CCNA标准实验06——路由器.docx

CCNA标准实验06路由器的基本配置配置路由器Router0RouterenRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname ccnaccna(config)#int loopback 1 /配置环回接口loopback 1%LINK-5-CHANGED: Interface Loopback1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to upccna(config-if)#ip address 192.168.1.1 255.255.255.0ccna(config-if)#exitccna(config)#int loopback 2/配置环回接口loopback 2%LINK-5-CHANGED: Interface Loopback2, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback2, changed state to upccna(config-if)#ip address 192.168.2.1 255.255.255.0ccna(config-if)#exitccna(config)#int loopback 3/配置环回接口loopback 3%LINK-5-CHANGED: Interface Loopback3, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback3, changed state to upccna(config-if)#ip address 192.168.3.1 255.255.255.0ccna(config-if)#exitccna(config)#int s1/0ccna(config-if)#ip address 192.168.4.1 255.255.255.0ccna(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial1/0, changed state to downccna(config-if)#clock rate 64000ccna(config-if)#exitccna(config)#ccna(config)#router ripccna(config-router)#ver 2ccna(config-router)#network 192.168.1.0ccna(config-router)#network 192.168.2.0ccna(config-router)#network 192.168.3.0ccna(config-router)#network 192.168.4.0ccna(config-router)#exitccna(config)#配置路由器Router1RouterenRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname ccna2ccna2(config)#int s1/0ccna2(config-if)#ip address 192.168.4.2 255.255.255.0ccna2(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial1/0, changed state to upccna2(config-if)#exitccna2(config)#int loop%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed statccna2(config)#int loopback 1%LINK-5-CHANGED: Interface Loopback1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to upccna2(config-if)#ip address 192.168.5.1 255.255.255.0ccna2(config-if)#exitccna2(config)#router ripccna2(config-router)#ver 2ccna2(config-router)#network 192.168.4.0ccna2(config-router)#network 192.168.5.0ccna2(config-router)#exitccna2(config)#查看路由表ccna#sh ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not setC 192.168.1.0/24 is directly connected, Loopback1C 192.168.2.0/24 is directly connected, Loopback2C 192.168.3.0/24 is directly connected, Loopback3C 192.168.4.0/24 is directly connected, Serial1/0R 192.168.5.0/24 120/1 via 192.168.4.2, 00:00:07, Serial1/0ccna#ccna2#sh ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not setR 192.168.1.0/24 120/1 via 192.168.4.1, 00:00:00, Serial1/0R 192.168.2.0/24 120/1 via 192.168.4.1, 00:00:00, Serial1/0R 192.168.3.0/24 120/1 via 192.168.4.1, 00:00:00, Serial1/0C 192.168.4.0/24 is directly connected, Serial1/0C 192.168.5.0/24 is directly connected, Loopback1ccna2#问题解决：1. 再输入命令时，经常被console 口日志打断。解决：console口日志的同步启用，使用以下命令：Router（config）#line console 0Router（config）