ISO8667汽车法兰标准.pdf

BRITISH STANDARD AUTOMOBILE SERIES BS AU 214a-1:1987 ISO 8667:1986 Incorporating Amendment No. 1 Specification for Gearbox flanges Part 1: Specification for dimensions of cross-tooth gearbox flanges, type T, for commercial vehicles and buses UDC 629.114.4/.5:621.825.24 Licensed Copy: London South Bank University, London South Bank University, Wed Mar 22 03:00:25 GMT 2006, Uncontrolled Copy, (c) BSI BS AU 214a-1:1987 This British Standard, having been prepared under the direction of the Automobile Standards Committee, was published under the authority of the Board of BSI and comes into effect on 30 January 1987 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/13 Draft for comment 84/78655 DC ISBN 0 580 15687 7 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/13, upon which the following bodies were represented: Department of Transport (Highways) Freight Transport Association Institute of Road Transport Engineers (Incorporated) London Regional Transport Ministry of Defence National Bus Company Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments 5778January 1988Indicated by a sideline in the margin Licensed Copy: London South Bank University, London South Bank University, Wed Mar 22 03:00:25 GMT 2006, Uncontrolled Copy, (c) BSI BS AU 214a-1:1987 BSI 02-2000i Contents Page Committees responsibleInside front cover National forewordii 1Scope and field of application1 2References1 3Dimensions and tolerances1 4Designation1 Figure2 Table1 Publications referred toInside back cover Licensed Copy: London South Bank University, London South Bank University, Wed Mar 22 03:00:25 GMT 2006, Uncontrolled Copy, (c) BSI BS AU 214a-1:1987 ii BSI 02-2000 National foreword This British Standard has been prepared under the direction of the Automobile Standards Committee and is identical with ISO 8667:1986 “Commercial vehicles and buses Cross-tooth gearbox flanges, type T”, published by the International Organization for Standardization (ISO). Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. The comma has been used as a decimal marker. In British Standards it is current practice to use a full point on the baseline as the decimal marker. Wherever the words “International Standard” and “ISO 8667” appear, referring to this standard, they should be read as “British Standard” and “BS AU 214a-1” respectively. The Technical Committee has reviewed the provisions of ISO 1101:1983 to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. A related British Standard to ISO 1101 is BS 308 “Engineering drawing practice” Part 3:1972 “Geometrical tolerancing”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International StandardCorresponding British Standard ISO 7646:1986BS AU 214: Gearbox flanges Part 2:1987 Specification for dimensions for type A gearbox flanges for commercial vehicles and buses (Identical) ISO 7647:1986Part 3:1987 Specification for dimensions for type S gearbox flanges for commercial vehicles and buses (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Wed Mar 22 03:00:25 GMT 2006, Uncontrolled Copy, (c) BSI BS AU 214a-1:1987 BSI 02-20001 1 Scope and field of application This International Standard specifies the nominal dimensions and tolerances which affect interchangeability between cross-tooth gearbox flanges, type T, and mating parts used on commercial vehicles and buses. Dimensions and tolerances of the mating parts, other than those occurring at the interface of the two flanges, are left to the discretion of the manufacturer of that component. 2 References ISO 1101, Technical drawings Geometrical tolerancing Tolerancing of form, orientation, location and run-out Generalities, definitions, symbols, indications on drawings. ISO 7646, Commercial vehicles and buses Gearbox flanges Type A. ISO 7647, Commercial vehicles and buses Gearbox flanges Type S. 3 Dimensions and tolerances Nominal dimensions and tolerances which affect the interchangeability of type T gearbox flanges shall be as shown in the Table and Figure. Where the flange is formed by forging, an additional groove either side of the driving teeth is permissible. In this case the additional grooves do not form part of the drive. 4 Designation Gearbox flanges meeting the requirements of this International Standard shall be identified by a certain number of elements, to be given in the following order: a) reference to this International Standard; b) type T; c) size code. Example: Designation of a type T gearbox flange of size code 1: Flange ISO 8667-T1 Table NOTEGearbox flanges of types A and S, as specified in ISO 7646 and ISO 7647 respectively, are designed for force-locking (friction) torque transmission, their capacity for transmission being determined by the size of the flange and the bolts. As static or dynamic torque loads increase, however, a point is reached when these are inadequate, and there is a need for form-locking components. Increasing problems are being encountered with the flange joint in the assembly of drive shafts for heavy lorries, as power tools cannot be used because of space limitations, and because the large bolts, M16 type, have to be tightened steadily to a torque loading of about 300 Nm for example. With special vehicles it may also be necessary to replace the engine, transmission units or axles in the shortest possible time, but this can be impracticable with a conventional flange joint which has, for example, ten M16 bolts. This form-locking flange joint has been developed to avoid the need to increase the size of the flange or bolts while achieving the required performance or to simplify assembly. Initially, a flange joint with spiral bevel-type teeth was developed but this is expensive to manufacture. The flange joint specified in this International Standard overcomes the problems described above. It requires only four bolts which are smaller than comparable flanges of conventional construction, and the alignment of the drive shaft is not dependent on them. The drive shaft flange and the transmission flange centre themselves through the groups of teeth which intersect at 70 which improves alignment, and play, which occurs in conventional joints, is eliminated. As the drive is transmitted through the teeth, the axial force which arises under torque loading, which must be carried by the bolts, is relatively low. A further feature is that jamming between flanges during dismantling is prevented. The teeth can be produced on a universal milling machine with special cutters for short production runs, while for mass production the use of a surface broaching machine is envisaged. The simple tooth form can be measured easily, thus ensuring interchangeability between components made by different manufacturers. Size code d1 0,5 d2d3 0,5 d4 0 0,2 l 0 0,5 d5 + 0,2 0 d6 0,2 115013095111121315 2165140105121121315 3180150105128141517 4200165125143161517 Licensed Copy: London South Bank University, London South Bank University, Wed Mar 22 03:00:25 GMT 2006, Uncontrolled Copy, (c) BSI BS AU 214a-1:1987 2 BSI 02-2000 Figure Licensed Copy: London South Bank University, London South Bank University, Wed Mar 22 03:00:25 GMT 2006, Uncontrolled Copy, (c) BSI BS AU 214a-1:1987 BSI 02-2000 Publications referred to See national foreword. Licensed Copy: London South Bank University, London South Bank University, Wed Mar 22 03:00:25 GMT 2006, Uncontrolled Copy, (c) BSI BS AU 214a-1:1987 ISO 8667:1986 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price