震雄注塑机规格

1、说明descriptionsunitjm55mk-c射胶部分injection unit射胶量（硬胶）shot weight (ps)oz.2.4gm.69射胶容量swept volumecm380螺杆直径screw diametermm.28射胶压力injection pressurekgf./cm21715螺杆行程screw strokemm.130螺杆转速screw speed ranger.p.m0-140熔胶能力plasticizing capacitykg/hr.40料斗容量hopper capacityl.31射嘴行程nozzle travel strokem.m.220螺杆长度

2、直径比screw l/d ratio19锁模部分clamping unit锁模力clamping forcemp.55开模行程opening strokemm.220连接柱内距（水平×垂直）space between tie bars (h×v)mm.×mm.310×310容模量（最薄-最厚）mould thickness (min-max)mm.80-320模板最大距离maximum daylightmm.540油压顶针推力hydraulic ejector forcemp.2.2油压顶针行程hydraulic ejector strokemm.75定

3、位法兰直径mould register hole (h7)mm.100动力/电热power/heating 油泵马力pump motorkw.(hp)7.5(10)电热量heating capacitykw.4.8系统压力system pressurekfg./cm2145温度控制区no. of temp. control zones2+1其它others循环时间dry cycle timesec.1.6占地面积floor spacem.×m.3×1.2装箱尺寸shipping dimensionm.×m.×m.3.5×1×1.6油缸

4、容量oil tank capacityl.150机重machine weight (dry)ton.2.4说明descriptionsunitjm88mk-c射胶部分injection unit射胶量（硬胶）shot weight (ps)oz.4.5gm.128射胶容量swept volumecm3142螺杆直径screw diametermm.36射胶压力injection pressurekgf./cm21500螺杆行程screw strokemm.140螺杆转速screw speed ranger.p.m10-152熔胶能力plasticizing capacitykg/hr.65料斗

5、容量hopper capacityl.31射嘴行程nozzle travel strokem.m.219螺杆长度直径比screw l/d ratio19锁模部分clamping unit锁模力clamping forcemp.88开模行程opening strokemm.270连接柱内距（水平×垂直）space between tie bars (h×v)mm.×mm.360×360容模量（最薄-最厚）mould thickness (min-max)mm.127-350模板最大距离maximum daylightmm.620油压顶针推力hydrauli

6、c ejector forcemp.3油压顶针行程hydraulic ejector strokemm.75定位法兰直径mould register hole (h7)mm.100动力/电热power/heating 油泵马力pump motorkw.(hp)7.5(10)电热量heating capacitykw.5.6系统压力system pressurekfg./cm2145温度控制区no. of temp. control zones2+1其它others循环时间dry cycle timesec.1.2占地面积floor spacem.×m.3.8×1.3装箱尺寸

7、shipping dimensionm.×m.×m.3.9×1.2×1.7油缸容量oil tank capacityl.150机重machine weight (dry)ton.3.4说明descriptionsunitjm128mk-c射胶部分injection unit射胶量（硬胶）shot weight (ps)oz.9gm.255射胶容量swept volumecm3283螺杆直径screw diametermm.46射胶压力injection pressurekgf./cm21687螺杆行程screw strokemm.170螺杆转速screw

8、 speed ranger.p.m10-200熔胶能力plasticizing capacitykg/hr.100料斗容量hopper capacityl.45射嘴行程nozzle travel strokem.m.280螺杆长度直径比screw l/d ratio20锁模部分clamping unit锁模力clamping forcemp.128开模行程opening strokemm.305连接柱内距（水平×垂直）space between tie bars (h×v)mm.×mm.410×360容模量（最薄-最厚）mould thickness (

9、min-max)mm.175-400模板最大距离maximum daylightmm.705油压顶针推力hydraulic ejector forcemp.3.4油压顶针行程hydraulic ejector strokemm.100定位法兰直径mould register hole (h7)mm.100动力/电热power/heating 油泵马力pump motorkw.(hp)15(20)电热量heating capacitykw.13.4系统压力system pressurekfg./cm2175温度控制区no. of temp. control zones3+1其它others循环时

10、间dry cycle timesec.1.3占地面积floor spacem.×m.4.46×0.98装箱尺寸shipping dimensionm.×m.×m.4.7×1.1×1.6油缸容量oil tank capacityl.300机重machine weight (dry)ton.3.8说明descriptionsunitjm168mk-c射胶部分injection unit射胶量（硬胶）shot weight (ps)oz.14gm.396射胶容量swept volumecm3435螺杆直径screw diametermm.5

11、2射胶压力injection pressurekgf./cm21437螺杆行程screw strokemm.205螺杆转速screw speed ranger.p.m10-150熔胶能力plasticizing capacitykg/hr.110料斗容量hopper capacityl.70射嘴行程nozzle travel strokem.m.300螺杆长度直径比screw l/d ratio20锁模部分clamping unit锁模力clamping forcemp.168开模行程opening strokemm.350连接柱内距（水平×垂直）space between tie

12、bars (h×v)mm.×mm.460×410容模量（最薄-最厚）mould thickness (min-max)mm.220-450模板最大距离maximum daylightmm.800油压顶针推力hydraulic ejector forcemp.4.5油压顶针行程hydraulic ejector strokemm.100定位法兰直径mould register hole (h7)mm.120动力/电热power/heating 油泵马力pump motorkw.(hp)18.75(25)电热量heating capacitykw.16系统压力system pressurekfg./cm2145温度控制区no. of temp. control zones3+1其它others循环时间dry cycle timesec.1.6占地面积floor spacem.×m.4.95×1