华为交换机配置

1、华为S3526交换机配置命令首先通过配置线连接电脑与交换机的co nsole 口，在电脑上按以下步骤打开超级终端连接交换机：开始-程序-附件-通讯-超级终端连接选择COM口在COM属性对话框中选样属性参散如下Wit选择还原默认值，按确定，即可与交换机交互、视图设置: 接入交换机既进入用户视图，可查看交换机运行状态 system-view 进入系统视图S3526系统视图，可进行系统参数配置S3526 quit返回用户视图二、还原出厂设置：只能在用户视图下 reset saved-co nfigurati on清除交换机配置文件This will delete the configuration

2、in the flash memory.The switch configurations will be erased to reconfigure.Are you sureY/N 输入Y,按回车确认清除交换机配置 reboot 重启交换机This will reboot Switch. Continue Y/N 输入 Y,按回车确认重启三、保存命令： save 只能在用户视图下save保存数据This will save the configuration in the flash memory.The switch configurations will be written to fl

3、ash.Are you sureY/N 输入Y,按回车确认当完成交换机配置后一定要记得 save 保存四、交换机命名 system-view 进入系统视图S3526 sys name BOSS 在系统视图下将交换机名字命名为BOSS五、设置管理 ipBOSS int vlan 1 BOSS-Vlan-interface1 ip address进入 vlan1端口设置管理ipBOSS int vlan 1进入 vlan1端口BOSS-Vlan-interface1 undo ip addressBOSS undo int vlan 1六、查看信息BOSS dis curr#sysname Qui

4、dway#radius scheme systemserver-type huaweiprimary authentication 1645primary accounting 1646 user-name-format without-domaindomain default enable system查看全部配置信息删除管理 vlan 和 iplocal-server nas-ip key huawei#queue-scheduler wrr 1 2 4 8#vlan 1#vlan 25description boss#description cmnet#interface Vlan-in

5、terface1#interface Aux0/0#interface Ethernet0/1description up-to-608port link-type trunkundo port trunk permit vlan 1port trunk permit vlan 18 25 40 101 738 800 995 1042 1116查看端口信息BOSSdis cur int Ethernet 0/2对此端口的描述， 描述为 to 李interface Ethernet0/2 description to lisi 四duplex full此端口双工模式配置为全双工speed 10

6、0 此端口速率配置为 100Mflow-control此端口已配置流量控制port access vlan 2 此端口属于 VLAN 2查看 vlan 信息Quidwaydis vlan allVLAN ID: 1VLAN Type: staticRoute Interface: not configuredDescription: VLAN 0001Name: VLAN 0001Tagged Ports: noneUntagged Ports:Ethernet0/15Ethernet0/16Ethernet0/19Ethernet0/20Ethernet0/21Ethernet0/22Eth

7、ernet0/24Ethernet0/25VLAN ID: 25VLAN Type: staticRoute Interface: not configuredDescription: bossName: VLAN 0025Tagged Ports:Ethernet0/1Untagged Ports:Ethernet0/17 Ethernet0/18BOSS dis vlan 1VLAN ID: 1VLAN Type: staticRoute Interface: not configuredDescription: VLAN 0001Name: VLAN 0001Tagged Ports:

8、noneUntagged Ports:Ethernet0/15Ethernet0/16Ethernet0/19Ethernet0/20Ethernet0/21Ethernet0/22Ethernet0/24Ethernet0/25七、Telnet配置密码认证模式，需要输入 password 登录交换机BOSS user-interface vty 0 4BOSS-ui-vty0-4 authentication-mode password BOSS-ui-vty0-4 set authentication password simple huawei huaweiBOSS-ui-vtyO-4

9、user privilege level 3配置为密码认证模式设置明文密码为设 telnet 权限等级为最高级 3 级配置本地TELNET用户认证模式，需要输入username和password才可以登陆交换机BOSS user-interface vty 0 4BOSS-ui-vty0-4 authentication-mode scheme配置为本地TELNET用户BOSS-ui-vty0-4 quit返回系统视图BOSS local-user boss设置明文密码为 111设 telnet 权限等级为最高建立本地用户，名字为 bossBOSS-luser-boss password si

10、mple 111 BOSS-luser-boss service-type telnet level 3级3级注意：若不是等级 3，可以登录到交换机，但无法对交换机进行配置）设置以上命令后，从电脑连根网线到交换机以太网口（注意：接入的网口必须是属于管理vlan 的，可通过 dis vlan all 查看哪些网口属于管理 vlan ）， 即可通过 telent 管理 交换机， telnet 后需要输入用户名 boss 和密码 111 才可与交换机交互。管理 ip ，用户名和密码可通过 console 口的连接使用 dis cur 命令来查看BOSS dis cur#sysname BOSS#ra

11、dius scheme systemserver-type huaweiprimary authentication 1645primary accounting 1646user-name-format without-domain用户名password simple 111 service-type telnet level 3 #vlan 1description manage-vlanname admin#vlan 2#密码tel net 权限等级vlan 3#interface Vlan-interface1vlan 1ip address管理 ip七、交换机端口配置BOSS int

12、 Ethernet 0/2关闭端口与开启端口BOSS-Ethernet0/2 shutdown进入端口 Ether net 0/2 关闭Ethernet0/2 端口BOSS-Ethernet0/2 undo shutdown重新开启 Ethernet0/2端口local-user boss端口描述BOSS-EthernetO/2 description to lisi对端口进行描述，例如，此端口是连接到李四的电脑上，可描述为 to lisi配置交换机速率与双工模式BOSS-EthernetO/2 speed 设置端口速率10Specify speed of curre nt port 10Mb

13、/s 10M100Specify speed of curre nt port 100Mb/s 100MautoEn able ports speed n egotiati on automatically 自动协商BOSS-Ethernet0/2 duplex 设置端口双工模式autoEn able ports duplex n egotiati on automatically 自动协商fullFull-duplex 全双工halfHalf-duplex 半双工配置端口的链路类型，默认为 access般情况下使用 access交换机级联的端口采用 trunkBOSS-Ethernet0/2

14、 port link-type access Access link-type hybrid Hybrid VLAN link-type trunk VLAN trunk link-type查看全接口状态BOSS dis brief intInterface : EEthernet , G-GigabitEthernet , VlanIF-Vlan-interfaceLink : ADMDOWN-ADMINISTRATIVELY DOWNSpeed : a-auto Duplex : a-autoInterface DescriptionLink Speed Duplex Link-type

15、PVIDPort-typeAux0/0 HUAWEI, Quidway UP - - -E0/1DOWN aa accessE0/2to lisiDOWN100BASE-TXE0/3DOWNaa100BASE-TXE0/4DOWNaa100BASE-TXE0/5DOWNaa100BASE-TXE0/6DOWNa100BASE-TXE0/7DOWNaa100BASE-TXE0/8DOWNaa100BASE-TXa a access 2access 2access 2access 3access 3100BASE-TXa access 3trunk 1E0/21 DOWN a100BASE-TXa

16、 access 1E0/22UPa100M afullaccess1100BASE-TXE0/23DOWN aa access1100BASE-TXE0/24DOWN aa access1100BASE-TX查看全接口配置dis cur int#interface Vlan-interface1 ip address Aux0/0#interface Ethernet0/1#interface Ethernet0/2 description to lisi port access vlan 2 #interface Ethernet0/3port access vlan 2#interface

17、 Ethernet0/4port access vlan 2# interface Ethernet0/5 port access vlan 3# interface Ethernet0/6 port access vlan 3# interface Ethernet0/7 port access vlan 3#interface Ethernet0/8 port link-type trunk port trunk permit vlan all #interface Ethernet0/23#interface Ethernet0/24#查看单个接口配置BOSS-Ethernet0/2 d

18、is cur int e0/2 #interface Ethernet0/2description to lisiport access vlan 2八、交换机VLAN配置首先划分 vlanBOSS vlan 2创建 vlan 2，并进入 vlanBOSS-vlan2 port Ethernet 0/2把端口 0/2 放入 vlan2BOSS-vlan2 port Ethernet 0/3 to Ethernet 0/4把端口 0/3 到 0/4放入 vlan2BOSS vlan 3创建 vlan 3 ，并进入 vlanBOSS-vlan3 port Ethernet 0/5 to Ether

19、net 0/7把端口0/5 到 0/7放入 vlan2接下来把交换机级联端口设为 trunk 模式BOSS int Ethernet 0/8BOSS-Ethernet0/8 port link-type trunkBOSS-Ethernet0/8 port trunk permit vlan all查看 vlanBOSS dis vian all 查看每一个VLAN里包含哪些端口VLAN ID： 1此 VLAN 为 VLAN 1VLAN Type: staticARP proxy disabled.Route Interface： configuredIP Address： Subnet Ma

20、sk： Description： manage-vlanName: adminTagged Ports: noneUntagged Ports:Ethernet0/1Ethernet0/10Ethernet0/12Ethernet0/13Ethernet0/15Ethernet0/16Ethernet0/18Ethernet0/19Ethernet0/21Ethernet0/22Ethernet0/24Ethernet0/8 Ethernet0/9Ethernet0/11Ethernet0/14Ethernet0/17Ethernet0/20Ethernet0/23VLAN ID: 2此 VL

21、AN 为 VLAN 2VLAN Type: staticARP proxy disabled.Route Interface: not configuredDescription: VLAN 0002Name: VLAN 0002Tagged Ports:Ethernet0/8Untagged Ports:Ethernet0/2Ethernet0/3Ethernet0/4VLAN ID: 3此 VLAN 为 VLAN 3EthernetO/7VLAN4VLAN Type: staticARP proxy disabled.Route Interface: not configuredDescr

22、iption: VLAN 0003Name: VLAN 0003Tagged Ports:Ethernet0/8Untagged Ports:Ethernet0/5 Ethernet0/6从 vlan 中删除端口BOSS vlan 3BOSS-vlan3 undo port Ethernet 0/7更改VLAN例如把端口 EthernetO/7 划分到BOSS vlan 4BOSS-vlan4 port Ethernet O/7BOSS dis vlan allVLAN ID: 3VLAN Type: static ARP proxy disabled.Route Interface: not configuredDescription: VLAN 0003 Name: VLAN 0003Tagged Ports:Ethernet0/8Untagged Ports:Ethernet0/5Ethernet0/6VLAN ID: 4VLAN Type: