2012年北京现代名驭ef20原厂维修手册手动变速器系统

1、2012 > G 2.0 DOHC > 手动变速器系统拆卸1. 拆下蓄电池负极。2. 拆下空。3. 拆下空气滤清器。4. 拆开灯开关插头。5. 拆开离合器油管和6. 拆开离合器分泵。7. 拆下车速表软轴。8. 拆下变速杆和变速杆拉线。9. 拆卸起10. 用装配螺栓,并拆下变速器总成的上端装配螺栓。工具支撑发（09200-38100）。汽修一家淘宝：11. 拆下变速器安装支架和橡胶缓冲垫。12. 支撑车辆。13. 拆下前轮胎。14. 拧松放油塞排出变速器油。15. 拆开转向横拉杆球头,下支臂球头和半轴。16. 拆下变速器U形螺栓和回油软管装配螺栓。17. 拆下前排18. 拆下发。架装

2、配螺栓,并拆开发架。19. 拆卸变速器前止动支架。20. 拆卸后侧支架。汽修一家淘宝：21. 拆下变速器侧面装配螺栓。22. 用千斤顶拆卸变速器总成。固定支架安装程序。汽修一家淘宝：1. 发与变速器安装支架的拆解顺序：2. 固定支架安装程序。1) 发支架。2) 变速器支架。3) 后支架。4) 前支架。3. 装配支架时,应避免橡胶缓冲体的损坏,损伤,怠速时产生振动。REMOVAL1. Remove the battery (-) cable.2. Remove the air duct.3. Remove the air cleaner and air flow hose assembly.1.

3、 Disconnect the backup light switch connector.2. Disconnect the clutch tube and clip.3. Remove the clutch release cylinder (Refer to "CH" Group).汽修一家淘宝：1. Disconnect the speedometer sensor connector.2. Remove the select cable and shift cable.1. Remove the starter motor mounting bolts. And

4、remove the upper connecting bolts of the transaxle assembly.2. Attach to the engine hooks using special tool.3. Remove the transaxle mounting bracket and insulator.1. Lift up the vehicle.2. Remove the front tire and the caliper.1. Remove the drain plug and drain the transaxle gear oil.2. Disconnect

5、the tie rod end, lower arm ball joint and drive shaft. (Refer to "DS" Group).汽修一家淘宝：1. Remove the gear box u-joint bolt and the return tube mounting bolts.2. Remove the front muffler.3. Remove the sub-frame mounting bolts and the sub-frame.1. Remove the transaxle front roll stopper.1. Remo

6、ve the rear roll stopper bracket.1. Remove the transaxle side mounting bolts.2. Remove the transaxle assembly supporting by a jack.汽修一家淘宝：When supporting the transaxle assembly, make sure that the lifting force is applied to a wide area, not to a small localized area.1. Engine and transaxle mounting

7、 insulators should be installed the specified torque.2. Mounting bracket installation procedures. Engine mounting bracket. T/M mounting bracket. Rear roll stopper mounting bracket. Front roll stopper mounting bracket.3. Especially, when installing front roll stopper mounting bracket, be careful not

8、to crush the insulator. If crushed, idle vibration will be high.REMOVAL1. Remove the battery (-) cable.2. Remove the air duct.3. Remove the air cleaner and air flow hose assembly.1. Disconnect the backup light switch connector.汽修一家淘宝：2. Disconnect the clutch tube and clip.3. Remove the clutch releas

9、e cylinder (Refer to "CH" Group).1. Disconnect the speedometer sensor connector.2. Remove the select cable and shift cable.1. Remove the starter motor mounting bolts. And remove the upper connecting bolts of the transaxle assembly.2. Attach to the engine hooks using special tool.3. Remove

10、the transaxle mounting bracket and insulator.1. Lift up the vehicle.2. Remove the front tire and the caliper.汽修一家淘宝：1. Remove the drain plug and drain the transaxle gear oil.2. Disconnect the tie rod end, lower arm ball joint and drive shaft. (Refer to "DS" Group).1. Remove the gear box u-

11、joint bolt and the return tube mounting bolts.2. Remove the front muffler.3. Remove the sub-frame mounting bolts and the sub-frame.1. Remove the transaxle front roll stopper.1. Remove the rear roll stopper bracket.1. Remove the transaxle side mounting bolts.汽修一家淘宝：2. Remove the transaxle assembly su

12、pporting by a jack.When supporting the transaxle assembly, make sure that the lifting force is applied to a wide area, not to a small localized area.1. Engine and transaxle mounting insulators should be installed the specified torque.2. Mounting bracket installation procedures. Engine mounting brack

13、et. T/M mounting bracket. Rear roll stopper mounting bracket. Front roll stopper mounting bracket.3. Especially, when installing front roll stopper mounting bracket, be careful not to crush the insulator. If crushed, idle vibration will be high.REMOVAL1. Remove the battery (-) cable.2. Remove the ai

14、r duct.3. Remove the air cleaner and air flow hose assembly.1. Disconnect the backup light switch connector.汽修一家淘宝：2. Disconnect the clutch tube and clip.3. Remove the clutch release cylinder (Refer to "CH" Group).1. Disconnect the speedometer sensor connector.2. Remove the select cable an

15、d shift cable.1. Remove the starter motor mounting bolts. And remove the upper connecting bolts of the transaxle assembly.2. Attach to the engine hooks using special tool.3. Remove the transaxle mounting bracket and insulator.1. Lift up the vehicle.2. Remove the front tire and the caliper.汽修一家淘宝：1.

16、Remove the drain plug and drain the transaxle gear oil.2. Disconnect the tie rod end, lower arm ball joint and drive shaft. (Refer to "DS" Group).1. Remove the gear box u-joint bolt and the return tube mounting bolts.2. Remove the front muffler.3. Remove the sub-frame mounting bolts and th

17、e sub-frame.1. Remove the transaxle front roll stopper.1. Remove the rear roll stopper bracket.1. Remove the transaxle side mounting bolts.汽修一家淘宝：2. Remove the transaxle assembly supporting by a jack.When supporting the transaxle assembly, make sure that the lifting force is applied to a wide area,

18、not to a small localized area.1. Engine and transaxle mounting insulators should be installed the specified torque.2. Mounting bracket installation procedures. Engine mounting bracket. T/M mounting bracket. Rear roll stopper mounting bracket. Front roll stopper mounting bracket.3. Especially, when i

19、nstalling front roll stopper mounting bracket, be careful not to crush the insulator. If crushed, idle vibration will be high.REMOVAL1. Remove the battery (-) cable.2. Remove the air duct.3. Remove the air cleaner and air flow hose assembly.1. Disconnect the backup light switch connector.汽修一家淘宝：2. D

20、isconnect the clutch tube and clip.3. Remove the clutch release cylinder (Refer to "CH" Group).1. Disconnect the speedometer sensor connector.2. Remove the select cable and shift cable.1. Remove the starter motor mounting bolts. And remove the upper connecting bolts of the transaxle assemb

21、ly.2. Attach to the engine hooks using special tool.3. Remove the transaxle mounting bracket and insulator.1. Lift up the vehicle.2. Remove the front tire and the caliper.汽修一家淘宝：1. Remove the drain plug and drain the transaxle gear oil.2. Disconnect the tie rod end, lower arm ball joint and drive sh

22、aft. (Refer to "DS" Group).1. Remove the gear box u-joint bolt and the return tube mounting bolts.2. Remove the front muffler.3. Remove the sub-frame mounting bolts and the sub-frame.1. Remove the transaxle front roll stopper.1. Remove the rear roll stopper bracket.1. Remove the transaxle side mounting bolts.汽修一家淘宝：2. Remove the transaxle assembly supporting by a jack.When supporting the transaxle assembly, make sure that the lifting force is applied to a wide area, not to a small localized area.1. Engine and transaxle mounting insulators should be installed the specified to