奥拓福数控超高压水切割机培训(中英)(1)

奥拓福数控超高压水切割机培训,中美合资-沈阳奥拓福科技有限公司,A,B,C,D,E,F,G,: 高压发生器intensifier pump: 数控切割平台CNC cutting table: 数控控制台controller: 自动供砂系统auto feeder system: 软化水处理系统deionization water system: 水循环系统water recycling system:储砂箱abrasive tank,数控超高压水切割机标准配置图,A,B,C,D,E,F,G,H,I,J,K,L,M,N,高压发生器分解图,: 增压器intensifier:蓄能器accumulator:电液换向阀electro hydraulic shift valve:电磁溢流阀electro magnetic overflow valve:电机motor:油泵hydraulic pump:冷却器cooler:油蓄能器oil accumulator:低压水泵low pressure water pump:过滤器water filter:滤油器oil purifier:油压表oil pressure gauge:油温表oil temperature:高压发生器控制开关switch,A,B,E,D,G,H,F,C,:油缸low pressure cylinder:油缸活塞piston assembly:油缸端盖end bell:高压缸HP cylinder:高压缸端螺母end cap:油缸端盖拉杆tie rod :拉杆螺母tie rod nut:磁性开关magnetism sensor switch,增压器分解图,油缸活塞分解图,C,D,E,F,G,H,A,B,:组合密封圈obturating ring assembly:油缸活塞piston:止口垫圈back up ring:型圈O-ring:止口垫圈back up ring:活塞杆压盖spacer:卡簧snap ring :活塞杆ceramic plunger,高压缸分解图,A,F,E,D,C,B,:高压缸HP cylinder:活塞杆导向套seal back up sleeve:O型圈O-ring:高压环seal plunger:高压导环seal/metal hoop:导环垫seal ring,高压缸端螺母分解图,A,E,D,C,B,I,G,H,F,J,K,:高压缸端螺母end cap :高压单向阀outlet check valve body:高压阀芯outlet poppet:塞头阀垫insert:低压水快插接头quick coupling,:塞头check valve main body:低压阀芯inlet poppet:塞头盖inlet check valve support assembly:塞头螺钉retaining screw:O型密圈1 O-seal ring:O型密圈2 O-seal ring,油缸端盖分解图,A,G,F,E,D,C,B,:油缸端盖end bell:磁性开关magnetism sensor switch:O型密封圈 O-seal ring:导向套guide sleeve :Y型圈oil seal:Y型圈挡盖spacer:卡簧snap ring,A,J,I,H,G,F,B,D,E,C,: 蓄能器桶accumulator cylinder:蓄能器端盖end bell:蓄能器塞头check valve main body for accumulator :蓄能器拉杆tie rod:拉杆螺母tie rod nut:密封环seal ring:密封圈垫一seal gasket:密封圈seal ring:密封圈垫二seal gasket:锁紧螺母locknut/seal nut,蓄能器分解图,H,I,J,K,L,A,B,C,D,E,F,G,M,O,P,N,:气缸actuator assembly:压螺retaining cap:密封环seal ring:压环HP valve seal:型圈O-ring:阀针HP valve poppet:水开关阀体valve assembly：刀头支架mounting collar,：水开关阀垫poppet seat：阀垫型圈O-ring：刀头接杆extension tube/nozzle body：能量转换器diamond orifice mount assembly：刀头体abrasive body/mixing chamber：夹管螺母narrow nozzle nut：砂管nozzle/mixing tube：切割防尘罩dust guard,水开关分解图,数控切割平台分解图,：平台基架table pedestal：水槽water tank：隔栅条slat：地脚machine anti-vibration mount：配电箱electric adapter：盖板cover：防尘折布anti-dust shield /dustproof coating：轴x-axis,：砂箱small hopper：自动供砂罐mini hopper：轴Z-axis：水开关on/off valve body：轴Y-axis,数控切割平台分解图,：自动油泵manual pump：轴高压管支架bracket for Y-axis HP tubing：轴高压管支架bracket for X-axis HP tubing：平台气动三联件air filter combination,：梁Y-girder：轴承座pillow block bearing：丝杆ball screw：直线导轨linear guide：同步带timing belt,：伺服电机servo motor：电机支架bracket for motor：同步轮timing belt pulley：溢流管overflow pipe：排水管drain pipe,数控切割平台详细分解图,数控切割平台详细分解图,G,B,C,E,D,F,：电机motor：电机安装座motor bracket：砂罐hopper：控砂阀abrasive valve：气管air hose：输砂管abrasive hose：高压管支架bracket for HP tubing：联轴器shaft joint：丝杆ball screw：轴安装板Z-axis mounted：直线导轨linear guide：轴滑板Z-axis sliding panel：轴升降柱Z-axis lift pole：轴导向座Z-axis guide base：防护罩底托Z-axis panel shield：轴三角铁Z-axis angle iron,控砂阀分解图,：接管adapter：砂阀皮垫gasket：砂阀皮垫gasket：型圈O-ring：螺母nut：砂阀密封gasket垫：节流座throttle,：控砂阀接管gland：焊接式管接头螺母nut：控砂阀三型abrasive valve iii ：压力表pressure gauge：针型阀needle valve：砂阀接头垫gasket：砂阀接头abrasive valve coupling/nipple：型圈O-ring,水切割机水管线连接图,：软化后的高压水deionized HP water source ：自来水源water source：循环水出水管outlet：循环水入水管inlet：增压泵pressurized pump：高压管HP tubing,超高压发生器工作原理,软水器工作原理图解,常用安装及拆卸工具,J,B,C,E,F,H,I,A,D,F,K,L,：蓄能器塞头拆卸工装tool for accumulator check valve main body：阀针安装拆卸工装tool for needle valve：高压环安装拆卸工装tool for HP sealD:橡皮锤rubber malletE:高压缸端螺母安装拆卸扳手wrench for end cap：内六角扳手hex key wrench：螺丝起子screw drive set：活动扳手slip wrench,：钳子slip joint pliers：高度尺leveling rod：水准仪automatic level：小型起重机(地牛)manual pallet truck,动力电接线图解,数控超高压水切割机常用参数说明,超高压发生器 1830 2238 3738最高压力： 300 Mpa 380 Mpa 380 Mpa增压比： 1：19 1：20 1：20最大喷嘴直径： 0.26mm 0.30mm 0.30mm最大排水量： 3.0 L/min 3.7L/min 3.7L/min主电机功率： 18.5KW 22kw 37kw标准电源： 50Hz 380V可订制电源： 50-60Hz 110V / 220V / 380V / 420V,psi是一种压力单位，定义为英镑/平方英寸，145psi=1Mpa 300 Mpa=43500psi 380Mpa=55100psi,切割平台技术参数 驱动方式： 交流伺服最快运行速度： 6000mm/min控制精度： 0.01mm切割精度： 0.1mm电源