项目管理图片说明书.ppt

1、1,V408 -Back Cover (44zp483) Tool pre-buy off report on 20120228,Feb 28,2012 Create by: Carlos Yu,2,Tool,Add the bottom clamp plate,3,Tool,Add the top clamp plate,4,Tool,Hoist ring holes, request make the new one,closed,The injection gate dont overtop the parts surface now,The marks on the part,The

2、marks on the part,Already made the new one_ Hoist ring holes,Already made the new one_ Hoist ring holes,10,Tool,Eject system at the cavity side,11,Tool,The cavity side,12,Tool,LKM components, waiting for Alba feedback,closed,The DME original inter locker,The DME original inter locker,15,Tool,Already

3、 opened the venting for the cavity side,16,Tool,Screw sharp edge, please eliminate all the sharp edge on the tool,closed,Already eliminated all the sharp edge on the tool,18,Tool,Cavity side, request to add one more plate, and change the insulate plate,19,Tool,Hot runner connect system, not complete

4、 yet,20,Tool,Eject system at the cavity side, used the guide pins,21,Tool,Cavity angle lifter,22,Tool,No marriage marks at the cavity angle lifter, please make the marriage marks , If possible , please make the spare parts, its too thin and its easy to break, waiting for Alba feedback.,closed,23,Too

5、l,A plate,24,Tool,The cooling system is not good, have many steel waste inside the cooling system, how the cooling can work well, please clean it before the next try out,closed,25,Tool,O-ring steel is too thin, waiting for Alba feedback, how to correct it.,26,Tool,The hardness for the cavity insert

6、1, 51.5 HRC,27,Tool,The hardness for the cavity insert 2, 51.6 HRC,28,Tool,The hardness for the cavity insert 2, 51.5 HRC,29,Tool,The cavity side,30,Tool,No marriage marks for the ware plates,closed,31,Tool,The back surface of the Cav insert 1.,32,Tool,Cavity insert 1 cooling system, have the steel

7、waste inside, please clean it for all the tools,closed,33,Tool,All the inserts have the marriage marks for the cavity side,34,Tool,Cavity insert 2, front surface,35,Tool,Cavity insert 2, back surface,36,Tool,The cooling line should be change, dont put at the end of the holes, please use the other wa

8、y for the baffle.,closed,37,Tool,Hot tip, no damage, no raw material leakage.,38,Tool,A plate,39,Tool,Some ware plate have the marriage marks. Please make sure all the ware plate have the marriage marks.,40,Tool,Insulate plate, need to be change , once add the top clamp plate,41,Tool,Hot runner syst

9、em,42,Tool,No found the water channel for the hot runner system, please make it at the tool bottom side,closed,43,Tool,Hot runner connect way, not complete yet,44,Tool,Core side,45,Tool,Have the cover for eject plate,46,Tool,Tool disassembly,47,Tool,Eject return plate,48,Tool,B plate, back surface,4

10、9,Tool,Core side, P/L side,50,Tool,B plate,51,Tool,O ring steel is too thin, Dont make the round at the corner, waiting for Alba feedback.,closed,All the o-ring grooves have be examined. And This tools o-ring grooves dont be broken. And the steel isnt too thin. Well modify the several in it. And tak

11、e the photoes afterwards.,53,Tool,Dont use the DME or Hasco original side locker for this tool,closed,54,Tool,Core insert 1, no welding mark,55,Tool,Need to check the cooling line, have water leakage at the plug region,closed,56,Tool,Core insert 1, the back surface,57,Tool,The marriage marks is wron

12、g, please correct it,58,Tool,Core insert , its too tight, waiting for Alba to confirm.,closed,59,Tool,Core insert 2, no welding mark,60,Tool,Core insert 2, back surface,61,Tool,The eject system,62,Tool,Eject stopper are found,63,Tool,Eject plate pry bar,64,Tool,Eject system, used the self- lubricate guide bush,65,Tool,The back surface of the eject plate,66,Tool,All the eject pins have the marriage marks,67,Tool,Except 2 ejec