 204i-h front panel indicatorsWhen ONU runs normally after power connection, POWER indicator is normally on with RUN and ALARM indicators flashing. If not, please check the fitness of power adapter and restart ONU. If this problem remains, consider ONU fault.When ONU runs normally after power connection, POWER indicator is normally on. If not, check whether optical fiber of PON port is firmly plugged, make sure the tail optical fiber is not bent or folded and optical power is not too low. If the problem remains, check operators network.4 WEB configuration ONU 204i-h has a built-in Web server which allows for examination of link state and configuration through Web interface.Login: default IP of ONU is . Key into the address bar of the browser and click Enter to enter the login interface. Then input username and password to enter the system (username: admin; password: admin). After entering the system, type of font to be displayed can be selected. 4.1 System information The “system state” interface shows basic information of the equipment, such as equipment model, IP address. (When in other interfaces, lick “system state” in the toolbar to exit to this interface)4.2 System management Flow statisticsAfter entering the system management interface, pull down the “diagnosis” menu in the left of the tool menu and select “flow statistics” to show the interface as indicated above. Ports to be checked can be selected.PON flow:Ethernet interface flow:Timed monitoring:Fill in the desired time of statistics of appointed port, and the list below will show the flow of corresponding port within appointed period of time.4.3 System configuration 4.3.1 ONU configuration Click “advanced configuration” above the toolbar and select “ONU configuration” in the tool menu on the left of the interface to enter the ONU configuration interface where users are allowed to setup MAC address of ONU, etc. To change the IP address, click “static assigned IP” to activate IP input frame to change IP and subnet mask. After configuration, click “apply” and “ok” to confirm the change and click “save” to save the configuration. 4.3.2 PON configuration Encryption: unfold the “PON configuration” menu on the left and select “encryption” to enter PON encryption interface. Then set the encryption mode, click “apply” and “save” to save the configuration. 802.1X certification: unfold “PON configuration” menu on the left and select “802.1X certification” to enter 802.1X certification interface. After setup, click “apply” and “save” to save the configuration. 4.3.3 Port configuration Unfold the “port configuration” menu on the left and select “port configuration” to enter the port configuration interface where port flow control and port work mode can de set up. Click “apply” to confirm the configuration. Port list will then display information of the port (a green link state indicates that the port is connected to PC); click “save” to save the configuration. Port isolate: Unfold the “port configuration” menu on the left and select “port isolate” to enter the port isolate configuration interface. Select “enable isolate” and click “apply” to activate port isolate. Click “save” to save the configuration.Port mirroring: Unfold the “port configuration” menu on the left and select “port mirroring” to enter the port mirroring configuration port. Tick the ports whose input/output needs mirroring and select destination port of mirroring before clicking “apply” to validate mirroring. Click “save” to complete figuration. 4.3.4 VLAN configuration Unfold the “VLAN configuration” menu on the left and select “VLAN configuration” to enter the VLAN configuration interface. After setting the access rule of each port, click “apply” to activate the rules and “save” to save the configuration. VLAN table: Unfold the “VLAN configuration” menu on the left and select “VLAN table” to enter the VLAN table configuration interface to create desired VLAN and add appointed ports to VLAN. “U” as in the “port list” represents member port of untag, “T” member port of tag, “-” non-member port (see instructions). After setting up, click “apply” to check the configuration information and click “save” to save the configuration is everything is ok. 4.4 Qos configuration 4.4.1 AlgorithmUnfold the “Qos configuration” menu on the left and select “algorithm” to enter the Qos algorithm configuration interface where desired algorithm can be set for appointed port. Click “apply” after setting up to check the configuration information and click “save” to save the configuration is everything is ok.4.4.2 User priority mappingUnfold the “Qos configuration” menu on the left and select “user priority mapping” to enter the user priority mapping configuration interface. Set