搅拌器设计选型

反应釜搅拌器的选用反应釜搅拌器的选用：1、根据被搅拌液体容积的大小选用搅拌器的型式。2、根据被搅拌液体的黏度大小选用。3、根据工艺要求的搅拌速度选用，快速搅拌实现液体混合搅拌或形成稳定固体颗粒悬浮液搅拌时应选用涡轮式搅拌器或螺旋桨式搅拌器为宜。4、反应釜容积大于500m3时，采用侧入式，叶轮以螺旋桨式搅拌器为佳。5、根据传热方式考虑，夹套给热以锚式搅拌器为宜；槽内设盘管的给热结构应选用螺旋桨式搅拌器或涡轮式搅拌器。各类搅拌器的使用范围见下表。各种反应釜搅拌器叶轮构形的使用范围表叶轮构形搅拌容量/m3液体黏度/Pa•s叶轮转数/r•min—1流型搅拌的目的螺旋桨搅拌器（直入式）1~400v10100~1750轴向流混合、液相反应、固体悬浮、晶析、传热、溶解螺旋桨搅拌器（侧入式）50~150000v10250~450轴向流混合、传热、防止沉积、均一化斜片桨搅拌器0.1~100v501-100轴向流混合、液相反应、固体悬浮、溶解、分散平桨搅拌器0.1~100v501-100径向流混合、液相反应、溶解、分散涡轮搅拌器0.1~50v501-200径向流混合、液相反应、传热、溶解、分散、气体吸收锚形搅拌器0.1~501-50径向流混合、传热、溶解螺杆搅拌器0.1~5050~5001-50混合、传热、溶解螺带搅拌器0.1~5010~5001-50混合、传热、溶解搅拌装置设计选择＞选择步骤搅拌装置的设计选型与搅拌作业目的紧密结合。各种不同的搅拌过程需要由不同的搅拌装置运行来实现，在设计选型时首先要根据工艺对搅拌作业的目的和要求，确定搅拌器型式、电动机功率、搅拌速度，然后选择减速机、机架、搅拌轴、轴封等各部件。共具体步骤方法如下：.按照工艺条件、搅拌目的和要求，选择搅拌器型式，选择搅拌器型式时应充分掌握搅拌器的动力特性和搅拌器在搅拌过程中所产生的流动状态与各种搅拌目的的因果关系。.按照所确定的搅拌器型式及搅拌器在搅拌过程中所产生的流动状态，工艺对搅拌混合时间、沉降速度、分散度的控制要求，通过实验手段和计算机模拟设计，确定电动机功率、搅拌速度、搅拌器直径。.按照电动机功率、搅拌转速及工艺条件，从减速机选型表中选择确定减速机机型。如果按照实际工作扭矩来选择减速机，则实际工作扭矩应小于减速机许用扭矩。.按照减速机的输出轴头d和搅拌轴系支承方式选择与d相同型号规格的机架、联轴器.按照机架搅拌轴头do尺寸、安装容纳空间及工作压力、工作温度选择轴封型式.按照安装形式和结构要求，设计选择搅拌轴结构型式，并校检其强度、刚度。如按刚性轴设计，在满足强度条件下n/nk<0.7如按柔性轴设计，在满足强度条件下n/nk>=1.3.按照机架的公称心寸DN搅拌轴的搁轴型式及压力等级、选择安装底盖、凸缘底座或凸缘法兰。.按照支承和抗振条件，确定是否配置辅助支承。在以上选型过程中，搅拌装置的组合、配置可参考（搅拌装置设计选择流程示意图），配置过程中各部件之间连接关键尺寸是轴头尺寸，轴头尺寸一致的各部件原则上可互换、组合。设计选择步骤中前二步属搅拌工艺设计范畴，后六步属搅拌结构设计范畴。设计选择时可以参照本公司出版的<<搅拌装置选型图册>>有关内容。如果在搅拌器型式、电动机功率、搅拌速度设计选择方面没有确切数据和把握，请将最基本的工艺条件填写在搅拌装置提资表上，本公司应用工程师将根据所提供的条件为你做出最优化的搅拌装置设计。平直叶PJ、XJ型搅拌器

平直叶与斜叶桨式搅拌器DJ&Be许用扭矩(N.M)重量(kg)平直叶斜叶平直叶斜叶平直叶斜叶平直叶斜叶平直叶斜叶300250843035/6033.430.90.593502808143535/9f5.533.431.10.63400320864035/95.547.81.51.550035010650353"i6057.32.821.655504001086040319195.53.352.260045012860503240101.54.52.5170050012870504410143.56.52.9885055012885554616143.59.23.4395060014895604716248.313.573.9410007001410100705106238219.86.8911008501410100855106250622.311.412009501412120955168050626.715.1513001100141213011052375668.534.618.661400120014121401205237595542.721.3515001400161415014063000114648.938.2160015001614160150635602196.555.546.5170017001614170170635602578.562.558.51800180016161801807356036297273.4J型耀孔J型耀孔2000200018162002007560036298580.52100210018162102107560047759087.92250230020182202308765062071151072500250020182502508904579261501352800280020202802808100719550206158315031502222315315101205011460258230355035502222360255101495014325297280400040002428400400101910019100430400联轴器一TL型弹性套柱销联轴器(GB4323-84)标记示例例1:TL3弹性套柱销联轴器主动轴：Z型轴孔，C型键槽，d3=16mrpL1=30mm从动轴：J型轴孔，B型键槽，d3=18mmL1=130mmTL3联轴ZC16X30GB4323-84器JB18-130例2:HL6弹性套柱销联轴器主动轴：丫型轴孔，A型键槽，d1=40mm,L1=112mm从动轴：丫型轴孔，A型键槽，d1=40mm,L1=112mmTL6联轴器40X112GB4323-84TL型弹性套柱销联轴器主要尺寸T■弹性套柱箱联轴器表3-7标准符号许用扭矩许用转速轴径直径轴孔长度DSA重量铁钢铁钢LL1(N.m)(r/min)(mm)kgTL16.36600880092014713181.1610、1125171212、143220TL2165500760012、14801.641616、18、194230TL331.54700630016、18、19954351.92020、225238TL4634200570020、22、241062.3一25、286244TL51253600460025、281305458.3630、3230、32、358260TL62503300380032、35、3816010.364040、4211284TL75002800360040、42、4519015.6一48TL87102400300045、48、50、5522466525.456一60、42142107TL910002100285050、55、561128425030.960、63142107一65、70、71TL1020001700230063、65、70、71、7531588065.980、8580、85、90、95172132TL1140001350180080、85、90、9517213240010100122.6100、110212167TL12800011001450100、110、120、12547512130218.4一130252202TL13160008001150120、12521216760014180425.8联轴器-HL型弹性套柱销联轴器（GB5014-85标记示例例1:HL6弹性套柱销联轴器N例1:HL6弹性套柱销联轴器N型轴孔）、二主动轴：丫型轴孔，A型键槽，d1=65mrpL1=142mm从动轴：丫型轴孔，A型键槽，d2=65mrpL1=142mmHL6联轴器65X142GB5014-85例2:HL7弹性柱销联轴器主动轴：Z型轴孔，C型键槽，d3=75mm,L1=107mm从动轴：J型轴孔，B型键槽，d2=70mm,L1=107mmHL7联轴ZC75X107GB5014-85器JB70X107标定符号许用扭矩许用转数轴径直径d1、d2、d3轴孔长度DS重量铁钢铁钢LL1(N.m)(r/min)(mm)kgHL1160710012、143227902.5216、18、19423020、2220、22、245238HL2315560020、22、2452331202.5525、28624430、3230、32、358260HL3630500030、32、35、38160840、4240、42、45、4811284HL41250400040、42、45、48、50、55、56195322-60、63142107HL52000355055、56、60、63、65、7022030-71、75HL63150280060、63、65、70、71、75、80280453-85172132HL76300224070、71、751421073209880、85、90、95172132100100、110212167HL810000212080、85、90、95、100、1103605119-120、125HL9160001800100、110、120、125410197130130、140252202HL10250001560110、120、125130、140、1502122521672024806322160160、170、180302242HL11315001320130、140、150252202540520160、170、180302242190190、200、220353282HL型弹性柱销联轴器主要尺寸表3-8

HL1263001250160、170、1803022426307714190、200、220352282240、250、260410330190、200、220352282HL131000001120240、250、26041033071010571280、3004703808HL14100000850240、250、2604103308001956联轴器-JQ型夹壳联轴器(HG21570-95)1、JQ型夹壳联轴器适用于立式减速机l型轴伸与反应罐搅拌轴伸的联接。2、按立式减速机的l型轴伸直径选择相对应的JQ型轴径。JQ型夹壳联轴器(HG21570-95)表3-1

标定符号孔径dgMmaxN.MDLL1H8/j7L2L3n-dod1H11/h11d2Hi1la1H11b11112Rfbtt1重量kgJQ-2525901021302055644-1438205445600.20.4828.3214.47JQ-3030901021302055644-1438255445700.20.4833.3254.47JQ-35352361181622071806-1443305455850.40.61038.3307.60JQ-40402361181622071806-1448355455850.40.61243.3357.60JQ-45455301351902483946-14573765701000.40.61448.839.510.85JQ-50505301351902483946-14624265701000.40.61453.844.510.85JQ-55555301351902483946-14674765701300.611659.34910.85JQ-60601400172250301101248-187350861001300.611864.45325.06JQ-65651400172250301101248-188355861001300.611869.457.525.06JQ-70701400172250301101248-188360861001450.612074.962.525.06JQ-80802650185250381211388-1894701081101450.612285.47130.16JQ-85852650185280381211388-2399751081101700.612290.47630.16JQ-90905200230330381461648-23105801081401700.612595.48156.38JQ-95955200230330381461648-23110851081401700.6125100.48656.38JQ-1001005200230330381461648-23115901081401700.6128106.49056.38JQ-1051055200230330381461648-23120951081402000.6128111.49556.38JQ-1101109000260390461721908-2312510012101602000.6128116.410090JQ-1151159000260390461721908-2313010512101602000.6132122.410490JQ-1201209000260390461721908-2313511012101602250.6132127.410990JQ-125125150002804405419321010-2314011514121802250.6132132.4114125JQ-130130150002804405419321010-2314611814121802250.6132137.4119125JQ-140140150003004405419323010-2315812814121802550.6136148.4128125JQ-150150280003405006421826010-3317913416142002550.6136158.4138215JQ-160160280003405006421826010-3318014416142002550.6140169.4147215JQ-180180310003805607224430010-33200162181624028511.545190.4165350JQ-200200337504206408028034010-13220182201827032511.545210.4185516机械密封

机械密封径向接触式轴封，适用于压力2.5Mp压力以下要求轴的密封，结构复杂，对轴的光洁度及饶212型单端面波纹管机械密封79标准安装尺寸代号212-30212-40212-50212-60212-65212-70212-80212-90212-95212-100212-110212-120212-130212-140212-1规格d304050606570809095100110120130140150D160185205235290320360D1130150170200255280320D2788798110115120130140145150162172182192201D36072809095100110120125130140150162172

D47188101106116121131141151156166171178188n-①4-0144-①188-①1812-①18H200220Dx(F4)11013015016017018019020021022023024091标准安装尺寸口212-30212-40212-50212-60212-65212-70212-80212-90212-95212-100212-110212-120212-130规格d304050606570809095100110120130D235280315370435485D1200225280335395445D2788798110115120130140145L150162172182D36072809095100110120125130140150162D4I1\88101106116121131141151156166171178n-①8-①1812-①1812-①23H200220205.206.207型机械密封主要尺寸d3035404550556065707580859095100105110115120125130140150160170180190278标185205235260290315370405435485D20523526031537043548554091标20621524528033540546052020723027030036042548555578标160170200225225280320355395445D120520022528033539544549591标20618021024029535541047020719022025031037043049078标116135164188220245270312353403D220516418824529835340346291标20614917520325931236342120714917520325931236342178标4-0144-①188-①1812-01812-02312-02n-①2058-①1812-①1812-02316-0291标2068-①188-02312-02312-02516-022078-①238-①2512-02512-03016-①3016-032053043103153203303583673703824004104H20631632232733234237037938239441242042073283343393443543823913944064244304205t-207t53606570GW205275287295300310330330340345350355360365370380390400L205CT337360360365385400405420425435435440445450460470480L206CT360380385390410430430匚465470480480490495500510520530L207CT36038038539041043043046547048048049049550051052053044,55221.222型釜径向双端面机械密封221.222型安装尺寸d304050606570809095100110110120130140221D185220250285340395D1145180210240295350D2109149175203259335R1315151717R14556H110119137146n-①4-①188-①188-02212-①22222D215245280335405460D1180210240295355410D287109120149175203230259R13.9141517R145H111116118136138150153n-①8-①188-①2312-①2312-①25255型双端面机械密封d30-4045-6065-8085-100105-125D1190210230260290D2170190210230260n-①4-①124-0144-0144-①184-①18H150152152160160h38414145452010型安装尺寸dDD1D2n-①「L2

30170145706-①1422540200170806-①18225502302001008-①18240602552251208-①18255702752451308-①18275802952601458-①23290903102751558-①232901003152801708-①233101103353001808-①233201203453101908-①233302012型安装尺寸dDD1D2n-①HH130235200806-①1837095402602251008-①1837595502602251008-①1838095602802451208-①1840095703002601458-02340595803302901758-02341095903302901758-023410951001103302901758-023410953703201808-026420951203903401908-026420952001-2005型安装尺寸d30-4045-5560-7075-8590-100110-130140-160D175240240275305330395D1145210210240270295350D2110176176204234260313DW85140140180200220270n-①4-①188-①188-①188-0228-①228-①2212-①22L1L2148160160170180200205215230260280280305310C24262628303234h6666666

2006.2007型机械密封安装尺寸d30-4045-5560-7075-8590-100110-130140-160D200240255295305330395D1170210225260270295350D2130176176204234260313DW100140140180200220270n-①4-①188-①188-①188-0228-①228-①2212-①22L1160170170180180200205L2215230260280280305310C26282830323436h6202.202F.202FF.204.204F204FF型机械密封尺寸d20253035404550556065707580859095100110120125130140150160170180190200D78标16017018519520523526029031534037039040543591标235260315370435485D78标13014015016017020022525528030032035035539591标200225280335395445D78标10011011612513516418822024526028030031235391标164188245298353403D36570758595120140160180200220250280-，D420250556065707580859097102107112117122127132142152157162172182202F42.548535863687379859196102108113119124129140152157164176187201216226240250D5202414651566166717682879297102107112117122132142147152162172202F354045505661667278848995101106112117122133145150157169180194209219233243n-①78标4-①124-①188-①1812-01812-①2391标8-①18r12-①1812-023h78标22242891标24262830c78标491标4.551GW204.GW204H机械密封尺寸

d20253035404550556065707580859095100110120125130140150D130140160190210240265280D1D21001101301501702002252407080100116135164188203H130140C242628h4n-①4-0144-①188-①18填料箱轴向接触式轴封，适用于压力0.6Mp压力以下要求轴的密封，结构简单，安装维修容损易对釜内物料造成污染，对密封处轴的光洁度及饶度要求严格。

403,404型填料箱主要尺寸dD1D2D3n-①H1H重量(Kg)30,35,401751451104-①181203201850,552402101768-①181203203960,65,702402101768-①181603804375,802752402048-①221804205690,95,1003052702348-①22200450711103302952608-①2220045084120,125,1303302952608-①22240530117140,150,16039535031312-①22240530135180,20046041037012-①26240600190401,402型填料箱主要尺寸dD4D3D2h1h2H1Hn-①重量(Kg)25,301851501164231091724-①181135,40,452051701354.523.51091724-①181750,55,60,652352001644.5261362098-①181870,75,80,852602251884.5261362098-①182190,95,1002902552174.5281632478-①1833110,120,1253152802454.5281632478-①1837130,1403403052716321752608-①1841150,16039535031963217526012-①2250180,20044540037063219729012-①2261506,516,606,616型填料箱主要尺寸d30,35,4040,50,5560,65,7075,80,8590,95,100110120,125,130140,150,160130,120D1175240240275305330330395440D2145210210240270295295350395D3110176176204234260260313369IIPN0.6147156176234234234268268268HPN1.6167176202266266266308308308n-①4-①188-①188-①188-①228-①228-①228-02212-①2212-①26填料尺寸10X1010X1013X1316X1616X1616X1620X2020X2020X20h^182224303235:5重量PN0.66.816.418.223.231.43747.955.572

(kg)PN1.67.518.320.520.534.641153.86280液封主要尺寸d30,35,4045,50,5560,65,7075,80,8590,85,100110120,125,130140,150,160180,200D102114133275305330H1115114120145155155165165185h155155160180195195205205245503,603,218,1414填料箱主要尺寸公称直径DNd1DD1HH1压盖螺柱重量（kg）数量直径30508010596434M123.535559012096434M123.540609012096434M124.43457110514096554M127.1507610514096554M127.16086120150113554M127.36591120150113554M127.57096120150113554M127.875101125二155113554M128.180106140J170113554M129.590122160190135674M1612.595127170200135674M1615100132170220013567:4M1618.5110142185口215135一^674M1621.5120152185215135674M1623.4125157200230135674M1624.4130162200223013567L4M1624.414018022012501558516M1625.5150190230265155856M1629160200245280155856M1632170210245280155856M1632180220265300155856M1642200240290330155856M1646

1410,1411,1412,1413型填料箱主要尺寸dd1DD1D2D3D4Lh1h2h3h4h5HH1法兰螺栓孔压盖螺柱重量（kg）n①数量直径14101412型14111413型30508011011615018560422556735172109418184M129.99.1355585110116150185604225567351721094184M129.99.1406090120135170205604.5225567351721094184M1211.810.8456590120135170205604.5225567351721094184M1211.810.85076105140164200235654.5266769352091368184M1217.616.35581110140164200235654.5266769352091368184M1217.616.36086115145164200235654.5266769352091368184M1217.616.36591120150164100235604.5266776352091368184M1218.116.57096125155164200235604.5266776352091368184M1218.116.580।106135165188225260654.5266776402091368184M122220.485111140170188225260654.5266776402091368184M122220.490122155189217255290654.5287976402471638184M1633.531.195127160194217255290654.5287976402471638184M1633.531.1100132165199217255290654.5287976402471638184M1633.531.1105137170204217255290654.5287976402471638184M1633.531.1110142175209245280315704.5287976402471638184M163835.5120152185219245280315704.5287976402471638184M163835.5125157190224271305340704.5287976402471638184M1642.539.7130162195229271305340704.5287976402471638184M1642.539.7140178210240271305340704.5328282402931831284M164947.7150188220250313350395704.53；10085403082201286M166154160198230260313350395704.53510085403082201286M166154180220255285363395440704.5351001064031522012226M168170200240275305363395440704.5351001064031522012226M168372三叶桨旋式搅拌器(a)三窄叶整体旋桨式ZHX(b)三窄叶可拆旋桨式ZCX(c)三窄叶整体带稳定器旋桨式ZHW式ZCW式KHW(d)三窄叶可拆带稳定器旋桨(g)三宽叶整体带稳定器旋桨(e)三宽叶整体旋桨式KHX(f)三宽叶可拆旋桨式KCX(h)三宽叶可拆带稳定器旋桨式KCW本系列搅拌器类似于三叶推进式搅拌器，属轴流型搅拌器，其特点是循环能力大，而动力消耗小，同时有一定的剪切能力，因而其应用场合很广泛。主要用于低粘度的混合、溶解、悬浮、结晶、反应、传热、稀释、调和等操作过程。稳定器可据要求设计成稳定筒及稳定片两种，如采用稳定片，将型号中的W改成P,常用条件为v<10000cp,n=20-600rpm,V=2~15m/s,Dj/D=0.2~0.6,宽形B/Dj-0.4,窄形B/Dj=0.2。ZHXflOfJQZDX(KCX)ZHW(KHW)W-7picture7-7三叶旋桨式搅拌器主要尺寸表表7-8DJdd1hh1MKJS(不锈钢/碳钢)寸表S1(不锈钢/碳钢)寸表重量(KG)不锈钢/碳钢B=0.4DjB=0.2Dj15025/3045/555510M51053/4-0.76/0.730.69/0.6720025/3045/555510M51353/4-0.89/0.850.83/0.8124030/3555/606010M51603/4-1.0/0.940.91/0.8628030/3555/606010M61854/6-1.30/1.21.14/1.0832030/35/4055/60/707010M82156/8-1.47/1.331.25/1.1636030/35/4055/60/707010M82406/8-2.95/2.582.39/2.1540040/45/5075/80/858015M102658/1010/123.42/2.982.68/2.3745045/50/5580/85/909015M103008/1010/128.92/7.715.71/5.0550050/55/6085/95/10010015M103358/1010/1211.68/10.168.31/7.3456055/60/6595/100/10510520M1237010/1212/1414.88/12.989.46/8.4960060/65/70100/105/11011025M1240010/1212/1420.28/18.3112.86/11.665060/65/70100/105/11011025M1243510/1212/1423.35/20.6214.48/13.9172065/70/75105/110/12012030M1248010/1212/1426.4/23.718.5/17.880070/75/80115/120/13013030M1253512/1414/1628.9/27.822.5/22.090075/80/90120/130/15015035M1660012/1414/1636.4/24.828.1/27.4

100080/90/100130/150/16016035M1666512/1414/1645.6/44.235.3/34.5110090/100/110150/160/18018035M1673514/1616/1860.1/57.945.4/44.41200100/110/120160/180/19019040M1680014/1616/1873.1/70.254.5/53.21400110/120/130180/190/20020040M1693514/1616/1896.1/92.771.5/71.11600120/130/140190/200/21021045M16107016/1818/20130.3/125.895.07/93.081800130/140/150200/210/22022050M20120016/1818/20160.2/154.2115.2/111.22000140/150/160210/220/24024050M20-16/1818/20194.9/185.8138.3/134.32250150/160/170220/240/25025060M20-18/2020/24262.1/252.9183.6/179.32400160/170/180240/250/26026060M24-18/2020/24302.6/281.3213.5/206.72500160/170/180240/250/26026060M24-18/2020/24320.3/302.8230.2/224.42800180/200/220260/290/32032080M30-20/2424/30388.7/385.8277.8/275.73000180/200/220260/290/32032080M30-20/2424/30446.5/443.1327.6/325.23200180/200/220260/290/32032080M30-20/2424/30511.5/507.6384.4/381.5GLJSGLYSGLDS系列搅拌提升装置1、概况：GLJS、GLYSGLDS系列搅拌提升装置是引进美国技术，与相关科研院所联合研制的新型搅拌提升装置。本产品广泛用于矿山、冶金、冶炼、化工、污水处理等领域中固液相间的澄清、分离和轻相回收。2、功用和结构原理：该设备由三部分组成(1)提升装置：在固相堆积过多，承载超负荷情况下使耙机提升一定高度，不会导致停机，以及检修维护时将耙机提升适当高度，方便操作；通过蜗轮、蜗杆、丝杆传动实现提升要求，提升的控制可以用手动，也可以用自动控制；提升高度范围：0800mm提升速度根据要求进行设计。(2)传动装置：该传动装置是根据大扭矩、低转速的使用要求进行设计的，根据物料情况及工艺要求，最高功率达11KW最低转数达0.01转/分钟；传动装置中有报警装置，当设备超载时，通过报警进行适当提升；传动减速系统可用二级、三级或四级实现。也可由多点行星传动，非常适合在特大型、大锥角的沉淀槽使用，具有传递扭矩大运行平稳、噪音低、可靠性高等特点。(3)耙机：主要作用是进行刮料，将固相物料分离；耙机有两桨式和四桨式，耙机叶片安装时有一定倾角，方便刮料，并能减轻阻力，降低功耗；在多级澄清槽中，耙机可以多层安装3、图示分别为GLJSGLYSGLDSB拌提升示意图，如需咨询或订货请与我公司联系，我司会根据贵方所提供的工艺技术条件及要求作出相关设计。3、概述是高效沉降槽的专用装置，比原沉降槽提高效率几倍到十几倍。GLDS^多点传动装置，实现了低速大扭矩连续运转的要求,GLDS®澄清槽外形尺寸GLDS©澄清槽基本参数规格搅拌功率KW输出转速rpm搅拌许用转矢巨重量kgGLDS73X3=90.1620000019578GLDS104X3=120.1625000028550GLDS144X5.5=220.1630000038938GLDS164X5.5=220.1240000039808规格Ddd1H0HLWW1GLDS770005508961355019083322000288CGLDS10100005508961415019083322000288CGLDS1414000760102015065232(45023103267GLDS1616000760102016993243550024123308,GUSSGLYS6~15B清槽基本参数规格搅拌许用功率KW输出转速rpm提升功率提升速度提升行程搅拌许用转矩重量kgGLYS61.5~30.25-0.500.7554300310004520GLYS82.2〜40.20-0.500.7543300340005010GLYS1(3~5.50.10-0.251.132350469005980GLYS1：3~7.50.14-0.352.232400548006210GLYS14〜7.50.08-7.52.242400660007340GLYS6~15B清槽外型尺寸GLJS6~15澄清槽基本参数规格搅拌功率KW输出转速提升功率提升速度提升行程搅拌许用转矩重量kgGLJS61.5~30.24~0.480.75543001200C1882GLJS82.2~40.2~0.50.75433002000C3325GLJS10)3~5.50.15~0.481.1323503050c5890GLJS12!3~7.50.14~0.352.2324004150c6355GLJS15i4~7.50.10~0.202.2424005200c6535DBHH0d1MXNdXcL1EXEGLJS6600040210042004401400X1400245X1610001600X1600GLJS8800040210053004401400X1400245X810001600X1600GLJS101000040232058004701600X1600273X2011051912X1912GLJS131300040232062004701600X1600273X2222751912X1912GLJS151300040240065005001800X1800299X2422752000X2000规格外型尺寸GLJS6〜15型澄清槽外形尺寸规格外型尺寸DHH0hH1CMXNL1AB1B2FEn-sdh6d112GLJS760001880420030016040900X9008005648506531503704-小151203001020GLJS8800017955300400300401200X1200319590810658673102X2406-小171503403445GLJS1C1000025735800560300401300X13001795120312609823102X2406-小171653402045GLJS131200025736200560300401300X13001795142212609823102X2406-小171803802138GLJS151500025736500560220401300X13001795142212609823102X2404-小222004202138釜用机械密封釜用机械密封标记说明:釜用机械密封标记说明:使用压力（MPh）轴短（或箱套外楂）密封网材科代号（见费4-2）箕他材料代号（见集4-3）•环材料代号《见衰4-小动环材料代号《如表4-1》机械密氧型号

材料代号适用范围氧化铝陶瓷L除氢氟酸、高浓热碱外的腐蚀性介质金属陶瓷J油、污水、弱酸、醇等介质硬质合金Dg油、污水、弱酸、弱碱、烧、醇等介质t0200c碳化率乌W油、污水、酸、弱碱、颗粒性介质t<200C碳化硅O各种介质氮化硅Dn除氢氟酸、浓碱外的所有介质浸渍酚醛石墨Mg酸（除硝酸化等族氧化性酸外）t0170c热压酚醛石墨Mr浸渍吠喃石墨Mk酸（除强氧化性外）碱t<200C浸渍环氧石墨Mh弱酸、碱t<180C浸渍铜石墨Mt油、热水、海水、有机溶剂、醋酸、乙脂等填充聚四氟乙烯Ft各种腐蚀性介质t0120C锡青铜Te油、盐、醇、脂肪酸、海水等硅锥Gt硫酸耐磨铸锥Nt醇、油脂肪酸等整体不锈钢Zb按不锈钢耐蚀性而定釜用机械密封动环、静环材料代号及选用表表3-8密封圈材料代号其他材料代号材料形状代号适用范围丁睛橡胶O1O材料代号适用范围硅橡胶O2-60~+200C醇、碱等碳钢T无腐蚀性一般介质cQ-40~+120c溶剂及各种腐蚀介弗W豕月乂O3生1Cr18Ni9TiS1一般酸、碱等氯丁橡胶O4-40~120c无机酸、碱、水、倬聚四氟乙烯O5-180~+250C各种腐蚀性介方t0Cr18Ni12Mo2TiS2尿素、酸、碱等聚四氟乙烯V6-180~+250C各种腐蚀性介质框、锚式KSMSS搅拌器

框式；锚式搅拌器DJdHd1h1h2lerqf许用扭矩N.Ma&bcd2重量(kg)47030370M8117165-39025114.636636I160M3757040450M10142200-310035362.94064c190MB1066050520M12165240-512035658.95501050220M102076050600M12190275-512035840.45501050220M102585065680M16212310-7140401057631263250M123595065760M16237350-7140401528631263250M1240114070910M16285420-7140402031701270250M12531340801070M163354506707170603510901435320M12751530901220M203825107707200804488.51001445390M129417301001380M204325808707200806420.51201650400M1628019201101530M20480640960923010076401301850470M1632021201201690M245307101060923010099321501860470M1639023201401850M2458078011609250100120851602060490M1648025201502010M2463084012609260100136251802260500M1667026201602070M24655850131011270120156001902270560M2073027201802130M24680880136011280120175082002470570M2089029202002290M24730930146011300130197002102470590M20960特殊框式与锚式搅拌器DJdd2hHB&d1L重量(kg)MKSMDSFKSFSSBKS500508585500508M83011.2416.8115.2914.2526.6560559090一550568M83013.5219.918.3116.0832.7630601001006306310M104020.3628.827.4325.7946.9710651051057107110M104025.0537.0733.6229.6657.3800701101108008012M105033.8848.5544.7837.3978.9900901501209009012M105043.56457.6245.07109.5100090150130100010012M126054.4279.9972.3660.01127.7112010016014L011：2011214M126076.55107.410170.961741250100160150125012514M127095.39137.1125.9106.72161400110180160140014014M1270117168.4154120.92671600120190180160016016M1680173.7237.9228.4166.539818001302001910180018016：M1680213.6296.9279.7187.54772000130200200200020016M1690257.9354.1366.6225.85752240140210210224022018M1690450.8481.4252.4280.37722500150220220250025018M20100423.5579.8547346.79422800160240240280027018：M20100537.8746.4696412.411913150180260250315030020M20120726.5983.7934.1525.516103550200280260355033020M20120904.112671158661.11950机架―J-AJ-B机架(HG5-746-78附件2)1.J-A和J-B型机架与LC、DC型立式减速机配套使用。.J-A型适用于立式减速机的I型轴头，配JQ型夹壳联轴器(HG5-213-65),要注意本机架不适用于搅拌轴轴向力较大使用的场合。.标号示例：J-A-30,即为减速机出轴径为30的不带支承的J-A型机架。.J-B型：适用于立式减速机的II型出轴，配用TK型或GT型联轴器，有中间支承，用中间轴承来承受搅拌轴上的轴向力，因此适用于搅拌轴有较大轴向力作用或搅拌轴较长而且反应罐中不设支承的场合，当采用Tk联轴器将减速机出轴与搅拌轴相连时，搅拌轴必须有二个独立的支承点。.标号示例：J-B-50即为减速机出轴轴径为50,带中间支承的J-B型机架。6、型号意义:甲甲母T■席速机出轴直径型为无支承机器，B型为帝支电机串।■机罂英型代号闻2TJ7型翻身J-A型机架主要尺寸及联接尺寸标定型号减速机轴径d尺寸重量kgD1D2D3h8D4D5D6h8HH1b1b2f1f2n1d4n2d3SJ-A-3030k6260230200315285240340199161646614614826J-A-4040k62902602303553202603902131618466146181035J-A-5050k63403052703953602904602391820568188181045J-A-5555m63403052704354003254603282222568188181260J-A-6565m64003603204354003255402692222568188181265J-A-7070m640036032048545037062035022246881812181265J-A-8080m646041036048545037062032022246881812181278J-A-9595m6520470420550510420700344242868122312231298J-A-1001()0m65705204756055654608004442430681223122314150J-A-11010m65705204756055654608003802430881223122314150J-A-1301，0m6880800680880810720940490283610121233123318246J-B型机架主要尺寸型号减速机轴径dD1D2D3DMH轴IH0璃H1尺H2寸b1t1b2t2HH0H2H31外■14形E1及5E2美装D0尺D1寸D2D3J-B-30J-B-30J30k6，.037.53535M40X1.555272114826636435500661311242272471832033350106260230200J-B-40J-B-40J40k65i0474545M50X1.5752.3725161235846485600801351642433031522023358130290260230J-B50J-B50J50k6()0576555M60X2962.3729201444.5856565640851152062022472022473783150340305270J-B55J-B55J55m675726565M75X2962.89352016491)70660640951262063633122952443975185340305270J-B-6565m6757270M75X21262.8:352018581)70660952673022343975185400360320316

J-B-65J659700125312244J-B-70J-B-70J70m69086.58085M90X21262.81138242062.51285700745971252673403572622793980185400360320316J-B-80J-B-80J80m69086.58085M90X21552.811382422711285730805951153263123672342893980185460410360J-B-95J-B-95J95m6110106100105M110X21853.311382425861410584089010712738634937925828843101230520470420J-B100J-B100J100m6130126115120M130X21853.313382628901412594011116138644539523828843117260570580520475470J-B-110J-B-110J110m6130126115120M130X22143.3133826281101412594011110144638539527828848117260570580520475470J-B-130J130m6150145140M150X221444130321191614211001604464403487392320880800680★为便于搅拌轴、机架、安装底盖、凸缘法兰的选型设计，请参阅本说明书搅拌装置栏n1-diB-B注：加注“J”为本公司企业标准系列产品

★为便于搅拌轴、机架、安装底盖、凸缘法兰的选型设计，请参阅本说明书搅拌装置栏n1-diB-B机架―JXLD型摆线针轮减速机机架dJ-D506机架―JXLD型摆线针轮减速机机架dJ-D506JXLD型摆线针轮减速机机架■■机・餐■・机・修机分XLD・1、本机架专供BLDXLD型摆线针轮减速机联接。■■机・餐■・机・修机分XLD・2、JXLD3-JXLD6型上端连接为右半型式，JXLD7-JXLD11型，上端连接为左半型式n1-M1均为螺孔。3、I型为普通型，口型为增高型。JXLD减速机轴径d搅拌轴轴径dJBLD型搅拌轴轴头尺寸机架型号机型轴径Dd1d2d5d3k61234JXLD335K6JBLD140K640M45X1.542.84560213103JXLD445K6JBLD250K650M55X2525575249144JXLD555m6JBLD365K660M65X2626575298144JXLD665m6JBLD480m670M75X2727590273164JXLD780m6--85M90X28790105312204JXLD890m6JBLD565m695M100X297100125320204JXLD9100m6JBLD695m6105M110X2107110125308204JXLD10110m6JBLD7110m6115M120X2117120155262244JXLD11130m6JBLD8130m6135M140X2137140155259284JXLD型机架外形尺寸及安装尺寸表2-10

JXLD减速机轴径d搅拌轴轴径d外形连接尺寸I型II型机架型号H1H2H4D1D2D3n1-M1D6D5D4H8f2b2n2-<j)HH3重量HH3重量JXLD335K6293140402302001706-M104103603006186-185201695561025960JXLD445K6343169452602302006-M104504003356186-185701568067025686JXLD555m6392169503403102706-M105004503856228-18650174110750274120JXLD665m6388205504003603168-M1253048041082212-18660174130760274140JXLD780m6438231604303903458-M1656551043082412-22740189150360309178JXLD890m64902956049545040012-M1656551043082812-22800192208920312230JXLD9100m64883056558052045512-M20580520455103012-22810195235920305262JXLD10110m64833767065059052012-M20650590520123012-22830218300950338345JXLD11130m64803767088080068012-M30880800680123012-378502304801970350538机架一搅拌机架（CD130B-86SJ型机架外形尺寸及联接尺寸机架代号HH0H1H2H3H4H5H6H7hh1h2h3h4h5h6输入端接口D1D2D3n1-mSJ55A/B10704504023C0462!06246/5696118152830012050270310/3053406-M10/8-M16SJ65A/B1140450487300512!6624661261431832275135563163604008-M12SJ70A/B1140450487300512!66246/56126143183227513556316/320(316)3604008-M12/8-M16SJ80A/B1230450545350563i26286/58155163183225014770345/360390/410/130/4608-M16/8-M20SJ90A/B1400500569350563i56287817016820363801628040045049012-M16SJ100A/B1510600685350613i86289/510185178244236018290455(460)/47052058012-M20SJ110A/B15106006853506144628111021417824423801829052059065012-M20SJ130A/B161060076135066446301110214208284637020011068080088012-M30

机架代号标准图号输出端接口d0d1d2M1d3hgd4Rb1b2t1t2机架重D4D5D6n2-<j)量kgSJ55A/B130B8.132540043512-小14555757M60X260651885656?0-0.2168SJ65A/B130B8.235042046012-小18657172M75X27580110106970?0-0.2257SJ70A/B130B8.335042046012-小18707172M75X27580110106970?0-0.2257SJ80A/B130B8.438045549512-小18808182M85X285901.510107980?0-0.2368SJ90A/B130B8.543051055512-小23909192M95X2951101.512128990?0-0.2421SJ100A/B130B8.648056060516-小23100110112M115X211512521414109109.5?0-0.2510SJ110A/B130B8.756065070016-小27110111112M115X211512521414109109.5?0-0.2613SJ130A/B130B8.872081088020-小27130135137M140X1214015021414132134.5?0-0.2987★为便于搅拌轴、机架、安装底盖、凸缘法兰的选型设计，请参阅本说明书P96页搅拌装置栏3f号事左意义及承例二3f号事左意义及承例二«：机架―XDXS型机架(HG2156621567-95)i、概述本系列机架是化工行业最新标准机架，是为搅拌传动装置（HG21563-94）配套的机架。XD型为单支点机架，减速机出轴用DF型联轴器与搅拌轴联接，XS型为双支点机架，减速机出轴用TK型联轴器联接，两支点间用DF型联轴器联接。机架分A型（轴封采用2001、2003、2004、2006或2008型机械密封）和B型（轴封采用2002、2005、2007型机械密封或506、516、606、616型填料箱。2、型号意义：♦通机类型（见囊£-11）X・机■出轴的贝11机架型式（A3L豳）作动”轴径/见疑2-10研事型号便衰2-12）XDXS型机架输入端接口尺寸表2-11减速机输出轴径d0减速机类另代号D1D2D3n1-M1f1D8D912Z651001204-M6314Z851201404-M8318Z1001341604-M8433036025Z1301601806-M84C1702002306M10330C2001302606-M12435Z1702002306-M105C2302602906-M12440Z1702002306-M105C2302602906-M12442545845Z2002302606-M105C2302602906-M12450Z2002302606-M105C2703053408-M16555Z2703103408-M105C2703053408-M16549553060C3203604008-M165Z3163604008-M12665Z12703103406-M105C3203604008-M16570ZC316320(316)3603604004008-M168-M1665600645Z3453904308-M16680M126C3604104608-M20690Z40045049012-M168C3604104608-M20695Z40045049012-M168700745C45552058012-M2010100Z45552058012-M2010C47052058012-M206110Z52059065012-M2012C47052058012-M206120Z52059065012-M2012C55060066012-M206130ZC68068080080088088012-M3012-M30128800880140Z68080088012-M3012XRXS型机架参数及尺寸表机架型号机架公称直径转动轴轴径d转动轴上端轴径d1减速机输出轴径输入端接口输出端接口外形及其他尺寸轴承型号重量kgD4H9D5D6112-df2A型B型H3H4上部XS型式下部A型B型HH1H2H5LHH1H2H5LXD1200302012见245:!953408-226i575220406--730295481--1718-462084447

1418表2-940302530410485462104448XD22505040303540290:，5039512-226750268548--995380668--2022-46212839360453540455566764621585957055455055563683462178797XS3/XD33006045354045320，L0044512-2261155/795279204/5916203391400/1040339324/7117454292032/2213512462191511/121162/1327055455055197/598383317/7185081351446221154/123165/1368065556065186/609413306/7295381351646224158/126169/137XS4/XD440090节657080415，51556516-2661310/890310206/6796954511535/111542C316/7898105662534/261351846224250/200264/21410085657080195/690471305/8005861352c46226260/208274/222XS5/XD550010085708090520(>2057020-2661620/1075255/8104711870/1325494380/9359905863036/301352c46228425/326451/352110909095100251/814501376/9396461352346230429/329455/3551201009095100j6J247/818865521372/9436661352546228437/335463/36113011095100110234/831569359/9566941352846230455/341471/367XS6/XD67001201009095100670,,8083028-26618