Infineon XMC4500 MCU工业应用开发方案_第1页
全文预览已结束

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

1、infineon xmc4500 mcu工业应用开发方案 event request unit (eru) for programmable processing of external and internalservice requests flexible crc engine (fce) for multiple bit error detectionon-chip memories16 kb on-chip boot rom112 kb on-chip high-speed program memory64 kb on-chip high speed data memory32 kb

2、 on-chip high-speed communication1024 kb on-chip flash memory with 4 kb instruction cache communication peripheralsethernet mac module capable of 10/100 mbit/s transfer ratesuniversal serial bus, 2.0 host, full-speed otg, with integrated phycontroller area network interface (multican), full-can/basi

3、c-can with 3 nodes, 64 message objects, data rate up to 1mbit/ssix universal serial interface channels (usic),providing 6 serial channels, usable as uart, double-spi, quad-spi, iic, iis and lin interfacesand touch-sense controller (ledts) for human-machine interfacesd and multi-media card interface

4、(sdmmc) for data storage memory cardsexternal bus interface unit (ebu) enabling communication with external memories and off-chip peripheralsanalog frontend peripheralsfour analog-digital converters (v) of 12-bit resolution, 8 channels each, with input out-of-range comparatorsdelta sigma demodulator

5、 with four channels, digital input stage for a/d signal conversiondigital-analogue converter () with two channels of 12-bit resolution industrial control peripheralstwo capture/compare units 8 (ccu8) for motor control and power conversionfour capture/compare units 4 (ccu4) for use as general purpose

6、 timerstwo position interfaces (posif) for servo motor positioningwindow watchdog timer (wdt) for safety sensitive applicationsdie temperature sensor (dts)real time clock module with alarm supportsystem control unit (scu) for system configuration and controlinput/output linesprogrammable port driver

7、 control module (ports)individual bit addressabilitytri-stated in input modepush/pull or open drain output modeboundary scan test support over jtag interfaceon-chip debug supportfull support for debug features: 8 breakpoints, coresight, tracevarious interfaces: arm-jtag, swd, single wire tracepackag

8、espg-lfbga-144pg-lqfp-144pg-lqfp-100mc4000系列hexagon 应用套件cpu xmc4500通用板cpu_45a-v2cpu board xmc4500 general purpose(cpu_45a-v2)this document describes the features and hardware details of the cpu board xmc4500 general purpose (cpu_45a-v2) designed to work with infineon s xmc4500 microcontroller. this

9、board is part of infineon shexagon application kits.the cpu_45a-v2 board houses the xmc4500 microcontroller and three satellite connectors (hmi, com, act) for application expansion. the board along with satellite cards (e.g. hmi_-v1, com_eth-v1, aut_isov1 boards) demonstrates the capabilities of xmc

10、4500. the main use case for this board is to demonstrate the generic features of xmc4500 device including toolchain. the focus is safe operation under evaluation conditions. the board is not cost optimized and cannot be seen as reference design.通用板cpu_45a-v2主要特性:the cpu_45a-v2 board is equipped with

11、 following featuresxmc4500 (arm cortex -m4) microcontoller, lqfp-144connection to xmc4500 satellite cards via satellite connectors com, hmi and actusb otg host/device support via micro usb connectordebug optionscortex debug connector 10-pin (0.05”)cortex debug+etm connector 20-pin (0.05”)drivemonitor2 stick connectorreset push button32mbit quad spi flash memoryboot from embedded flash, uart or canready for power consumption analysis5 led s3 power indicating led s1 gpio (p3.9) led1 reset ledpotentiometer, connected to a

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论