TL-500C型凸轮轴形面误差综合测量仪

1、TL-500C型凸轮轴形面误差综合测量仪技术协议Technical Protocol of the TL-500C Type Comprehensive Camshaft ProfileSurface Error Measuring Instrument1 .测量原理：该仪器采用极坐标测量原理，由精密滚动主轴系统和高精度光栅编码器生成被 测量凸轮轴回转角度的圆分度，由径向精密滚动导轨和长光栅传感器在径向方向上 扫描凸桃形面每一分度对应的径向凸桃升程，测量评值软件根据被测量凸桃的理论 升程表测量出该凸桃的升程和相位角误差。(原理如图示)1. Measuring PrincipleThis ins

2、trument adopts the pole coordinates measuring principle. The precision rolling main shaft system and the high accuracy encoder generate the round graduation of the measured camshaft turn angle, the radial precision rolling guideway and the linear encoder scan in the radial directionthe radial ascend

3、ing stroke of the peach-shapedc am corresponding to each graduation on the peach-shaped cam profile surface , the measuring and value-evaluation software measures thea scending stroke error and phase angle error of this peach-shapedc am according to the theoretical lift table of the measured peach-s

4、hapedc am. (See the Sketch below.)ter - T测量原理图Sketch of the measuring principle2 .技术指标:可测量凸轮轴轴向长度500 mm测头径向测量行程60 mm主轴回转半径70 mm最大承载重量3 0 Kg测头径向分辨率 0.0001 mm主轴回转分辨率 0.0005 °主轴系下顶尖径向跳0.0015mm动 测量重复性-升程0.003 mm,角度3，升程土示值误差0.003 mm,角度土 5,2. Specifications:Measurable axial length of the camshaft 500

5、mmRadial measuring distance of the measuring head 60mmTurn radius of the main shaft70mmMaximum permissible weight30kgRadial resolution of the measuring head 0.0001mmTurn resolution of the main shaft 0.0005°Radial jumping of the lower center of the main shaft system - 0.0015mmMeasurement repeata

6、bility Ascending stroke 0.003mm, Angle 3，Display value errorAscending stroke 土 0.003mm, Angle ±5,3.结构组成：该仪器采用立式测量结构，被测量凸轮轴垂直安装在主轴和上顶尖之间，因而减重力因素产生的凸轮轴偏心误差。（结构如图示）主机台面：采用花岗岩台面，确保主轴系高精度安装；主轴系：采用高精度密珠滚动轴系、进口海德汉高精度圆光栅、 柔孜电机控制； 测量立柱：采用花岗岩基体' 进口精密直线导轨和滚珠丝杠、封闭式长光栅、 柔孜电机控制；径向测头滑座：采用进口精密滚动导轨' 进口高

7、精度长光栅、柔孜电机控制； 计算机系统：采用国产品牌联想计算机系统（15液晶显示）、激光打印机输出； 测量软件：完全自主知识产权的专业凸轮轴测量分析软件；3. Configuration Constituents:This instrument adopts vertical measurement structure, the measured camshaft is mounted between the main shaft and the upper center vertically to reduce the eccentric error of the camshaft caus

8、ed by the gravity factor. （Configuration is as shown above.）The main unit table : Adopts the granite table to ensure the highly precise installation of the main shaft system;The main shaft system: Adopts high precision dense-ball rolling bearing system, imported HEIDENHAIN high precision encoder and

9、 the RORZE-SANYO motor for control；The measuring column： Adopts granite base, imported precision straight-line guideway, rolling-ball guide screw, sealed linear encoder, and RORZE-SANYO motor for control；The sliding seat of the radial measuring head: Adopts imported precision rolling guideway, impor

10、ted high precision linear encoder and RORZE-SANYO motor for control;The computer system: Adopts China-made Lenovo computer system （15 " LCD）, and laser printer output;The measuring software: Adopts special measuring and analyzing software for camshaft with complete independent intelligent prope

11、rty right.4.测量功能：测量各凸桃的形面误差（升程误差或径向误差）测量各凸桃之间的相位角误 差；测量各凸桃的速度曲线和加速度曲线；测量各凸桃形面的锥度误差；测 量各轴径的径向跳动误差；测量各轴径的圆度误差；桃型对定位键槽相位夹 角；测量软件功能：WINDOWS操作平台的图文交互式中（英）文测量软件；适合各种凸轮轴自动测量的可编程参数描述文件功能：具有相邻轴径和两端轴径修正凸轮轴安装偏 心误差的数据处理功能；可以对刃口测头、球测头测量的桃形进行轮廓线修正 功能；多种测量报告输出方式：用直角坐标和极坐标表示的升程曲线，各凸桃 的速度 曲线和加速度曲线，各凸桃的桃形叠加图（相位图），各凸桃

12、的逐点 升程数据报表;4. Measuring Functions:To measure the peach-shaped cam profile surface of each peach-shaped cam (ascending strokeerror or radial error);To measure thep hase angle error between the peach-shaped cam;To measure the speed curves and acceleration curves of each peach-shaped cam;To measure the

13、 conical error of each peach-shaped cam profile surface ;To measure the radial jumping error of each shaft;To measure the roundness error of each shaft;To measure the phase inclination angle between the peach-shaped cam and the positioning key slot;Functions of the measuring software:Graphic/text in

14、teractive Chinese ( English ) measuring software on the WINDOWS operation platform;Programmable parameter description file function suitable for automatic measurement of various kinds of camshafts;Data processing function to correct eccentric errors caused by camshaft installation from either the ad

15、jacent shafts or the shafts at two ends;The function of revising the contour line of the peach-shaped cam measured by the blade measuring head, the ball measuring head;Multiple output formats for the measurement reports: the ascending stroke curves shown by rectangular coordinates and polar coordina

16、tes, the speed curves and acceleration curves or every peach-shaped cam, the superposed phase charts for every peach-shaped cam, the report sheets of the point-by-point ascending stroke data, etc.5 .仪器标准配置5. Standard Constituents of the Instrument数量QuanMty备注序号No.名称Name1，则量主机 main measuring unit1 台 1

17、 piece2联想计算机系统Lenovo computer system1 套 1 set3联想激光打印机Lenovo laser printer1 台 I piece4主机工作台main unit table1 个 1 piece5计算机工作台computer desk1 个 1 piece6与空制电箱 control box for electrical equipment1 个 1 piece7凸轮轴装卡附件 accessories for camshaft card mounting1 套 1 set6 .仪器技术文件仪器操作使用说明书（含电子版）1份仪器电器原理图、接线表（含电子版）

18、1份计算机随机文件1份仪器装箱单1份仪器合格证 仪器易损件清单及图纸（含电子版） 1份6. Technical Documents AttachedTL-500c型凸轮轴形面误差综合测量仪技术协议-6 -Operation Manual (Including the e-version)1 copyPrinciple sketch and connection table of electrical equipment (Including the e-version)1 copyDocuments along with the computer1copyPacking list1copyQu

19、ality Certificate1copyList and drawings of the easy-damageable par t(slncluding the e-version) 1 copy7. .仪器使用环境温度20 ± 5,相对湿度2 60%,电源220V、50Hz8. Operation ConditionsTemperature： 20± 5°C , Relative humidity 三60%, Power supply: 220V, 50Hz8.验收方式该仪器在需方现场安装，按仪器出厂标准进行现场验收；重复性验收：以用户提 供凸轮轴样件装卡

20、，重复测量5次，其升程和相位误差的测量重复性不超过规定 的要求。示值精度验收：以仪器所带标准样件验收。9. Mode of Check and AcceptanceThe instrument is to be installed on the spot of the user, and to be checked and accepted on the spot according to standards before delivery in the factory.Check and acceptance of repeatability To load the sample camsh

21、aft provided by the user, measure for 5 times repeatedly, the measure repeatability of thaes cending stroke error and the phase error do not exceed the specified requirements.Check and acceptance of the display value: To be completed with the attached standard sample.9.技术培训供方在需方现场安装、验收合格后进行技术培训，培训时间

22、20小时（保证培训需 方2个人学会）。10. Technical TrainingA 20-hour technical training will follow the on-the-spot installation and check and acceptance of the user. （It is guaranteed that 2 persons of the user will be taught to master the operation of the instrument.）10.技术服务（中国）保修期：自交付验收后一年；终身维修：保修期后供方负责终身维护（只收取备件成本和差旅费）。质量承诺：对需方的技术维护响应时限6小时，并48小时内到达用户现场维 护，对小故障24小时修复。11. Technical Servic (e China)Guarantee period: within one year after check and acceptance;Lifelong maintenance: lifelong maintenance after the guarantee period is expired (only costs for spare parts and the business trip are to b