齐鲁医学Pantoprazole-Sodium-中国药典标准翻译

1、精品医学文档 精品医学文档 3/3精品医学文档 Pantoprazole SodiumC16H14F2N3NaO4SH2O 423.378Pantoprazole Sodium is 5-difluoromethoxy-2-(3,4-dimethoxy-2-pyridinyl)methyl sulfinyl-1H-benzimidazole sodium, monohydrate. It contains not less than 98.0% and not more than 102.0% of C16H14F2N3NaO4S, calculated on anhydrous basis.

2、Description A white or almost white crystalline powder.Freely soluble in water or methanol; practically insoluble in chloroform or diethyl ether. Identification (1) Dissolve 10 mg in 20 ml of water to 2 ml of the resulting solution add 5 drops of dilute hydrochloric acid, then add 1 ml of silicotung

3、stic acid TS dropwise, a white curdy precipitate is produced.(2) The light absorption of a solution of 15 g per ml in ethanol exhibits a maximum at 292 nm, and minimum at 250 nm (Appendix A).(3) The infrared absorption spectrum is concordant with the reference spectrum of pantoprazole sodium (Append

4、ix ).(4) Yields the reaction characteristic of sodium salts (Appendix ). Inspection Alkalinity An aqueous solution of 20 mg per ml, pH 9.5-11.0 (Appendix H). Clarity and colour of solution Dissolve 0.20 g in 10 ml of water, the solution is clear and colourless; any colour produced is not more intens

5、e than that of reference solution Y2 (Appendix A, method 1). Related substances Dissolve a quantity of the product in solvent 0.001 mol/L sodium hydroxide-acetonitrile (1:1) to obtain a solution of 0.4 mg per ml as test solution. Pipet accurately 1 ml of the test solution, to a 100 ml volumetric fla

6、sk, dilute to volume with above solvent, mix well as reference solution. Carry out the method for high performance liquid chromatogrphy (Appendix D). The column is packed with octadecyl silane bonded silica gel, mobile phase A is 0.01 mol/L dipotassium hydrogen phosphate solution (adjust the pH to 7

7、.0 by phosphoric acid), mobile phase B is acetonitrile, gradient elution chromatography is applied as the table below; detection wavelength is 289 nm; column temperature is 40. The number of the theoretical plates calculated from pantoprazole peak is not less than 2500. Inject 20 l of reference solu

8、tion, adjust detection sensitivity so that the peak height of the principle peak in the chromatogram is about 20% of full scale of the chart. Inject separately 20 l of the test solution and the reference solution and record the chromatogram. The area of individual impurity peak is not more than 0.3

9、times of the area (0.3%) of the principle peak in the chromatogram obtained with the reference solution., the sum of the areas of the impurity peaks is not more than 0.8 of the area (for injection) (0.8%) or not more than the area (for oral) (1.0%) of the principle peak in the chromatogram obtained

10、with the reference solution. The area of any peak in the chromatogram of the test solution less than 0.05 times of principle peak area obtained with the reference solution is negligible.Time(min)Flowing phase A (%)Flowing phase B (%)09010306040451585Residual solvents toluene and acetone Transfer 0.2

11、 g of the product, accurately weighted, to a headspace vial, dissolve with 2 ml of water and seal it up as test solution. Measure accurately a properquantity of tuluene and acetone, diluted quantitatively with water to obtain a mixed solution contain about 90 g of toluene and 500 g of acetone per ml

12、(toluene is insoluble in water, dissolve it in DMF first and then disperse in the solvent), measure accurately 2ml of it into a headspace vial, and seal it up as reference solution. Carry out the method for Appendix P, method 2. The column is packed with 5% phenyl-95% polydimenthyl siloxane (or with

13、 similar polarity). Temperature program: initial temperature 40 for 4 minutes, then raise the temperature at a rate of 20 per min to 150 and hold for 3 minutes, the inlet temperature is 200, the detector temperature is 250; the head vial equilibration temperature is 60, equilibration time is 30 minu

14、tes. Inject separately the test preparation and the reference preparation and record the chromatogram. Calculate the quantity by peak area using external standard method, the content of tuluene and acetone shall meet the specification.Water According to method of moisture test (Appendix M Method One

15、), the moisture should be 4.0%6.0%. Heavy metals Transfer 0.5g of the product to a platinum crucible, then slowly Ignite the crucible until the product is the completely carbonized (about4 hours), cool the crucible in a desiccators, Moisten the sample with a small amount (usually 1.21.5mL) of sulfur

16、ic acid, then heat gently at a temperature as low as practicable until the steam of sulfuric acid is wiped off, add 0.5ml of nitric acid, keep heating until the fumes are no longer evolved, then ignite at 500600 until the residue is completely incinerated, cool the crucible. The test is carried out

17、according to Appendix H Method Two, starts from “add 2ml of hydrochloric acid”. The heavy metals should not be more than 20ppm.Content Determination Carry out the method for high performance liquid chromatography (Appendix D). Chromatographic conditions and system suitability The column is packed wi

18、th octadecyl silane bonded silica gel; The mobile phase is 0.01 mol/L dipotassium hydrogen phosphate solution (adjust pH to 7.0 by phosphoric acid) -acetonitrile (65:35). The detection wavelength is 288 nm. The number of the theoretical plate calculated from pantoprazole peak is not less than 2500. Procedure Dissolve