电脑技术员英文自我评价

1、自我鉴定示范文本 | Excellent Model Text 资料编码：CYKJ-FW-328编号：_电脑技术员英文自我评价编辑：_日期：_单位：_电脑技术员英文自我评价用户指南：该自我鉴定资料适用于把阶段时间里取得的成绩、存在的问题及得到的经验和教训进行一次全面系统的总结，明确下一步的工作方向，少走弯路，少犯错误，提高工作效益作用。可通过修改使用，也可以直接沿用本模板进行快速编辑。Since the company in August I was awarded the title of the technician to the present, has been four years

2、time. In these four years, I have been in the operation department, by virtue of their own efforts and leadership to help, from a main duty officer promoted to the duty chief, and was promoted to the post of assistant. During this period, I have our first station of the system have a better understa

3、nding and awareness of some of the various types of accidents have a certain degree of independent analysis and processing capabilities, a technician to do a good job duties .My major in the school of thermal and automation control professional, but in the first station to run our work is most in ne

4、ed of heat, electrical and other aspects of knowledge. This is for me a new challenge, but also the need for continuous learning to improve, so that their professional skills can be fully developed. So, I got some books about these areas, targeted to our system of learning, but also ask some of the

5、old master and professionals, ask them to show up preaching. Through their own efforts and the help of colleagues, finally work pays off, my professional knowledge and professional skills have been greatly improved.But I have a lot of knowledge about the thermal aspects of our system and are particu

6、larly interested in it and have a thorough understanding of it.While at the same time learn from their own, but also assume responsibility for preaching to other operational personnel. Our companys hot water network project is the use of computer monitoring system to achieve hot water production and

7、 operation of the comprehensive monitoring of the data. Its main components include the controller, input and output modules and monitoring stations. Our company has 18 sets of SCAN3000 / S9000 distributed control system (DCS), which has the functions of hot water network operation loop control, dat

8、a acquisition, data communication, centralized information management And operation display functions. It is equipped with two S9000 controllers, and another 12 single-loop controller (Honewell UDC3300), as the control loop redundancy controller and emergency hand terminal. UDC as a backup hand-held

9、 device can DCS in the event of failure, the control loop to control. With easy to operate, programmable, high stability characteristics.DCS system and UDC can achieve between the non-disturbance switch, to ensure the stability of the system operation. S9000 controller through the DVC communication

10、port of the DMC communication circuit and single-loop controller to achieve communication; through the MGTSTA communication port and the system monitoring station communication card connected. With these control systems, usually a variety of parameters of the regulation and personnel labor will have

11、 a multiplier effect. These control systems are made up of measuring elements (temperature transmitters, pressure transmitters, differential pressure transmitters), control elements (S9000, UDC), actuators (regulators, etc.). Control flow is such that the scene collects data from a meter, the transm

12、itter sends 4-20mA signal to the S9000 (that is often said DCS), 1-5V signal to the UDC. And then issued by the S9000 or UDC 4-20mA signal (UDC series with 250 resistor, 1-5V signal to 4-20mA signal) to adjust the actuator. In this process, the instruments power supply from the two Siemens 24V DC po

13、wer supply (the two power supply each other spare), the power to the distributor, and then by the electrical distribution to a primary meter power supply (the middle of electrical distribution in order to meter repair , Will not have a short circuit, and damage the DC power supply). DCS or UDC recei

14、ves the signal that is displayed on the CRT or UDC own screen. DCS or UDC control signal to the impedance converter, distributor, the isolation module or isolated relay relay to the executive control.Isolation module is through the analog signal, that is, continuous control signal 4-20mA, such as th

15、e valve opening, level control; and isolation relay is the switch signal to the DCS, such as temperature switches, pressure switches and pumps Start, stop state, etc. (plus isolation module, isolation relay is to isolate strong signals, so as not to S9000 in the loop control card burned).During the

16、shift, as a monitor, I assume the responsibility of the entire hot water network security and economic operation, the spirit of a high degree of concentration during work, leading the team members carefully adjust the parameters, careful analysis of the data, sum up the law, Found that equipment def

17、ects and risks, to prevent the expansion of the accident. Not only to ensure the safe operation of the hot water network, but also to the economic operation. In some parameters and equipment anomalies, can do a timely analysis, find out the reasons and report, with a certain degree of independent an

18、alysis. Usually go to work, often carefully study a variety of professional knowledge and operating procedures, and can often do a good job in the minds of various accidents expected. In the first station when various types of accidents, can be accurate and decisive for processing and scheduling, and quickly restore the normal operation of the system. During the operation of the Office of the Ministry of Operations, I not only assume the daily operation of the Department of Management, logistics, but also bear the auxiliary operational personnel to make the safe