北京友邦建通测绘仪器销售有限公司

1、DQL-6型光学测树罗盘仪，适用于森林资源调查中的各种测量工作。如距离、高差、 方位、水平、坡角等。同时，可以测定和标定树干任意部位的高度和直径，每公顷胸高断面 积、立木行率、区分求积、造材求积等。也可用于农田水利、土地规划、地形测绘等一般工 程测量。二、主要技术参数望远镜：放大倍率16x磁罗盘:竖直盘:有效孔径视场角视距乘常数视距加常数最短视距磁针长度度盘格值度盘格值游标值测高量程20mm.2° 30'50, 1002m67mm 1 16 ' ± 40m15 72mm1。望远镜组1为 而且在分划板上而且装有与望远镜10m、20m、15m、30m的测高尺 2

2、,在水平距4,可供倾角测量用。为操作方便，备有水准器：圆水准器三、仪器结构仪器主要由望远镜组、竖盘组、罗盘组、安平组四部分组成，见图16倍内调焦式，并可在垂直面内作360度回转，它不仅用来瞄准和测距，没有测径标尺可用来测定树干直径。竖盘组不仅是望远镜的回转轴支架，同步转动的竖直罗盘，盘面上刻有水平距为30m处可测量± 40m高度。盘面下部还刻有角度尺 横轴止动螺旋3和微调螺旋5,可用于精确调整。罗盘组由磁针10和磁针度盘9组成。主要用于磁方位测量，为保证测量精度，罗盘合 上还装有圆形水准器 11。安平机构6是球臼式机构，即可以与三脚架连接， 又可以随意调节， 可迅速方便将仪器 安平。

3、四、使用方法1、基本操作1. 仪器安平将仪器稳固的装置在三脚架上，并使仪器的各可调部位均处中间状态，调整球臼机构使罗盘之园水准器气泡居中。2. 望远镜调节首先旋转目镜视度圈， 使眼睛清晰的看清分划板十字丝，转动仪器使望远镜粗瞄准器大致瞄准目标或标尺，在调节调轮，使之清晰的看清目标。2、方位测量安平仪器，放开磁针止动螺旋 7望远镜十字丝竖丝瞄准目标，待磁针静止后，即 可读取该目标方位。3、距离测量调节望远镜至清晰的看清标尺刻度，读取上、下夹距丝在标尺上所间隔的公分数， 乘以常数50,即得出仪器中心到标尺的距离；如读取上、中两丝或中、下两丝在标尺 上所间隔的公分数，则乘以常数100,即得出仪器中心

4、到标尺的实际距离。在测量时为了读数方便，可以少量转动微调螺旋5，使之其中一横丝处于标尺上公分整数亦可。4、角度测量仪器安平后，调节望远镜通过分划板横丝瞄准被测目标后，可以在竖直度盘的角 度尺上直接读取角度。5、高度测量根据作业和实际需要， 可将仪器安置在水平距为10m、15m、20m、30m任意一点,安平仪器后，用望远镜横丝瞄准被测目标，然后可以在竖直度盘所对应的水平距高度尺上读取其高度（见图 2 a b）-I玉X-1 卜-ra、平地测高时，仰角高度加仪器高度 为总高度。，仪器安平后通过望远镜然后再用望远镜横丝瞄使望远镜分划板上测d则树干上部直径 D6、上部直径测量 将仪器安置于适当水平距离处

5、（根据作业环境任意选定）用常数100观测被测树木的水平距离在分划板上间隔的公分数， 准待测高度部位，并读取所对应的仰角a，在调整水平微调螺旋，径标尺零线对准树干一测，读取树干另一测在测径标尺上的读数S* dD = 可按下式计算：Coss计测实例：图3所示，仪器至树干的水平距离为18m，则在望远镜分划板中读得 S=18cm，仪器瞄准待测高度部位时的仰角a=30° 30'树干在分划板测径标尺上。（如图3）在测量上部直径的同时，亦可在测高尺上读得该部位的高度。五、仪器保养及注意事项仪器出厂前已经过校验， 如仪器经过长途运输、 碰撞、剧烈震动或长期不曾使用时, 在使用时，在使用前应对

6、圆形水准器安平精度进行检查，如有误可通过三个带孔螺 钉8进行校正。仪器使用完毕后，应将磁针锁住以免轴尖磨损。各调整机构应复中间状态，各制动 机构应妥善锁紧。仪器应保存在干燥清洁处，防止各光学件生霉及金属件锈蚀。1、2、3、使用中望远镜光学零件表面应避免污物触及，仪器经维修或拆装后，必须重新校准 后方可使用。六、仪器成套性光学测树罗盘仪4、1、.1台2、.13、三脚架.14、校正针.15、使用说明书6、合格证.1份7、电子计算器（由用户选订的配件套）UseTechnical DataStructureInstructions for usec)measurement of distanced)

7、measurement of anglese) measurement of height11a) preparation for measuringf) measurement of diameterb) azimuthal orientationNoticeUseOptical Compass Model DQL-6 is applicable to surveys in forestry resources. For example, distance, differential altitude, azimuthal orientation, slope angle, tree'

8、;s height or diameter, etc. Besides, it's suitable for agriculture, hydraulic engineering, geology and general engineering. Technical DataTelescope Magnification16xClear object aperture20mmField of view2° 30Stadia multiplication constant50.100Stadia additive constantShortest focusing distan

9、ce2mCompassThe division unit of dialVertical dialThe division unit of dialVernier scale6'Measuring height range± 40mP recision of circular bubble15 72mmWeight1kg12)Size130x100x220(mm)StructureModel DQL-6 is made up of telesc ope, vertical dial, com pass and leveling unit.See Fig1Fig11)2)3)4

10、)5)6)7)8)9)10)11)telesc ope backing-up screw for telesc ope angle's scale slow motion screw for telesc ope height dial eye lensadjusting screw with hole backing-up screw for needle leveling unit horizontal dialneedlecirular bubble Instructi ons for usea) Prep aration for measuringFirst screw the

11、 instrument on the tripod, then adjust the leveling unit for keeping the circular bubble in the center. And all the adjustable parts should bekept in the proper po sition (not in the limit). In measuring, the telesc ope is the main part for taking aim, first adjust the eye lens till the cross hairs

12、can be seen clearly through the eye lens, then adjust the focusing wheel up to the target can be seen clearly, too. In this case, you can begin your work.b)c)Azimuthal orientationFirst release the needle by turning the button for needle and make the vertical line on the reticule pl ate in the same l

13、ine with the target. Well you can get the reading after kee ping the needle still.Measurement of distanceFirst adjust the telesc ope till the scale on the rod can be seen clearly. If you get the reading on the rod between the up line and the down line on the reticule pl ate, the reading must time 50

14、 and this is the distance form instrument to the rod. And if you get the reading on the rod between the middle line and the up line or the domn line, the number must time 100 and this is the distance you wanted. You also can turn the slow motion screw for telesc ope 4 for getting reading easily.d)Me

15、asurement of anglesFirst adjust the telesc ope and make the horizontal line on the reticule pl ate in the same line with the measured target. Then the angle 's degrees can be read straight off the scales of angles scale.e) Measurement of heightPut the instrument at any po int from distance of 10

16、m, 15m, 20m or 30m, then adjust the telescope as in paragraph d) above. Now the height of tree can be got from the height dial.(See Fig 2 a,b)f) Measurement of diameterPut the instrument in the proper po sition that you wanted. First measuring the horizontal distance(s) from instrument to the tree,

17、then measuring the angle of elevation(a). After this turn the slow motion screw 4), as soon as the zero” hir line concides with one sicle of the tree, you can get the number (d) on the horizontal hair line (d is from zero” to the other side of the tree). Well you can count the diameter according to

18、the formula.For example (See Fig3、4) S=18cm a=30 ° 30 d=1.2 then18 X 1.2861629Note: At the same time, you can measure the height of the tree S same part.1.The instrument has been adjusted before leaving factory. PI ease check the circular bubble before using it. If it ' not in the center, you can adjust again with the three adjusting scr