已阅读5页,还剩2页未读, 继续免费阅读
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1,特性分级 Classification of Characteristics,分级的定义Definition of Classes 下列特性分级是根据产品关键程度:QSP1.04图1A进行特性分级.在该定义中的缺陷项目是指偏离QSP1.04图1B中规定的尺寸规范. The following characteristic class are based upon the Product Criticality Classification ,Figure 1A, QSP1.04, Classification of Characteristics. The term defective in these definitions refers to excursions from specification of a magnitude defined in Figure 1B,QSP1.04.,2,特性分级 Classification of Characteristics,关键 -关键特性如果有缺陷 将可能引起操作人员、使用者或旁人的人 身伤害。 符号图 肯定会引起操作运行故障。 Drawing 肯定会引起性能下降超过20%或不能满足 Symbol 法规要求。 Critical -Those characteristics which if defective Will possibly cause injure to an operator ,user or bystander. Will certainly cause an operating failure Will certainly cause a performance loss in excess of 20% or failure to meet regulatory requirements of EPA,CARB,ABS, UL,FM ,etc.,3,特性分级 Classification of Characteristics,重要 -重要特性如果有缺陷 有很高的可能性会引起运行故障。 有很高的可能性会引起性能下降超过20%或不满足法规要求。 肯定或很可能引起超额的修理费用包括停机、劳务、备件等。 肯定或很可能会由于机器失效引起产品完全报废,明显减少 工具的使用寿命或产生过多的废品。 Major -Those characteristics which if defective Will with high probability. Cause an operating failure. Will with high probability. Cause a performance loss in excess of 20% or failure to meet regulatory requirements of EPS, CARB, ABS, UL,FM,etc. Will certainly or with high probability, cause excessive total cost of repair including downtime.labor. Replacement part .etc. Will certainly or with high probability , cause a disruption of production by causing a machine malfunction, significantly reduced tool life or excessive scrape.,4,特性分级 Classification of Characteristics,一般 -一般特性不包含在QSP1.04的产品关键程度分级中,但如 果有缺陷根据经验和判断表明: 无符号 将肯定会降低产品外观质量,给客户提供劣质品。 将肯定会引起额外的工艺调整、清理、返修等。 肯定会在产品确认和成品控制时产生困难。 Minor -Those characteristics not included in Product Criticality Classification of QSP1.04. But which judgment and experience indicate if defective. Will certainly detract from the appearance of the product indicating inferior value to the customer. Will certainly result in extra process adjustments, cleaning,salvage etc. Will certainly cause difficulty in identification and control of the end product.,5,特性分级 Classification of Characteristics,关键控制特性 不管特性级别如何,在生产可接受的零件或 产品时,关键控制特性是很重要的,关键控 制特性在于特殊的预防控制。 Key Control Characteristic Characteristics which are most important in producing an acceptable part or product. Regardless of classification . Focus on special prevention oriented controls.,6,PPAP 检查单 PPAP Check List,零件号和更改级别 Part No.&Revision 在图纸上给尺寸编号 Giving numbers to all dimension on drawings 在尺寸检查表中注明未注尺寸公差值 Confirm tolerance of dimensions which no tolerance on drawing 专用工装、模具清单 Special tooling and mould list 量检具清单 Gauge list FMEA纠正措施的跟踪 Follow up the corrective actions of FMEA 工程更改必须经DCEC产品部门批准 Engineering changes must be approved by DCEC PE department,7,PPAP 检查单 PPAP Check List,尺寸、材料、性能测试项目必须经DCEC预先审核 Dimension/material/performance items should be approved by DCEC 过程能力和统计过程数据Process capability and statistical package 分供方清单Parts list for subcontractors 过程能力小于1.33,进行工序质量改进,并有书面改进措施计划 Cpk is less than 1.33, improve process and documented in a corrective action plan 测试的不合格项目须经DCEC审批 N
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 班级工作计划七篇资料
- 教师个人工作总结范本八篇
- 有机磷中毒的护理策略
- 医院检验报告单
- 浮子水管倾斜仪项目计划书
- 小学语文新教师述职报告
- 人力资源信息管理工作流程
- 中学生学习方法
- 平面设计实施方案(2篇)
- 电缆、电线管敷设要求
- 理论联系实际谈一谈你对中国式现代化的中国特色的理解-参考答案
- 课件:燃油系统典型零部件的检验、修理和测试讲解
- 2024年武汉离婚协议标准模板(二篇)
- 项目组织管理架构及人员职责
- 16J914-1 公用建筑卫生间
- 先进封装技术可靠性
- GB/T 43928-2024宇航用商业现货(COTS)器件保证指南
- 标准的中央空调保养合同范文 2024
- 口腔牙体牙髓病的护理
- 2024年广东广州市荔湾区社区开展专职工作人员招聘笔试冲刺题(带答案解析)
- 超星尔雅学习通《中国近现代史纲要(首都师范大学)》2024章节测试答案
评论
0/150
提交评论