数车GM代码（NumberofcarGMcode）.docx

数车GM代码（Number of car GM code）数车GM代码(Number of car GM code) Editor and input program Edit program: 1, instruction format: G00 X_ Z_ This command moves the tool from the current position to the location specified by the command (in absolute coordinates) or to a distance (in incremental coordinates). G01 X (U) Z (W) F_ _ _ The linear interpolation moves from the current position to the command position in a straight line and at a given rate of movement. G02 (G03), X (U), _Z (W), _R_F_ G02 - clockwise (CW) G03 - reverse clock (CCW) X, Z - the end point in the coordinate system U, W - the distance between the starting and the finishing points I, K - the vector from the starting point to the center point (radius) R - arc range (maximum 180 degrees). ; G32, X (U), _Z (W), _E_; F - thread lead setting E - pitch (mm) G41 X_ Z_; G42 X_ Z_; G70 P (NS) Q (NF) The first segment of ns: machining program shape. The last segment nf: machining program shape; G71U (d) R (E) G71P (NS) Q (NF) U (U) W (W) F (f) S (s) T (T) F_ specifies the moving instructions between A and B from the program segment ns to nf. D: cutting depth (radius specified) does not specify a sign. E: retract stroke. The first segment of ns: machining program shape. The last segment nf: machining program shape. The u:X direction of finishing the distance and direction of reservation. (diameter / radius) W: Z the direction of finishing the distance and direction of reservation. G72W (d) R (E) G72P (NS) Q (NF) U (U) W (W) F (f) S (s) T (T) T, e, NS, NF, delta u, delta W, F, s and T with the same meaning G71 G73U (I) W (k) R (d) G73P (NS) Q (NF) U (U) W (W) F (f) S (s) T (T) The i:X axis retracting distance (radius specified). The direction of delta k: Z axis retracting distance (radius specified). D: segmentation times This value is the same as the repeat number of rough machining. The first segment of ns: machining program shape. The last segment nf: machining program shape. The u:X direction of finishing the distance and direction of reservation. (diameter / radius) W: Z the direction of finishing the distance and direction of reservation. G76 P (m) (R) (a) Q (Dmin) R (d) G76 X (U) Z (W) R (I) P (k) Q (d) F (f) M: finishing times (1 to 99). R: to angular volume. A: tool nose angle: Can choose 80 degrees, 60 degrees, 55 degrees, 30 degrees, 29 degrees, 0 degrees, with 2 digits specified. The minimum cutting depth dmin. I: the radius difference of the thread part. If i=0, it can be used for general linear thread cutting. K: thread height This value is specified in the X axis with a radius value. The cutting depth of d: for the first time (radius) L: thread lead (with G32) G90, X (U), _Z (W), _F_. Cone cutting cycle: G90, X (U), _Z (W), _R_, F_; Note: the R value of the cone must be specified. G92, X (U), _Z (W), _F_ Taper thread cutting cycle: G92, X (U), _Z (W), _R_F_ Bench cutting cycle: G94, X (U), _Z (W), _F_; Taper bench cutting cycle: G94, X (U), _Z (W), _R_, F_; The function of the G96 is to perform line speed control and maintain steady cutting speed only by changing the RPM to control the corresponding workpiece diameter variations. The function of RPM is to cancel the line speed control and only control the stability of G97. 2, edit program: Edit the program as shown: (Note: 40 circles are not processed) O1234 G50X100Z100 MO3 TO1O1 GOOX56Z2 G71U3R1 G71P1Q2U0.5W0.1F0.2 N1 GOOX22 G01Z0F0.04 X24Z-1 Z-25 X26 Z-30 G02X46Z-40R10 G01X48 X50Z-41 Z-79 N2 X56 GOOX100 Z100T0100 T0202 G00X25 Z-25 (Note: knife width 3) g01x20f0.1 g00x100 z100t0200 t0303 g00x24z2 g92x23z - 23.5f2.5 x22.5 x21.7 x20.9 x20.8 x20.7 x20.6 g00x100 z100t0300 m-30 法兰克数控车床g代码m代码的使用方法 m 指令代码 主轴正转 m03 m-30 程序停止 m03 s1000 主轴以每分钟1000的速度正转 m04主轴逆转 m05主轴停止 .m08 主轴切削液开 m14: m10 m11 m15主轴切削液停 the m25 托盘上升 m85工件计数器加一个 m19主轴定位 循环所以程式 m99 g 指令代码 g00快速定位 g01主轴直线切削 g02主轴顺时针圆壶切削 g03主轴逆时针圆壶切削 g04 暂停 g04 x4 主轴暂停4秒 资料预设 g10 g28原点复归 g28 u0w0; u轴和w轴复归 g41 刀尖左侧半径补偿 g42 刀尖右侧半径补偿 the 取消 g97 以转速 进给 g98 以时间进给 g73 循环 g80取消循环 g10 00 数据设置 模态 00 数据设置取消 模态 g11 g17 16 xy平面选择 模态 g18 16 zx平面选择 模态 g19 16 yz平面选择 模态 the g20 英制 模态 06 21 06 米制 模态 g22 09 行程检查开关打开 模态 g23 09 行程检查开关关闭 模态 g25 08 主轴速度波动检查打开 模态 g26 08 主轴速度波动检查关闭 模态 g27 00 参考点返回检查 非模态 g28 00 参考点返回 非模态 g31 00 跳步功能 非模态 the 刀具半径补偿取消 模态 07 g41 07 刀具半径左补偿 模态 g42 07 刀具半径右补偿 模态 g43 17 刀具半径正补偿 模态 g44 17 刀具半径负补偿 模态 g49 17 刀具长度补偿取消 模态 g52 00 局部坐标系设置 非模态 g53 00 机床坐标系设置 非模态 g54 14 第一工件坐标系设置 模态 g55 14 第二工件坐标系设置 模态 g59 14 第六工件坐标系设置 模态 g65 00 宏程序调用 模态 g66 12 宏程序调用模态 模态 g67 12 宏程序调用取消 模态 g73 01 高速深孔钻孔循环 非模态 g74 01 左旋攻螺纹循环 非模态