NISSAN 6实验方法及判定条件

1、6. 实验方法及判定条件An appropriate test sample shall be selected or criteria shall be DETERMINATED SO THAT THE FOLLOEING PERFOTMANCE REQUIREMENTS ARE MET FOR ALL OF THE MASS PRODUCTION PARTS为了保证满足量产零件的性能要求，应选择一个合适的样品或确定一个标准。THE NUMBER OF TEST SAMPLES THAT GUARANTEE THE PERFORMANCE REQUIREMETN SHALL BE PRESE

2、NTED应提供保证性能需求的测试样品编号。THE TEST IS CONDUCTED USDING THE PART WHOSE SHAPE IS EQUIVALENT TO THE MATING PART SPECIFIED IN SPECIFICATION TENDERS OR THE MATING PART测试使用的零件形状应与规范招标或结合部件中指定的相同。ALL THE MEASERMENT RESULTS AND MEASUREMENT GRAPHS USED IN TESTING SHALL BE SUBMITTED. THE POINTS THAT HAVE BEEN MEAS

3、URED SHALL BE PLOTTED IN THE GRAPH. 用于测试的所有测量结果和测量图都应提交。所有已测量点应绘制在图中。NO.项目价方法及条件判断标准冲击强度试验（参考原文上的笔记翻译）丄 NO DEFORMATION, CRACK, BREAKAGE THAT AFFECT FUNCTION AT EACH SECTION ARE ALLOWED不能有影响每一段功能的变形、裂纹及破损存在。4- THERE SHALL BE NO ABNORMALITY SUCH AS RUBBER SEPARATION OR CRACKING, NOR DISPLACEMENT, OR T

4、HE LIKE.不得有异常如橡胶分离或开裂，也不能有位移，或类似情况。4- THERE SHALL BE NO ENTANGLEMENT OR DISPLACEMENT OF THE CONT-LEVER BALL WITH RESPECT TO THE SOCKET相对于插座续杠杆球不得有纠缠或位移情况发生。4- AFTER THE TEST, PLEASE REPORTED BY MEASURING THE DEFORMATION AMOUNT FROM THE INITIAL DIMENSIONS AT THE POINT M测试后，请通过测量从最初在点M的尺寸变形量写报告。静态强度试验

5、（参考原文上的笔记翻译）丄 NO DEFORMATION, CRACK, BREAKAGE THAT AFFECT FUNCTION AT EACH SECTION ARE ALLOWED不能有影响每一段功能的变形、裂纹及破损存在。丄 THERE SHALL BE NO ABNORMALITY SUCH AS RUBBER SEPARATION OR CRACKING, NOR DISPLACEMENT, OR THE LIKE.不得有异常如橡胶分离或开裂，也不能有位移，或类似情况。丄 THERE SHALL BE NO ENTANGLEMENT OR DISPLACEMENT OF THE

6、CONT-LEVER BALL WITH RESPECT TO THE SOCKET相对于插座续杠杆球不得有纠缠或位移情况发生。丄 AFTER THE TEST, PLEASE REPORTED BY MEASURING THE DEFORMATION AMOUNT FROM THE INITIAL DIMENSIONS AT THE POINT M测试后，请通过测量从最初在点M的尺寸变形量写报告。(3)疲劳强度及耐热 性能试验（参考原文上的笔记翻译）亠 NO DEFORMATION, CRACK, BREAKAGE THAT AFFECT FUNCTION AT EACH SECTION A

7、RE ALLOWED不能有影响每一段功能的变形、裂纹及破损存在。丄 THERE SHALL BE NO ABNORMALITY SUCH AS RUBBER SEPARATION OR CRACKING, NOR DISPLACEMENT, OR THE LIKE.不得有异常如橡胶分离或开裂，也不能有位移，或类似情况。丄 THE BOOT SHALL NOT BE DISPLACED FROM THE HSG. ALSO, THE MOUNTING LOCA TION OF THE BOOT SHALL NOT BE DISPLACED REMARKABLY.防护罩不应从HSG开始移动，同时，

8、防护罩安装位置 的位移应不明显。丄 AFTER THE TEST, PLEASE REPORTED BY MEASURING THE DEFORMATION AMOUNT FROM THE INITIAL DIMENSIONS AT THE POINT M测试后，请通过测量从最初在点M的尺寸变形量写报告。丄 SHALL BE REPORTED BY MEASURING THE NO-LOAD SLIDING RESISTANCE(BOTH FOR SHIFTING AND FOR SELECTING) BEFORE AND AFTER THE TEST AT THE MEASUREMENT P

9、OINT M POINTS应通 过测量测定点M在试验前后的空载滑行阻力出具报告(换挡和选档测试均如此)。丄 RATE OF CHANGE BEFORE AND AFTER THE TEST THE STIFFNESS V ALUE AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LESS.测定点 M 在试 验前后的刚性值变化率应不咼于15% (换挡和选档测试均如此)。丄 RATE OF CHANGE BEFORE AND AFTER THE AMOUNT OF PLAY

10、 AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LESS.测定点 M 在试验前后的 活动量变化率应不咼于15% (换挡和选档测试均如此)。丄 OPERATION SHALL BE SMOOTH AND WITHOUT TWISTING, SQUEAKING, INTERFERENCE OR THE LIKE THROUGHOUT THE MAXIMUM STROKE OF THE CONTROL LEVER (BOTH FOR SHIFTING AND FOR SEL

11、ECTING).控制杆的最大行程中，操作应平整无扭曲，无异响，无干扰或类似情况(换挡和选档测 试均如此)。丄 THERE SHALL BE NO NOISE BY CONTROL LEVER OPERATION(BOTH FOR SHIFTING AND FOR SELECTING). ALSO IT MUST BE REPORTED BY MEASURING THE VIBRA TION LEVEL BEFORE AND AFTER THE TEST.控制杆操作时不得有噪声(换挡和选档测试均如此)。还必须对测量前后的振动水平出具 报告。亠 AFTER THE TEST, THERE SHAL

12、L BE NO PENETRATION BY WAER INTO THE BOOTS.试验后，不得有 水渗透进防护罩。(4)耐臭氧试验 适用于控制杆防 护罩采用JIS K6259执行丄无裂纹(5)加振耐久性试验 适用于操纵杆组 件，W防护罩（参考原文上的笔记翻译）丄 THERE SHALL BE NO CRACKING, BREAKAGE, LOOSENESS, PLAY OR THE LIKE.不能有变形、裂纹、 松动、活动等类似情况。4- SHALL BE REPORTED BY MEASURING THE NO-LOAD SLIDING RESISTANCE(BOTH FOR SHIFT

13、ING AND FOR SELECTING) BEFORE AND AFTER THE TEST AT THE MEASUREMENT POINT M POINTS应通 过测量测定点M在试验前后的空载滑行阻力出具报告(换挡和选档测试均如此)。4- RATE OF CHANGE BEFORE AND AFTER THE TEST THE STIFFNESS VALUE AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LESS.测定点 M 在试 验前后的刚性值变化率应不咼于

14、15% (换挡和选档测试均如此)。4- RATE OF CHANGE BEFORE AND AFTER THE AMOUNT OF PLAY AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LESS.测定点 M 在试验前后的 活动量变化率应不咼于15% (换挡和选档测试均如此)。4- OPERATION SHALL BE SMOOTH AND WITHOUT TWISTING, SQUEAKING, INTERFERENCE OR THE LIKE THROUGHOUT

15、 THE MAXIMUM STROKE OF THE CONTROL LEVER (BOTH FOR SHIFTING AND FOR SELECTING).控制杆的最大行程中，操作应平整无扭曲，无异响，无干扰或类似情况(换挡和选档测 试均如此)。4- THERE SHALL BE NO NOISE BY CONTROL LEVER OPERATION(BOTH FOR SHIFTING AND FOR SELECTING). ALSO IT MUST BE REPORTED BY MEASURING THE VIBRA TION LEVEL BEFORE AND AFTER THE TEST

16、.控制杆操作时不得有噪声(换挡和选档测试均如此)。还必须对测量前后的振动水平出具 报告。4- AFTER THE TEST, THERE SHALL BE NO PENETRATION BY WJTER INTO THE BOOTS.试验后，不得有 水渗透进防护罩。(6)耐热老化性试验 适用于橡胶件ALLOW THE RUBBER PORTION TO STAND AT A TEMPERATURE OF 100 C FOR30DAYS.THENCONDUCT THE STRENGTH TEST 使橡胶部分在温度 100C环境中矗立30天，然后 进行强度试验。亠 NO DEFORMATION,

17、CRACK, BREAKAGE THAT AFFECT FUNCTION AT EACH SECTION ARE ALLOWED不能有影响每一段功能的变形、裂纹及破损存在。4- THERE SHALL BE NO ABNORMALITY SUCH AS RUBBER SEPARATION OR CRACKING, NOR DISPLACEMENT, OR THE LIKE.不得有异常如橡胶分离或开裂，也不能有位移，或类似情况。4- SHALL BE REPORTED BY MEASURING THE NO-LOAD SLIDING RESISTANCE(BOTH FOR SHIFTING AN

18、D FOR SELECTING) BEFORE AND AFTER THE TEST AT THE MEASUREMENT POINT M POINTS应通 过测量测定点M在试验前后的空载滑行阻力出具报告(换挡和选档测试均如此)。4- RATE OF CHANGE BEFORE AND AFTER THE TEST THE STIFFNESS VALUE AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LESS.测定点 M 在试 验前后的刚性值变化率应不咼于15% (换

19、挡和选档测试均如此)。4- RATE OF CHANGE BEFORE AND AFTER THE AMOUNT OF PLAY AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LESS.测定点 M 在试验前后的 活动量变化率应不咼于15% (换挡和选档测试均如此)。4- OPERATION SHALL BE SMOOTH AND WITHOUT TWISTING, SQUEAKING, INTERFERENCE OR THE LIKE THROUGHOUT THE M

20、AXIMUM STROKE OF THE CONTROL LEVER (BOTH FOR SHIFTING AND FOR SELECTING).控制杆的最大行程中，操作应平整无扭曲，无异响，无干扰或类似情况(换挡和选档测 试均如此)。4- THERE SHALL BE NO NOISE BY CONTROL LEVER OPERATION(BOTH FOR SHIFTING AND FOR SELECTING). ALSO IT MUST BE REPORTED BY MEASURING THE VIBRA TION LEVEL BEFORE AND AFTER THE TEST.控制杆操作

21、时不得有噪声(换挡和选档测试均如此)。还必须对测量前后的振动水平出具 报告。4- AFTER THE TEST, THERE SHALL BE NO PENETRATION BY WJTER INTO THE BOOTS.试验后，不得有 水渗透进防护罩。抗湿性试验 适用于塑料部件CONDUCTINACCORDANCE WITH NESM 0132 N0. 3 METHOD丄 NO DEFORMATION, CRACK, BREAKAGE THAT AFFECT FUNCTION AT EACH SECTION ARE ALLOWED不能有影响每一段功能的变形、裂纹及破损存在。4- SHALL

22、BE REPORTED BY MEASURING THE NO-LOAD SLIDING RESISTANCE(BOTH FOR SHIFTINGTYPE 2. THEN CONDUCT THE STRENGTH TEST.米用NES M 0132方法3类型 2进行。然后进行强度试验。AND FOR SELECTING) BEFORE AND AFTER THE TEST AT THE MEASUREMENT POINT M POINTS应通 过测量测定点M在试验前后的空载滑行阻力出具报告(换挡和选档测试均如此)。4- RATE OF CHANGE BEFORE AND AFTER THE A

23、MOUNT OF PLAY AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LESS.测定点 M 在试验前后的 活动量变化率应不高于15% (换挡和选档测试均如此)。4- OPERATION SHALL BE SMOOTH AND WITHOUT TWISTING, SQUEAKING, INTERFERENCE OR THE LIKE THROUGHOUT THE MAXIMUM STROKE OF THE CONTROL LEVER (BOTH FOR SHIFTI

24、NG AND FOR SELECTING).控制杆的最大行程中，操作应平整无扭曲，无异响，无干扰或类似情况(换挡和选档测 试均如此)。(8)寒冷接触性试验 适用于粘合部位ALLOW THE RUBBER PORTION TO STAND AT A TEMPERATURE OF -40 C FOR30DAYS.THENCONDUCT THE STRENGTH TEST 使橡胶部分在温度 -40C环境中矗立30天，然后 进行强度试验。丄 NO DEFORMATION, CRACK, BREAKAGE THAT AFFECT FUNCTION AT EACH SECTION ARE ALLOWED不

25、能有影响每一段功能的变形、裂纹及破损存在。4- THERE SHALL BE NO ABNORMALITY SUCH AS RUBBER SEPARATION OR CRACKING, NOR DISPLACEMENT, OR THE LIKE.不得有异常如橡胶分离或开裂，也不能有位移，或类似情况。4- RATE OF CHANGE BEFORE AND AFTER THE AMOUNT OF PLAY AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LESS.测定点

26、M 在试验前后的 活动量变化率应不高于15% (换挡和选档测试均如此)。4- OPERATION SHALL BE SMOOTH AND WITHOUT TWISTING, SQUEAKING, INTERFERENCE OR THE LIKE THROUGHOUT THE MAXIMUM STROKE OF THE CONTROL LEVER (BOTH FOR SHIFTING AND FOR SELECTING).控制杆的最大行程中，操作应平整无扭曲，无异响，无干扰或类似情况(换挡和选档测 试均如此)。4- THERE SHALL BE NO NOISE BY CONTROL LEVER

27、 OPERATION(BOTH FOR SHIFTING AND FOR SELECTING). ALSO IT MUST BE REPORTED BY MEASURING THE VIBRA TION LEVEL BEFORE AND AFTER THE TEST.控制杆操作时不得有噪声(换挡和选档测试均如此)。还必须对测量前后的振动水平出具 报告。(9)热循环试验 适用于橡胶及树CONDUCTINACCORDANCE WITH NES亠 NO DEFORMATION, CRACK, BREAKAGE THAT AFFECT FUNCTION AT EACH SECTION ARE ALLO

28、WED不能有影响每一段功能的变形、裂纹及破损存在。脂部件M 0132 N0. 3 METHOD TYPE 2. THEN CONDUCT THE STRENGTH TEST.米用NES M 0132方法3类型 2进行。然后进行强度试验。亠 THERE SHALL BE NO ABNORMALITY SUCH AS RUBBER SEPARATION OR CRACKING, NOR DISPLACEMENT, OR THE LIKE.不得有异常如橡胶分离或开裂，也不能有位移，或类似情况。4- SHALL BE REPORTED BY MEASURING THE NO-LOAD SLIDING

29、RESISTANCE(BOTH FOR SHIFTING AND FOR SELECTING) BEFORE AND AFTER THE TEST AT THE MEASUREMENT POINT M POINTS应通 过测量测定点M在试验前后的空载滑行阻力出具报告(换挡和选档测试均如此)。4- RATE OF CHANGE BEFORE AND AFTER THE TEST THE STIFFNESS VALUE AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LES

30、S.测定点 M 在试 验前后的刚性值变化率应不咼于15% (换挡和选档测试均如此)。4- RATE OF CHANGE BEFORE AND AFTER THE AMOUNT OF PLAY AT THE MEASUREMENT POINT M POINTS (BOTH FOR SHIFTING AND FOR SELECTING) MUST BE 15% OR LESS.测定点 M 在试验前后的 活动量变化率应不咼于15% (换挡和选档测试均如此)。4- OPERATION SHALL BE SMOOTH AND WITHOUT TWISTING, SQUEAKING, INTERFEREN

31、CE OR THE LIKE THROUGHOUT THE MAXIMUM STROKE OF THE CONTROL LEVER (BOTH FOR SHIFTING AND FOR SELECTING).控制杆的最大行程中，操作应平整无扭曲，无异响，无干扰或类似情况(换挡和选档测 试均如此)。4- THERE SHALL BE NO NOISE BY CONTROL LEVER OPERATION(BOTH FOR SHIFTING AND FOR SELECTING). ALSO IT MUST BE REPORTED BY MEASURING THE VIBRA TION LEVEL

32、BEFORE AND AFTER THE TEST.控制杆操作时不得有噪声(换挡和选档测试均如此)。还必须对测量前后的振动水平出具 报告。4- AFTER THE TEST, THERE SHALL BE NO PENETRATION BY WJTER INTO THE BOOTS.试验后，不得有 水渗透进防护罩。(10)抗化学性试验 适用于橡胶及塑 料部件CONDUCTINACCORDANCE WITH NES M 0133 N0. 4 METHOD。采用NES M 0133方法4进 行。丄 THERE SHALL BE NO CRACKING, BREAKAGE, LOOSENESS, PLAY OR THE LIKE.不能有变形、裂纹、 松动、活动等类似情况。4- THERE SHALL BE NO ABNORMALITY SUCH AS RUBBER SEPARATION OR CRA