KT型可曲挠橡胶接头

1、KXT型可曲挠橡胶接头KXT flexible rubber joi ntPage27材料表 Table of Materials序号SerialNo部位Prti on材料Material1主体Mai n极性橡胶polarizedbodyrubber2内衬Li ning尼龙帘布Nylon cordfabric3L架 I骨架Frame硬钢丝 hard steel wire4法兰Fla nge软钢 Mild steer技术条件 Tech ni cal Con sition型号ModelKXT-( I)KXT-( n)KXT-(川)工作压力 MPa( kg.f/cm2 )Worki ng press

2、ure2.0(20)1.2(12)0.8(8)爆破压力 MPa( kg.f/cm2 )Bursti ng pressure6.0(60)3.5(35)2.4(24)配套法兰 MPa( kg.f/cm2 )support ing flange1.6(16)1.0(10)0.6(6)真空度 Vacuity KPa(mmHg)100(750)86.7(650)53.3(400)适用温度Applecabletemp. °C-20C - 80C （普通型）+80C -135C （特殊配方）适用介质Applecable media空气、压缩空气、水、海水、热水、弱酸Air.Compressed

3、air. Water.Sea Water. Hot Water.Weak acid.Etc接头两端可任意偏转，便于自由调节轴向或横向位移。Both ends of the joi nt ca n be arbitray deflected for freeadjustme nt of axial or lateral displaceme nt.注：DN20C 300KXT- 型工作压力为1.5MPa(15kgf/cm2)爆破压力为4.5MPa(45kgf /cm2)普通型产品只能在 80C以下，如需135C以下需指明，更换橡胶配方，包括耐油、耐酸碱等。压力较高及冲击力较大时宜采用限位拉杆装置

4、。Note: The working pressure of Model DN200 300KXT-(1)is 1.5MPa (15kgf/cm2) and the bursting pressure is 4.5MPa(45kgf/cm2). Ordinary type products can only be used under 80°C if temperature is higher than 135°C, please show clearly . ingredient of the rubber will be changed Restricting pull

5、 rod is necessary . when pressure is high and impulse is great公称通径、长度、位移数值与法兰主要数据表Table of Main Parameters of Nominal Core Diameter， Length，Displacement Value and Flange螺栓孔螺栓孔中心圆横向位螺栓偏转角度公称能径长度数直径直径轴向位移移An gle of安装间距DiameteDiameter ofLateraNominal coreLen gthNo.oAxial dispdeflectioin stallatior ofbo

6、lt holeldiameterl(mm)flace nmen t(mm)nn space < mmboltcen terdisplabolt(a 1 + a 2)holecirclen D1cndo(mm)(mm)eme nt1(mm寸in)伸长Strec h压缩Compression(mm)32(11/4)95417.5100699150440(11/2)95417.51106109150450-2105417.5125710101504(21/21115117.51451150I80-3135130817.5160815121504100-4150135817.5180101913

7、1504125-5165160817.52101219131504150-61801858222401220141505200-81902008222951625221505250-1023024012223501625221506300-1224026012224001625350-1426516224601625400-1626516265151625450-1826520265651625500-202652026620162522222222221506150715071508600-24265700-28260/320800-32260/340900-36260/3701000-40

8、260/4001200-48260/42028203025228243016252282433162522833162522828361625228324118262497251508401009501001050100116010013801001400-56300/4503642159020282610091600-64300/50040481820253530100918005004448202025353010010200055048482230253530100102200-8858052422390253530100102400-9661056422600353010010注：1、

9、表中法兰标准采用 689119PNI.OMPa对应配对法兰应是阀门法兰或符合6B/T9115.1 2000(RF)法兰，安装间距是指软接头法兰与管道上法兰安装后的间隙，并保持均匀一致，以防拉脱。 2 、其他标准或非标准法兰需另订协议，指明标准或提 供图纸及有 关数据，本厂可定制生产。3、公称通经较大时(>700)建议采用大翻边球体产品。4、悬空给水使用DN 200以上产品，管道必须有固 定支撑或固定托架，否则产品应安装防拉脱装置。Note:1 、 FImIge standard is GB9119 PNI.0MPa；TIie matcIfiIN fImge siIotdd be vaIv

10、e fImIge or oiIier fImIges according with GB/T9115.12000(RE)The instaIIation space refers to the gap between soft joint fIange and pipe fIange andit shouId be maintained uniform to avoid puIIing or shedding 3、 For fIanges of other standards or non-standarditis necessary to be agreed upon separateIy pIease speciy standard of furnish diagram and reIative parameter,we wiIImanufacture accordingIy 3、 sphericaI products with wide fIanging are suggested wheninside nominaI diameter is greater than or equaI to 700 4、 Use those products exceeding DN200 w