资料联发MTK专业校准-cfg配置文件2012

1、资料联发_MTK专业校准-cfg配置文件2012META versionMETA version= ver 6.1.08960 Initialization 补偿8960 GPIB Address =GPIB0二15:INSTRTime Out =5000GSM400 cable loss = -1.0GSM850 cable loss = -0.6GSM900 cable loss = -0.6DCS1800 cable loss = -0.8PCS1900 cable loss = -0.8WCDMA BAND1 input cable loss = -1.2WCDMA BAND1 out

2、put cable loss = -1.2WCDMA BAND2 input cable loss = -1.2WCDMA BAND2 output cable loss = -1.2WCDMA BAND5 input cable loss = -0.7WCDMA BAND5 output cable loss = -0.7WCDMA BAND8 input cable loss = -0.7WCDMA BAND8 output cable loss = -0.7CMU200 Initialization 损耗CMU200 GPIB Address =GPIB0:20:INSTRTime Ou

3、t =5000GSM400 input cable loss = 0.7GSM850 input cable loss = 0.6GSM900 input cable loss = 0.6DCS1800 input cable loss = 0.8PCS1900 input cable loss = 0.8GSM400 output cable loss = 0.7GSM850 output cable loss = 0.6GSM900 output cable loss = 0.6DCS1800 output cable loss = 0.8PCS1900 output cable loss

4、 = 0.8WCDMA BAND1 input cable loss = 1.2WCDMA BAND1 output cable loss = 1.2WCDMA BAND2 input cable loss = 1.2WCDMA BAND2 output cable loss = 1.2WCDMA BAND5 input cable loss = 0.7WCDMA BAND5 output cable loss = 0.7Frequency Bank;bank = 0 x1Cbank = 0 x1E 850/900/1800/190颜率;bank = 0 x1A;bank = 0 x0C;GS

5、M450 0 x01;GSM850 0 x02;GSM900 0 x04;DCS1800 0 x08;PCS1900 0 x10C0 for each Bankarfcn_C0_GSM = 659t道arfcn_C0_DCS = 700arfcn_C0_PCS = 660arfcn_C0_GSM850 = 190Downlink powerP_DL = -60AFC Calibration;AFC_BAND: GSM, DCS, PCS, GSM850 AFC_BAND = GSM以900频率校准 AFC_ARFCN = 65 900道N_AFC = 20EXTRA_FB = 5DAC1=35

6、00校准的初始值1DAC2=4500校准的初始值2CRYSTAL_DAC1=3500CRYSTAL_DAC2=4500AFC tableMAX_INIT_AFC_DAC = 6000 A值 MIN_INIT_AFC_DAC = 3000AFC值MAX_AFC_SLOPE = 4.0 AFC最大值 MIN_AFC_SLOPE =2.0 AFC最小值Crystal AFC Calibration晶振/晶体校准;CRYSTAL_AFC_BAND: GSM, DCS, PCS, GSM850 CRYSTAL_AFC_BAND = GSMCRYSTAL_AFC_ARFCN = 65CRYSTAL_AFC

7、_GSM850_PCL = 14CRYSTAL_AFC_GSM900_PCL = 14CRYSTAL_AFC_DCS1800_PCL = 7CRYSTAL_AFC_PCS1900_PCL = 7CRYSTAL_AFC_CAL_DAC = 4096CRYSTAL_AFC_CHECK_DAC1 = 0CRYSTAL_AFC_CHECK_DAC2 = 8191CRYSTAL_AFC_MIN_FREQ_ERR_PPM = -10.0CRYSTAL_AFC_MAX_FREQ_ERR_PPM = 10.0CRYSTAL_AFC_MAX_AFC_TRACK_INIT_FREQ_ERR = 20CRYSTAL

8、_AFC_FREQ_ERR_MEASUSE_COUNT = 10CRYSTAL_AFC_TRX_OFFSET_RECURSIVE_TIMES = 20RX measurement samplesN_PM = 5M_PM = 4RX path loss table接懈GC/补偿校准GSM850_MAX_RX_LOSS =3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.0000,GSM850_MIN_RX_LOSS =-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.00

9、0,-3.000,-3.000,-3.000,-3.000,-高频85GC最大，3.0000,8501GSM900_MAX_RX_LOSS = 3.000,3.000,3.0000,3.000,3.000,3.0000,3.000,3.000,3.0000,3.000,3.000GSM900_MIN_RX_LOSS = -3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.0000,DCS1800_MAX_RX_LOSS = 5.000,5.000,5.0000,5.000,5.000,5

10、.0000,5.000,5.000,5.0000,5.000,5.00DCS1800_MIN_RX_LOSS =-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,PCS1900_MAX_RX_LOSS = 5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000PCS1900_MIN_RX_LOSS =-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000

11、,-5.000,-5.000,-5.000,-5.000,-5.0000,GSM850_MAX_RX_LOSS_MIDDLE =中频AGC最大5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.0000,GSM850_MIN_RX_LOSS_MIDDLE = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,85WGSM900_MAX_RX_LOSS_MIDDLE =5.000,5.000,5

12、.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,GSM900_MIN_RX_LOSS_MIDDLE =-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,DCS1800_MAX_RX_LOSS_MIDDLE =5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,DCS1800_MIN_RX_LOSS_M

13、IDDLE =-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,PCS1900_MAX_RX_LOSS_MIDDLE =5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,PCS1900_MIN_RX_LOSS_MIDDLE =-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000

14、,-5.0000,GSM850_MAX_RX_LOSS_LOW =低频AGC最大，5.0000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.0000,GSM850_MIN_RX_LOSS_LOW =-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-GSM900_MAX_RX_LOSS_LOW =5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0

15、000,5.000,5.000,5.0000,GSM900_MIN_RX_LOSS_LOW = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,DCS1800_MAX_RX_LOSS_LOW =6.000,6.000,6.0000,6.000,6.000,6.0000,6.000,6.000,6.0000,6.000,6.000,6.0000,DCS1800_MIN_RX_LOSS_LOW =-6.000,-6.000,-6.000,-6.000,-6.000,-6.000

16、,-6.000,-6.000,-6.000,-6.000,-6.000,-6.0000,PCS1900_MAX_RX_LOSS_LOW =6.000,6.000,6.0000,6.000,6.000,6.0000,6.000,6.000,6.0000,6.000,6.000,6.0000,PCS1900_MIN_RX_LOSS_LOW =-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.0000,TX IQ tableTX_IQ_MEASUREMENT_COUNT = 20;TX_IQ

17、_BAND: GSM, DCS, PCS, GSM850TX_IQ_BAND = GSMTX_IQ_ARFCN = 65TX_IQ_PCL = 15TX_IQ_DC_OFFSET_MAX = -38TX_IQ_GAIN_IMBALANCE_MAX = -35;The following setting is for MT6140BTX_IQ_BAND_HIGH = DCSTX_IQ_ARFCN_HIGH = 700TX_IQ_PCL_HIGH = 5TX_IQ_DC_OFFSET_MAX_HIGH = -38TX_IQ_GAIN_IMBALANCE_MAX_HIGH = -35TX PCL t

18、able金PC功率校准GSM850_CAL_PCL = 17, 12, 5,GSM850_2CAL_PCL = 19, 5,GSM850_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM850_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM850_MAX_P = 6.5,7.8,9.8,11.8,13.8,15.8,17.8,19.8,21.8,23.8,25.8,27.8,29.8,31.3,32.5,功率GSM850_WANTED_P = 5.0,7.0,9.0,11.0,13

19、.0,15.0,17.0,19.0,21.0,23.0,25.0,27.0,29.0,30.5,32.0,期望功率GSM850_MIN_P = 3.5,6.2,8.2,10.2,12.2,14.2,16.2,18.2,20.2,22.2,24.2,26.2,28.2,29.7,31.5,功率GSM850_C = 12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,GSM850_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,GSM850_EPSK_CAL_PCL = 12, 10, 6,GSM850_EPSK_2

20、CAL_PCL = 19, 5,GSM850_EPSK_4CAL_PCL = 19,14,12,8,GSM850_EPSK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM850_EPSK_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM850_EPSK_MAX_P = 6,8,10,12,14,16,18,20,22,24,26,27.1,27.1,27.1,27.1,GSM850_EPSK_WANTED_P = 5,7,9,11,13,15,17,19,21,23,25,26.5

21、,26.5,26.5,26.5,GSM850_EPSK_MIN_P = 4,6,8,10,12,14,16,18,20,22,24,26,26,26,26,GSM850_EPSK_C = 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,GSM850_EPSK_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,GSM900_CAL_PCL = 17, 12, 5,GSM900_2CAL_PCL = 19, 5,GSM900_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5

22、,GSM900_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM900_MAX_P = 6.5,7.8,9.8,11.8,13.8,15.8,17.8,19.8,21.8,23.8,25.8,27.8,29.8,31.3,32.5,GSM900_WANTED_P = 5.0,7.0,9.0,11.0,13.0,15.0,17.0,19.0,21.0,23.0,25.0,27.0,29.0,30.5,32.0,GSM900_MIN_P = 3.5,6.2,8.2,10.2,12.2,14.2,16.2,18.2,20.2,22.2,2

23、4.2,26.2,28.2,29.7,31.5,GSM900_C = 12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,GSM900_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,GSM900_EPSK_CAL_PCL = 12, 10, 6,GSM900_EPSK_2CAL_PCL = 19, 5,GSM900_EPSK_4CAL_PCL = 19,14,12,8,GSM900_EPSK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM900_EPSK_CH

24、ECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM900_EPSK_MAX_P = 6,8,10,12,14,16,18,20,22,24,26,27.1,27.1,27.1,27.1,GSM900_EPSK_WANTED_P = 5,7,9,11,13,15,17,19,21,23,25,26.5,26.5,26.5,26.5,GSM900_EPSK_MIN_P = 4,6,8,10,12,14,16,18,20,22,24,26,26,26,26,GSM900_EPSK_C = 32,32,32,32,32,32,32,32,32,3

25、2,32,32,32,32,32,32,GSM900_EPSK_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,DCS1800_CAL_PCL = 13, 8, 1,DCS1800_2CAL_PCL = 15, 0,DCS1800_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1800_CHECK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1800_MAX_P = 3.5,4.3,5.8,7.3,8.8,10.8,12.8,14.8,16

26、.8,18.8,20.8,22.8,24.8,26.8,28.3,29.5,DCS1800_WANTED_P = 2.0,3.5,5.0,6.5,8.0,10.0,12.0,14.0,16.0,18.0,20.0,22.0,24.0,26.0,27.5,29.0,DCS1800_MIN_P = 0.5,2.7,4.2,5.7,7.2,9.2,11.2,13.2,15.2,17.2,19.2,21.2,23.2,25.2,26.7,28.5,DCS1800_C = 12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,DCS1800_CORRECTION

27、 = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,DCS1800_EPSK_CAL_PCL = 8, 6, 2,DCS1800_EPSK_2CAL_PCL = 15, 0,DCS1800_EPSK_4CAL_PCL = 15,8,6,2,DCS1800_EPSK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1800_EPSK_CHECK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1800_EPSK_MAX_P = 1,3,5,7,9,11,13,15,1

28、7,19,21,23,25,26.5,26.5,26.5,DCS1800_EPSK_WANTED_P = 0,2,4,6,8,10,12,14,16,18,20,22,24,25.5,25.5,25.5,DCS1800_EPSK_MIN_P = -1,1,3,5,7,9,11,13,15,17,19,21,23,25,25,25,DCS1800_EPSK_C = 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,DCS1800_EPSK_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,PCS1900_CAL

29、_PCL = 13, 8, 1,PCS1900_2CAL_PCL = 15, 0,PCS1900_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,PCS1900_CHECK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1900_MAX_P = 3.5,4.3,5.8,7.3,8.8,10.8,12.8,14.8,16.8,18.8,20.8,22.8,24.8,26.8,28.3,29.5,DCS1900_WANTED_P = 2.0,3.5,5.0,6.5,8.0,10.0,12.0

30、,14.0,16.0,18.0,20.0,22.0,24.0,26.0,27.5,29.0DCS1900_MIN_P = 0.5,2.7,4.2,5.7,7.2,9.2,11.2,13.2,15.2,17.2,19.2,21.2,23.2,25.2,26.7,28.5,PCS1900_C = 12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,PCS1900_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,PCS1900_EPSK_CAL_PCL = 8, 6, 2,PCS1900_EPSK_2CAL_PCL

31、 = 15, 0,PCS1900_EPSK_4CAL_PCL = 15,8,6,2,PCS1900_EPSK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,PCS1900_EPSK_CHECK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,PCS1900_EPSK_MAX_P = 1,3,5,7,9,11,13,15,17,19,21,23,25,26.5,26.5,26.5,PCS1900_EPSK_WANTED_P = 0,2,4,6,8,10,12,14,16,18,20,22,24,

32、25.5,25.5,25.5,PCS1900_EPSK_MIN_P = -1,1,3,5,7,9,11,13,15,17,19,21,23,25,25,25,PCS1900_EPSK_C = 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,PCS1900_EPSK_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,GSM850_SUBBAND_FLATNESS_CHECK_PCL=5GSM900_SUBBAND_FLATNESS_CHECK_PCL=5DCS1800_SUBBAND_FLATNESS_CHE

33、CK_PCL=0PCS1900_SUBBAND_FLATNESS_CHECK_PCL=0GSM850_SUBBAND_FLATNESS_RANGE=0.2GSM900_SUBBAND_FLATNESS_RANEG=0.2DCS1800_SUBBAND_FLATNESS_RANGE=0.2PCS1900_SUBBAND_FLATNESS_RANGE=0.2TXPC_CAL_TEMP=25;check margin;default 900TXPC_GMSK_MAX_APC_DAC=900;default 30TXPC_GMSK_MIN_APC_DAC=30;default 895TXPC_EPSK

34、_MAX_APC_DAC=895;default 192TXPC_EPSK_MIN_APC_DAC=192;default 10 (unit: dB)TXPC_MAX_SUBBAND_COMP=10.0;default -10 (unit: dB)TXPC_MIN_SUBBAND_COMP=-10.0TSC=5Recursive Times=50APC Delta=0.1;for Skyworks 77318, 77328, 77506 only 功放 Skyworks 必须参数SKY77328_DAC_Delta=10SKY77328_GSM850_M = 16.8SKY77328_GSM8

35、50_TARGET_PCL = 19SKY77328_GSM850_MAX_HIGH_APC_DC_OFFSET_P = -3.5SKY77328_GSM850_WANTED_HIGH_APC_DC_OFFSET_P = -4SKY77328_GSM850_MIN_HIGH_APC_DC_OFFSET_P = -4.5SKY77328_GSM850_MAX_LOW_APC_DC_OFFSET_P = -3.5SKY77328_GSM850_WANTED_LOW_APC_DC_OFFSET_P = -4SKY77328_GSM850_MIN_LOW_APC_DC_OFFSET_P = -4.5S

36、KY77328_GSM900_M = 16.8SKY77328_GSM900_TARGET_PCL = 19SKY77328_GSM900_MAX_HIGH_APC_DC_OFFSET_P = -3.5SKY77328_GSM900_WANTED_HIGH_APC_DC_OFFSET_P = -4SKY77328_GSM900_MIN_HIGH_APC_DC_OFFSET_P = -4.5SKY77328_GSM900_MAX_LOW_APC_DC_OFFSET_P = -3.5SKY77328_GSM900_WANTED_LOW_APC_DC_OFFSET_P = -4SKY77328_GS

37、M900_MIN_LOW_APC_DC_OFFSET_P = -4.5SKY77328_DCS1800_M = 17.78SKY77328_DCS1800_TARGET_PCL = 15SKY77328_DCS1800_MAX_HIGH_APC_DC_OFFSET_P = -3.5SKY77328_DCS1800_WANTED_HIGH_APC_DC_OFFSET_P = -4SKY77328_DCS1800_MIN_HIGH_APC_DC_OFFSET_P = -4.5SKY77328_DCS1800_MAX_LOW_APC_DC_OFFSET_P = -3.5SKY77328_DCS180

38、0_WANTED_LOW_APC_DC_OFFSET_P = -4SKY77328_DCS1800_MIN_LOW_APC_DC_OFFSET_P = -4.5SKY77328_PCS1900_M = 17.78SKY77328_PCS1900_TARGET_PCL = 15SKY77328_PCS1900_MAX_HIGH_APC_DC_OFFSET_P = -3.5SKY77328_PCS1900_WANTED_HIGH_APC_DC_OFFSET_P = -4SKY77328_PCS1900_MIN_HIGH_APC_DC_OFFSET_P =-4.5SKY77328_PCS1900_M

39、AX_LOW_APC_DC_OFFSET_P = -3.5SKY77328_PCS1900_WANTED_LOW_APC_DC_OFFSET_P = -4SKY77328_PCS1900_MIN_LOW_APC_DC_OFFSET_P = -4.5MIN_GMSK_GSM850_APC_DAC = 100MIN_GMSK_GSM900_APC_DAC = 100MIN_GMSK_DCS1800_APC_DAC = 80MIN_GMSK_PCS1900_APC_DAC = 80MAX_GMSK_GSM850_APC_DAC = 550MAX_GMSK_GSM900_APC_DAC = 550MA

40、X_GMSK_DCS1800_APC_DAC = 550MAX_GMSK_PCS1900_APC_DAC = 550;MIN_GMSK_GSM850_APC_DAC = 50;MIN_GMSK_GSM900_APC_DAC = 50;MIN_GMSK_DCS1800_APC_DAC = 50;MIN_GMSK_PCS1900_APC_DAC = 50;MAX_GMSK_GSM850_APC_DAC = 550;MAX_GMSK_GSM900_APC_DAC = 550;MAX_GMSK_DCS1800_APC_DAC = 550;MAX_GMSK_PCS1900_APC_DAC = 550;M

41、IN_EPSK_GSM850_APC_DAC = 200;MIN_EPSK_GSM900_APC_DAC = 200;MIN_EPSK_DCS1800_APC_DAC = 200;MIN_EPSK_PCS1900_APC_DAC = 200;MAX_EPSK_GSM850_APC_DAC = 700;MAX_EPSK_GSM900_APC_DAC = 700;MAX_EPSK_DCS1800_APC_DAC = 700;MAX_EPSK_PCS1900_APC_DAC = 700;for FHC onlyFHC_UTS_GMSK_GSM850_MEASURE_SAMPLES = 30FHC_U

42、TS_GMSK_GSM900_MEASURE_SAMPLES = 30FHC_UTS_GMSK_DCS1800_MEASURE_SAMPLES = 30FHC_UTS_GMSK_PCS1900_MEASURE_SAMPLES = 30;FHC_UTS_EPSK_GSM850_MEASURE_SAMPLES = 50;FHC_UTS_EPSK_GSM900_MEASURE_SAMPLES = 50;FHC_UTS_EPSK_DCS1800_MEASURE_SAMPLES = 50;FHC_UTS_EPSK_PCS1900_MEASURE_SAMPLES = 50FHC_UTS_GMSK_MEAS

43、URE_COUNT = 1FHC_UTS_EPSK_MEASURE_COUNT = 1FHC_UTS_GSM850_GMSK_MATH_MODE = 1FHC_UTS_GSM900_GMSK_MATH_MODE = 1FHC_UTS_DCS1800_GMSK_MATH_MODE = 1FHC_UTS_PCS1900_GMSK_MATH_MODE = 1;FHC_UTS_GSM850_EPSK_MATH_MODE = 0;FHC_UTS_GSM900_EPSK_MATH_MODE = 0;FHC_UTS_DCS1800_EPSK_MATH_MODE = 0;FHC_UTS_PCS1900_EPS

44、K_MATH_MODE = 0;FHC_UTS_APC_DAC_MODE = 0FHC_UTS_GMSK_APC_DAC_MODE = 0;FHC_UTS_EPSK_APC_DAC_MODE = 0FHC_UTS_GSM850_GMSK_APC_LOG_SPACE_OFFSET=-60.54;FHC_UTS_GSM850_EPSK_APC_LOG_SPACE_OFFSET_HIGH=1036.13;FHC_UTS_GSM850_EPSK_APC_LOG_SPACE_OFFSET=-376.04FHC_UTS_GSM900_GMSK_APC_LOG_SPACE_OFFSET=-60.54;FHC

45、_UTS_GSM900_EPSK_APC_LOG_SPACE_OFFSET_HIGH=1036.13;FHC_UTS_GSM900_EPSK_APC_LOG_SPACE_OFFSET=-376.04FHC_UTS_DCS1800_GMSK_APC_LOG_SPACE_OFFSET=-74.48;FHC_UTS_DCS1800_EPSK_APC_LOG_SPACE_OFFSET_HIGH=-331.86;FHC_UTS_DCS1800_EPSK_APC_LOG_SPACE_OFFSET=-429.16FHC_UTS_PCS1900_GMSK_APC_LOG_SPACE_OFFSET=-72.44

46、;FHC_UTS_PCS1900_EPSK_APC_LOG_SPACE_OFFSET_HIGH=469.12;FHC_UTS_PCS1900_EPSK_APC_LOG_SPACE_OFFSET=-368.30ADC table ADC电量校准ADC_V1 = 3400 最小电压ADC_V2 = 4200 最大电压ADC_CHECK_VOLTAGE = 3600NORMAL_VOLTAGE = 3900 校准时的电压CURRENT_LIMIT = 3000 电流限制值MAX_BATTERY_ADC_SLOPE = 5650 电量斜率最大值MIN_BATTERY_ADC_SLOPE = 5250

47、电量斜率最小值MAX_BATTERY_ADC_OFFSET = 1000000MIN_BATTERY_ADC_OFFSET = -1000000BATTERY_CHANNEL = 0CHARGER_CHANNEL= 1ADC_RESISTANCE = 0.4MAX_VOLTAGE_DIFFERENCE = 0.04MAX_CURRENT_DIFFERENCE = 0.04ADC_MEASUREMENT_COUNT= 1000以下是引用 tanpeng_wh 在 2008-6-2718:59:30 的发言：校准设置文件以及校准check限制条件（*.CFG文件）： 主要是对手机校准的时候起作用，

48、使得校准按照此文件内的内容去执 行，比如在哪个信道、哪个功率等级，哪种综测仪等等。最后在校准完成以后来重 新 check ,如果一旦超出 check限制条件就算此校准 Fail。功率校准Fail,但是只是相差一点（与限制的范围相差一点），碰到这种情况可以把*.ini中相应频段相应功率等级对应的 Vapc对应的ADC置增加一点就可以了。校准设置文件以及校准check限制条件（*.CFG文件）：主要是对手机校准的时候起作用，使得校准按照此文件内的内容去执行， 比如在哪个信道、哪个功 率等级，哪种综测仪等等。最后在校准完成以后来重新 check,如果一旦超出check限制条件就算此 校准Fail。功

49、率校准Fail,但是只是相差一点（与限制的范围相差一点），碰到这种情况可以把*.ini中相应频段相应功率等级对应的Vapc对应的ADC置增加一点就可以了。br+3 RD 币 是调整VPC的值，就是把ADC的值调大些，让对应的点的输出功率大些。知道什么是功率控制吧?校准文件介利用ATE对手机进行射频和 ADC校准需要用到如下一些文件：NVRAM Database ; Flash的Nvram 区用于存储手机的一些基带和射频参数，Nvram database 相当于定义了这些参数存储的数据结构Setup.ini 例如：CROCODILE_8960_Setup _060914.iniCal.ini 例

50、如：Crocodile Cal 060914.iniCfg.cfg 例如：CROCODILE_CFG _060914.cfgSetup.ini文件是系统设置文件，用于校准终测时对系统测试仪器设置和初始化，包括终测仪， | 电源的GPIP地址，串行通信口，其它相关校准文件的路径，终测时呼叫建立的信道设置，cellpower功率设置，测试项目设置，校准设置，cable loss设置等。Cal.ini文件为手机校准之前的缺省参数，包括射频接收Path loss参数，AFC参数，发射power levelDAC值和ramp profile参数，ADC参数，这些缺省参数在手机校准之前校准程序会先把它写到

51、 手机的NVRAM里面，然后在这些缺省参数的基础上进行校准。其中 ramp profile参数是手机发 射突发脉冲的PvT参数，只是在校准的时候写到手机里面，程序不会对这些参数进行校准，这 些参数在研发的时候会根据PA的类型预先调好。只要 PA是一样的ramp profile参数就是一样的，不同类型的 PA这些参数不一样。Cfg.cfg文件为校准的配置文件，内容包括综测仪GP旧地址和cable loss设置（只有用 META校准的时候才用这些参数，用ATE校准的时候cable loss是在setup.ini文件读取），校准的频段和每个频段用来校准的信道设置，RX path loss的limit

52、范围设置，AFC limit范围设置，发射各个功率等级的目标功率以及limit范围设置，ADC的limit范围设置等。校准结果是Pass还是fail程序就是靠检测校准结果有没有落在cfg文件的limit设置范围内来判断的。4.1INI文件的介绍：；4. 1. 1射频功能组的复位;下面是setupINI文件中 定义的项目；GSM900Sig=1 GSM1800Sig=1 GSM1900Sig=1 GSM900NSig=1 GSM180 0NSig=1; GSM1900NSig=1通常设置为1,指在对CMU20破置之前对设备进；4. 1.2 系统设置：；setupINI文件中定义的项目INI 文件

53、的介绍：4. 1. 1射频功能组的复位下面是setup INI文件中定义的项目。GSM900 Sig = 1GSM1800 Sig = 1GSM1900 Sig = 1GSM900 NSig = 1GSM1800 NSig = 1GSM1900 NSig = 1通常设置为1,指在对CMU20般置之前对设备进行复位，为 0时不复位4.1.2系统设置：setup INI文件中定义的项目:External Reference Clock = 0默认值为0,指使用CMU200J出的参考时钟,为1时使用外部参考时钟。CMU Base GPIB Address = 20CMU勺GPIB地址的设置，要与软件

54、对应。Instrument = CMU200使用的设备为CMU200Power Supply Address = GPIB0:5:INSTR电源地址的设置使用 Kei230 x 时，应为 Power Supply Address = 5CMU RF Port = 2CMU200I用的射频端口设置Test Mode = 0设为0指需要手动对设备进行初始化，1指在综测时软件将自动对设备进行初始 化，2指在校准时软件将自动对设备进行初始化，3指在校准和综测联合测试时软件 将自动对设备进行初始化FDM database file = c:Program FilesMTK_atedemoreportBP

55、LGUInf oCustom Database文件的存放路径，必须与手机软件对应Calibration file = c:Program FilesWMTK_atedemoWMTKCAL_6205B.INI校准初始默认值设置文件的路径Config file = c:Program FilesMTK_atedemometa_6205B.CFG关于校准的设置，如校准的信道，限制的最大、最小值Report file path = c:Program FilesMTK_atedemoreport_6218B测试报告的存储路径Database file = c:Program FilesMTK_ated

56、emoReport_Statistics6218B_statistics.xls测试结果文件的存放路径IMSI = 001010123456789”SIM卡中的IMSI号的设置POWER ON AFTER CHANGE = 1联合测试时，如果设备改变不同状态时较慢，则设置为1Stability Count = 1循环测试的次数设置Fixture COM port = 1串口地址设置System Cable Loss Calibration = 0校准系统的线损选择4. 1. 3呼叫建立设置Setup Network = 1建立呼叫时的网络设置，1指GSM段，2指DCS1段，3指PCS!段GSM

57、 Call Setup Channel = 1建立呼叫的信道号设置GSM BCCH Channel = 32广播控制信道的设置DCS Call Setup Channel = 512DCS!立呼叫的信道设置DCS BCCH Channel = 700DCST播控制信道的设置PCS Call Setup Channel = 512PCS建立呼叫的信道设置PCS BCCH Channel = 700PCS广播控制信道的设置GSM850 Call Setup Channel = 128GSM850t立呼叫的信道设置GSM850 BCCH Channel = 128GSM85CT播控制信道的设置BCC

58、H RF LEVEL = -60下行广播控制信道电平BS TCH LEVEL = -80.5基站业务信道电平Triple Band = 0设置为1时要进行PCS的测试DCS Band = 1为1指综测时要测DCSGSM Band = 1为1指综测时要测GSMGSM850 Band = 0为1时，综测要测GSM850GPRS TEST = 0为1时要进行GPRS勺测试4.1.4信令测试Power Measment Burst = 10定义功率测试时，要测的BurstAverage Burst Power = 1为1指要进行平均功率的测试Peak Burst Power = 1为1指要进行峰值功率

59、的测试PVT Match = 1为1指进行功率时间模板测试Modulation Measment Burst = 10定义调制频谱测试时所要测试的的数量Burst数量Phase Error Peak = 1为1指要进行相位峰值误差的测试Phase Error RMS = 1为1指要进行相位均方值误差的测试Frequency Error = 1为1指要进行频率误差的测试ORFS MOD Burst = 10定义调制频谱测试时，所要测试的 Burst的数量Spectrum Modulation = 1为1指要进行调制频谱的测试ORFS Switch Burst = 10定义开关频谱测试时，所要测试

60、的 Burst的数量Spectrum Switch = 1为1指要进行开关频谱的测试Rx Quality = 0是否进行接收质量的测试RX Level = 0是否进行接收电平的测试RFER = 0是否进行误码率的测试BBB = 0是否进行Bust By Burst的误码率测试GSM Rx Meas Level = -100定义GSM试误码率时的下行功率DCS Rx Meas Level = -100定义DCSM试误码率时的下行功率PCS Rx Meas Level = -100定义PCS测试误码率时的下行功率Rx RFER Burst = 128定义测试时的Burst数量Rx BBB Burs