RT射线检测报告样本

1、5焊缝射线检测底片评定表Radiographic film evaluati on form5No.:RT 1503006-04记录编号：DYY/QR-8.2.4-12号:委托单位Trustier丄件名称ProduceDescription材 -WoikpieMfiaf l desig nation 件焊接万法Weld源种类Source type焦点尺寸Focus size增感方式Intensifying Screen像质计型号Type of image quality 显影液配万Developer ingrdint 照相质量等级Photo quality丄件号Produce No焊缝编号We

2、ld No布片张数The number of film焊缝长度mmWeld length板厚 Thickness(mm)透照方式Radiographic Arrangement焦 距Zoom mm一次透照长度mmEffective LengthExa生产部product department 90 弯头 R=1.5D ELBOW 90 LRA/SA403 WP304/304L-WXX-ray1*2.3mmPb箔 (0.03/0.03) FoilFe-m( 10/16)型无锡化冠Wuxi corollaABK-4-81A638单壁单影Single wall510319mination (fcti

3、dSSAgd Procedure Parameter40管电流(活度)mA(Ci) Tubecurrent(Source 曝光时间(min) Exposure time(min) 应识别丝号Should identify wire合格级别(级)Judge level 检测标准Std.for RT1.315工件数量（件）Number产品原编号Products No.规格Size热处理状况State Heat Treatment设备型号X-ray detector model胶片牌号Film brand胶片规格The film size冲洗条件Film Processing显影条件Developi

4、ng Conditions底片黑度Film blackness1503006-0416 SCH10SXXH-2505Agfa-C780 X360 mm手工Manual时间5 min ;温度20 cTime Temperature射线检测位置示意图Drawing2.0-4.02A12765319/14054.1单壁单影Single wall 70015JB/T4730.2-2005要求检测比例%RT%实际检测比例%Carried out RT %检测工艺卡号RT Reguiation100%100%1503006-04A类焊缝(张)Category AWeld (pcs)合格片数heptane

5、30B类焊缝(张)Category BWeld(pcs)相交焊缝（张）Intersect共计(张)Total(pcs)最终评定结果Finaljudge30I级(张)Level I(pcs)30n级(张)Level n(pcs)/皿级(张)Level M (pcs)/IV级(张)Level V (pcs)5检测结果Test results缺陷及返修情况说明Defects and repair51. This batch of workpieces are total 0 repairs. Max. Repair Times is 0 .该批工件返修共计0 次，最高返修次数0次。2. The re

6、pair(s) has (have) been re-examined and can be Acceptable .超标缺陷部位经返修复验合格。3. Please refer to the Radiographic Examination Film Interpretation Sheet for welds for more details about initial1. The workpiece quality comply with the requirements of Executive JB/T4730.2-2005 n standard , the result is qua

7、lified . 该工件质量符合JB/T4730.2-2005 n级标准的要求，结果为合格。2. Please refer to map of Radiographic Examination (attached) and The Radiographic Examination Film Interpretation Sheet for Welds for examination locations and more details.检测位置及底片情况详见射线底片评定表及射线检测位置示意图。5defect.报告人（资格）n：Reporter ( Qualification ) n：审核人（资

8、格）无损检测专用章Examiner ( Qualification ) n：NDT Seal5日期(Date)： 2015-04-01日期(Date)： 2015-04-01日期(Date)： 2015-04-015焊缝射线检测底片评定表Radiographic film evaluati on formNo.: 1503006-04记录编号：DYY/QR-8.2.4-12序号No工件号Produce No焊缝编 号 WeldNo底片编号Film No底片黑度Filmblackness应识别丝号 ShouldRecognit ion Wire板厚 (mm)Thickness缺陷性质及数量Typ

9、e and qty.of defects评定级别Evaluation(level)备注1K-41A12.0-4.0155/I21A22.0-4.0155/I32A12.0-4.0155/I42A22.0-4.0155/I52A32.0-4.0155/I62A42.0-4.0155/I7K-51A12.0-4.0155/I81A22.0-4.0155/I92A12.0-4.0155/I102A22.0-4.0155/I112A32.0-4.0155/I122A42.0-4.0155/I13K-61A12.0-4.0155/I141A22.0-4.0155/I152A12.0-4.0155/I162A22.0-4.0155/I172A32.0-4.0155/I182A42.0-4.0155/I19K-71A12.0-4.0155/I201A22.0-4.0155/I212A12.0-4.0155/I222A22.0-4.0155/I232A32.0-4.0155/I242A42.0-4.0155/I25K-81A12.0-4.0155/I261A22.0-4.0155/I272A12.0-4.0155/I282A22.0-4