VDX 6740 基础配置文档.docx

博科VDX交换机快速配置手册一、登录交换机1.1 串口线连接Windows平台：传输速率：9600bit/sec数据位 ：8校验位 ：None停止位 ：1流控制 ：None1.2 登录交换机 用户级别VDX Switch enable -只能使用？、ping 和 show命令VDX Switch # -查看交换机详细信息 全局配置模式VDX Switch # configure terminal VDX Switch (config) # -配置模式二、升级交换机固件1、给交换机配一个管理地址：VDX Switch # conf tVDX Switch # interface Management 1/0VDX Switch # ip address 6/242、使用FTP服务器升级固件VDX switch# firmware download interactivefirmware download interactiveServer name or IP address: 5File name: /users/home40/Builds/NOS_v5.0.0Protocol (ftp, scp, sftp): ftpUser: fvtPassword: *Do manual download y/n: nSystem sanity check passed.Do you want to continue? y/n: y使用USB升级固件VDX Switch # usb on VDX Switch # usb dirVDX Switch # firmware download usb directory nos6.0.0 coldboot Performing system sanity check.This command will cause a cold/disruptive reboot and will require that existing telnet, secure telnet or SSH sessions be restarted.Do you want to continue? y/n:yChecking conditions for downloading to 6.0.0System settings check passed (0).检查升级后的版本VDX Switch # show version 三、调整时区+设置本地时间VDX Switch # clock timezone Asia/Shanghai (修改时区)VDX Switch # clock set 2015-05-21T16:10:00（设置本地时间）VDX Switch # show clock rbridge-id 1: 2015-05-21 15:56:10 Asia/Shanghai四、设置timeoutVDX Switch (config)# line vty exec-timeout 5 （设置超时时间为5分钟）VDX Switch (config-line-vty)# do show running-config line vty line vtyexec-timeout 5!五、添加/移除license添加license：VDX Switch # license add licStr “*B H*#“ （添加license）移除license：VDX Switch # license remove licStr “FCOE_BASE“ （移除license）六、设置登录密码VDX Switch(config)# username admin role admin password password enable true七、修改设备名称VDX Switch # conf tVDX Switch (config)# switch-attributes 1 host-name VDX6740 chassis-name VDX6740八、关闭telnet：Switch（config）# telnet server shutdown 在VCS模式中关闭telnet：Switch（config）#rbridge-id 3Switch (config-rbridge-id-3)# telnet server shutdown启用telnet：Switch （config）# no telnet server shutdown九、组建VCS逻辑机箱同一个VCS 中每台VDX具有不同的RB-id和相同的VCSID： VDX Switch # vcs rbridge-id 1 vcsid 12 logical-chassis enable VDX Switch # show fabric islports all十、修改principle switchVDX switch# configureVDX switch(config)# rbridge-id 5VDX switch(config-rbridge-id-5)# logical-chassis principal-priority 1VDX switch(config-rbridge-id-5)# end VDX switch# logical-chassis principal-switchover十一、创建VLAN VDX Switch (config)# interface vlan 10 VDX Switch (config)# interface TenGigabitEthernet 1/0/1-4 VDX Switch (conf-if-te-1/0/1-4)# switchport VDX Switch (conf-if-te-1/0/1-4)# switchport mode access VDX Switch（conf-if-te-1/0/1-4)# switchport access vlan 10十二、给VLAN配置IP地址VDX Switch (config)# rb 1VDX Switch (config-rbridge-id-1)# interface ve 10VDX Switch (config-rbridge-Ve-30)# ip address 9/24VDX Switch (config-rbridge-Ve-30)# no shutdown 十三、配置生成树协议（STP/RSTP）VDX Switch (config)# protocol spanning-tree stp/rstpVDX Switch (config-stp)# bridge-priority 4096十四、配置多生成树(MSTP)VDX Switch (config)# protocol spanning-tree mstp VDX Switch (config-mstp)# instance 10 vlan 10-19 VDX Switch (config-mstp)# instance 20 vlan 20-29VDX Switch (config-mstp)# instance 10 priority 4096VDX Switch (config)# interface TenGigabitEthernet 1/0/1-4 VDX Switch (conf-if-te-1/0/1-4)# switchport mode trunk VDX Switch (conf-if-te-1/0/1-4)# switchport trunk allowed vlan allVDX Switch (conf-if-te-1/0/1-4)# int te 2/0/1-4VDX Switch (conf-if-te-2/0/1-4)# switchport mode trunkVDX Switch (conf-if-te-2/0/1-4)# switchport trunk allowed vlan all 十五、配置vLAGVDX Switch (config)# interface Port-channel 10 VDX Switch (config-Port-channel-10)# vlag ignore-split VDX Switch (config-Port-channel-10)# switchport VDX Switch (config-Port-channel-10)# switchport mode trunkVDX Switch (config-Port-channel-10)# switchport trunk allowed vlan all VDX Switch (config-Port-channel-10)# no shutdownVDX Switch_1 (config)# int te 1/0/1VDX Switch (conf-if-te-1/0/1)# channel-group 10 mode active type standardVDX Switch_2 (conf-if-te-1/0/1)# int te 2/0/1VDX Switch （conf-if-te-2/0/1)# channel-group 10 mode active type standard 十六、配置静态路由静态路由不是全局参数，需要进入到每台设备上配置：VDX SWITCH (config)# rb 1VDX SWITCH (config-rbridge-id-1)# ip route x.x.x.x/x x.x.x.xVDX SWITCH (config)# rb 2VDX SWITCH (config-rbridge-id-2)# ip route x.x.x.x/x x.x.x.x十七、配置OSPF OSPF不是全局参数，需要进入到每台设备上配置：VDX SWITCH (conf)# rb 1 VDX SWITCH (config-rbridge-id-1)# router ospf VDX SWITCH (config-router-ospf-vrf-default-vrf)# area 0 VDX SWITCH (config-rbridge-id-1)# int ve 30VDX SWITCH (config-rbridge-Ve-30)# ip ospf area 0VDX SWITCH (config)# rb 2VDX SWITCH (config-rbridge-id-2)# router ospf VDX SWITCH (config-router-ospf-vrf-default-vrf)# area 0VDX SWITCH (config-router-ospf-vrf-default-vrf)# int ve 30VDX SWITCH (config-rbridge-Ve-30)# ip ospf area 0十八、配置VRRP/VRRP-ERB1:VDX SWITCH (config)#rbridge 1VDX SWITCH (config)#protocol vrrp-extendedVDX SWITCH (config)#interface ve 30VDX SWITCH (config)#vrrp-extended-group 30VDX SWITCH (config)#priority 125VDX SWITCH (config)#advertise-backup enable VDX SWITCH (config)#preempt-mode enable VDX SWITCH (config)# short-path-forwarding revert-priority 90VDX SWITCH (config)#vritual-ip 00VDX SWITCH (config)#track ten 1/0/6 priority 20VDX SWITCH (config)#enable RB2:VDX SWITCH (config)#rbridge 2VDX SWITCH (config)#protocol vrrp-extendedVDX SWITCH (config)#interface ve 30VDX SWITCH (config)#vrrp-extended-group 30VDX SWITCH (config)#priority 120VDX SWITCH (config)#advertise-backup enable VDX SWITCH (config)#preempt-mode enable VDX SWITCH (config)# short-path-forwarding revert-priority 90VDX SWITCH (config)#vritual-ip 00VDX SWITCH (config)#track ten 2/0/6 priority 10VDX SWITCH (config)#enable 十九、配置FlexportVDX SWITCH (config)#hardwareVDX SWITCH (config-hardware)#flexport2/0/45VDX SWITCH (config-flexport-2/0/45)#flexport2/0/46VDX SWITCH (config-flexport-2/0/46)#flexport2/0/47VDX SWITCH (config-flexport-2/0/47)#flexport2/0/48VDX SWITCH (config-hardware)#flexport2/0/45VDX SWITCH (config-flexport-2/0/45)#typefibre-channelVDX SWITCH (config-flexport-2/0/45)#flexport2/0/46VDX SWITCH (config-flexport-2/0/46)#typefibre-channelVDX SWITCH (config-flexport-2/0/46)#flexport2/0/47VDX SWITCH (config-flexport-2/0/47)#typefibre-channelVDX SWITCH (config-flexport-2/0/47)#flexport2/0/48VDX SWITCH (config-flexport-2/0/48)#typefibre-channel二十、QSFP breakout 配置VDX SWITCH (config)#interface fortygigabitethernet 1/0/49VDX SWITCH (conf-if-fo-1/0/49)# shutdownVDX SWITCH (conf-if-fo-1/0/49)#exitVDX SWITC