OTDR光缆接续测试表测试

1、光缆接续测试表,工程名称：,2015年莆田分公司荔城石顶小镇有线电视网络建设工程,接头点位置：,3号光点接头,纤序,色谱,A端（A1FP02DP001）,B端（2号光点-7号光点）,全程 纤长,全程损耗,接头 衰耗,局端至接头点纤长,全程 纤长,全程损耗,接头 衰耗,用户端至接头点纤长,dB/km,dB,dB/km,dB,填表说明：,1.只要填好黄色区域的数据即可1,蓝,0.123 ,0.225 ,0.028 ,0.04 ,0.056 ,0.123 ,0.220 ,0.027 ,0.02 ,0.067 ,2.波形图下载个PDF打印机，弄好后转成PDF格式2,橙,0.123 ,0.223 ,0.

2、027 ,0.00 ,0.056 ,0.123 ,0.215 ,0.026 ,0.04 ,0.067 ,3.接续表里的数值是动值，因此 接续表最好另表做，做好后粘贴为数值，再把数据拷过来，3,绿,0.123 ,0.229 ,0.028 ,0.04 ,0.056 ,0.123 ,0.219 ,0.027 ,0.02 ,0.067 , 免得变动造成数据对应不上4,棕,0.123 ,0.211 ,0.026 ,0.03 ,0.056 ,0.123 ,0.216 ,0.027 ,0.04 ,0.067 ,4.大芯数光缆以24芯为单位进行编制;小芯数波形图转PDF时注意打印页数5,灰,0.123 ,0.

3、226 ,0.028 ,0.04 ,0.056 ,0.123 ,0.227 ,0.028 ,0.03 ,0.067 ,5.测试波长是按1550nm做的，如有需要用1310nm的，平均损耗公式里的0.21改0.31即可；6,白,0.123 ,0.218 ,0.027 ,0.05 ,0.056 ,0.123 ,0.215 ,0.026 ,0.01 ,0.067 , 当然波形图里的1550 和1.55相应替换成1310和1.31。7,红,0.123 ,0.223 ,0.027 ,0.02 ,0.056 ,0.123 ,0.216 ,0.027 ,0.01 ,0.067 ,8,黑,0.123 ,0.2

4、23 ,0.027 ,0.01 ,0.056 ,0.123 ,0.219 ,0.027 ,0.02 ,0.067 ,9,黄,0.123 ,0.224 ,0.028 ,0.03 ,0.056 ,0.123 ,0.223 ,0.027 ,0.00 ,0.067 ,10,紫,0.123 ,0.224 ,0.028 ,0.02 ,0.056 ,0.123 ,0.212 ,0.026 ,0.02 ,0.067 ,11,粉,0.123 ,0.220 ,0.027 ,0.04 ,0.056 ,0.123 ,0.229 ,0.028 ,0.02 ,0.067 ,12,青,0.123 ,0.217 ,0.027

5、 ,0.02 ,0.056 ,0.123 ,0.221 ,0.027 ,0.05 ,0.067 ,13,蓝,0.123 ,0.216 ,0.027 ,0.02 ,0.123 ,0.221 ,0.027 ,0.03 ,0.123 ,14,橙,0.123 ,0.217 ,0.027 ,0.05 ,0.123 ,0.217 ,0.027 ,0.03 ,0.123 ,15,绿,0.123 ,0.228 ,0.028 ,0.01 ,0.123 ,0.223 ,0.027 ,0.00 ,0.123 ,16,棕,0.123 ,0.220 ,0.027 ,0.05 ,0.123 ,0.213 ,0.026 ,

6、0.03 ,0.123 ,17,灰,0.123 ,0.224 ,0.028 ,0.01 ,0.123 ,0.229 ,0.028 ,0.01 ,0.123 ,18,白,0.123 ,0.213 ,0.026 ,0.01 ,0.123 ,0.211 ,0.026 ,0.00 ,0.123 ,19,红,0.123 ,0.218 ,0.027 ,0.03 ,0.123 ,0.224 ,0.028 ,0.05 ,0.123 ,20,黑,0.123 ,0.226 ,0.028 ,0.02 ,0.123 ,0.213 ,0.026 ,0.04 ,0.123 ,21,黄,0.123 ,0.227 ,0.028 ,0.04 ,0.123 ,0.216 ,0.027 ,0.01 ,0.123 ,22,紫,0.123 ,0.210 ,0.026 ,0.04 ,0.123 ,0.211 ,0.026 ,0.01 ,0.123 ,23,粉,0.123 ,0.214 ,0.026 ,0.03 ,0.123 ,0.217 ,0.027 ,0.00 ,0.123 ,24,青,0.123 ,0.222 ,0.027 ,0.01 ,0.