压铆螺母尺寸及开孔尺寸

1、实用标准文档文案大全压铆螺母INSJALIATIDN应用于需要封闭罗纹底端的地方。封闭的底端可以限制罗纹穿透并且隔绝外部零件。螺纹规格：#4到1/4和M3到M&BS-832-2 ZI牙型型号牙纹代码板厚代码A最大面板厚 度最小板孔B最大C最大E士 0.10H牙纹L最大T士 0.10碳钢不锈钢.112-401.038.040(#4-40)BBS4402.054.056.166.149.165.250.21.335.38.138-32BBS1.038.040.187.23.335併6-32)6322.054.056.1875.169.275.38.164-321.038.040併8-32)BBS8

2、322.054.056.213.204.212.315.28.385.44.190-32BBS0321.038.040.250.235.249.335.27.385.44(# 10-32)2.054.056.250-20BBS04321.054.056.344.305.343.433.31.500.56(# 1/4-20)2.087.090牙型型号牙纹代码板厚代码A最大面板厚 度最小板孔B最大C最大E士 0.10H牙纹L最大T士 0.10碳钢不锈钢M3X 0.5BBSM310.9714.253.84.226.355.3 8.59.621.371.4M4X 0.7BBSM410.9715.45.

3、25.3887.19.8 11.221.371.4M5X 0.8BBSM510.9716.466.3896.89.8 11.221.37 11.4M6X 1BBSM611.371.48.757.88.72117.812.714.322.212.3压铆螺母Bw-* IS - 44 - a ti I I I*k* CMtiNSTALLATIWAM B和御i占心借卅阳血采用标准工具能快速，便捷的安装：具有良好的抗拉和抗扭性能：用于0.8mm以上的板材,螺纹规格：#2到1/2，M2到M10S-440-2 ZI牙型型号牙纹板厚A面板厚度板孔CET碳钢不锈钢代码代码最大最小最大士 0.01士 0.04.0

4、86-560.030.030SCLS2561.038.040.166.165.25.07併2-56)2.054.056.099-480.030.030SCLS3481.038.040.166.165.25.07併 3-48)2.054.056.112-400.030.030SCLS4401.038.040.166.165.25.07併 4-40)2.054.0563.087.091.138-320.030.030SCLS6321.038.040.1875.187.275.07併6-32)2.054.0563.087.091.164-32併8-32)SCLS8320.030.030.213.21

5、2.315.091.038.0402.054.0563.087.091.190-32(#10-32)SCLS0320.030.030.250.249.354.091.038.0402.054.0563.087.091.216-24(#12-24)SCLS12241.038.040.277.276.374.132.054.0563.087.091.250-20(1/4-20)SCLS04200.045.047.344.343.433.171.054.0562.087.0913.120.125.313-18(5/16-18)SCLS05181.054.056.413.412.50.232.087.

6、0913.120.125.357-16(3/8-16)SCLS06161.087.091.500.499.55.272.120.1253.235.250.500-13(1/2-13)SCLS08131.120.125.656.655.787.362.235.250牙型X螺距型号牙纹代码板厚代码A最大面板厚度最小板孔+0.08C最大E士 0.25T士 0.1碳钢不锈钢M2X0.4SCLSM200.760.8-14.254.226.351.510.97121.371.4M2.5X0.45SCLSM2.500.760.8-14.254.226.351.510.97121.371.4M3X0.5SCL

7、SM300.760.8-14.254.226.351.510.97121.371.4M3.5X0.6SCLSM3.500.760.8-14.754.7371.510.97121.371.4M4X0.7SCLSM400.760.8-15.45.388210.97121.371.4M5X0.8SCLSM500.760.8-16.46.389210.97121.371.4M6X1SCLSM601.151.28.758.72114.0811.371.422.212.3M8X1.25SCLSM61?1.371.410.510.4712.75.4722.212.3M10X1.5SCLSM1012.212.

8、311413.97177.4823.053.18螺母柱300- M3-t Zi j * I z Hwwd L*W F40xh m c q* c* i imAivnai安装于P.C.板上时能使花齿与棉板紧密连接。提供有螺纹和无螺纹式，用于装配间接或叠式 P.C.板。螺纹规格：#4到#6和M3KFE-632-8 ZI英制牙型通孔+0.04-0.03型号牙纹代码长度L+.002/-.005A最大最小板厚板孔+.003C 士 .0 03E士 .005碳钢不锈钢长度代码为1/32英寸.112-40(#4-40)KFEKFSE440.060.060.166.184.218.138-32併6-32)KFEKFSE6324 8 1216 20.060.060.213.231.275.166KFEKFSE116.060.060.166.184.218.143KFEKFSE143.060.060.213.231.275FULL.375 士 .15牙型通孔+0.10-0.08型号牙纹代码长度L+.005/-.013A最大最小板厚板孔+.003