免费预览已结束,剩余1页可下载查看
下载本文档
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
重介质旋流器结构参数调整与分选效果的研究张雅珊(天地科技股份有限公司唐山分公司 ,河北 唐山063012)摘要通过对重介质旋流器分选原理及结构参数的论述 ,介绍了重介质旋流器结构参数对分选效果的影响 。关键词重介质旋流器中图分类号 : td942 + 17分离锥面中间空气柱文献标识码 :a等密度线零速面下 ,密度大的矿粒很快移向器壁 ,在外螺旋力的作用下 ,由底口排出 。轻密度矿粒则进入“分离锥面”内 , 在内螺旋力作用下 ,从溢流口排出 。从而完成整个 分选过程 。“分离锥面”的形成取决于垂直零速面 ,并与径向零速面有关 。“分离锥面”周界面则取决于 旋流器的结构 。1引言重介质旋流器是重力选煤效率最高的一种设备 ,它的显著特点是体积小 ,无运动部件 ,处理量大 ,分选效率高 ,特别是对难选 、极难选原煤 ,细粒级较 多的氧化煤 ,高硫煤的分选有显著的效果和经济效 益 ,故应用比较广泛 。从表面上看 ,旋流器的外部结 构非常简单 ,本身又无运动部件 ,但其内部液流的运 动却是极其复杂的 。流体在旋流器中的运动规律与 旋流器的结构是密不可分的 ,改变旋流器的结构参 数会使分选效果发生很大变化 。因此 ,要想达到预 期的分选效果 ,旋流器的调节就成了一个关键问题 。图 1 重介质旋流器分离锥面构想图212矿浆在旋流器中的运动规律 为了弄清“分离锥面”与旋流器结构的关系 ,有必要了解矿浆在旋流器中的运动规律 。 重介质旋流器内矿浆的运动是个较为复杂的旋涡流运动 ,对其内任一点的速度可分为 : 切向速度 、径向速度和轴向速度 。切向速度是确定离心力大小 的重要因素 ,径向速度对向心曳力起重要作用 ,轴向 速度决定着被选物料是沿外螺旋下降 还是沿内螺 旋上升 ,以及位移的时间 。在一定程度上说 ,物料的分离取决于上述三种速度 ,而此三种速度则取决于入料压力 、悬浮液密 度 、悬浮液中固体质量浓度和旋流器的结构参数等 。 在此仅对旋流器的结构参数的影响进行探讨 。由于旋流器内液流的运动是绕中心轴的旋转运 动 ,用贝努力方程来描述旋流器内理想流体的位能 、动能与压力分布之间的关系 ,可写成如下方程 :2分选机理211基本原理重介质旋流器是在一个比较复杂的旋转流场中 实现产品分选的 ,有关重介质旋流器选煤基本原理的学说很多 ,但没有形成一种统一的数学方法来推导出全部运动规律的表达式 。因此 ,在研究重介质 旋流器的分选效果与影响因素的关系时 ,大都采用经验公式 。虽然有关其分选机理的学说很多 ,但比 较普通的说法是 : 在旋流器中存在一个“分离锥面”(图 1) 。在重介质旋流器内 ,带有一定压力的重悬浮液 和被选物料沿着旋流器圆柱筒体切向给入后 ,在离 心力场的作用下 ,旋流器内形成内 、外螺旋流和中间 空气柱 ,以及不同密度的等密度线 。不同密度的矿粒开始处于相应的等密度线上 。在离心力的作用2vt+pz += c2 g收稿日期 :2002 - 04 - 10作者简介 : 张 雅 珊 ( 1963 - ) , 女 , 河 北 省 唐 山 市 人 , 工 程 师 。 现就职于天地科技股份有限公司唐山分公司生产开发中心 。式中 : z 为液流层位能 ; p 为作用于该液流层的压力 ; 为液流的密度 ; vt 为测定点的切向速度 ; g 为14第 1 期张雅珊 :重介质旋流器结构参数调整与分选效果的研究2003 年 2 月 25 日综上所述 ,旋流器结构参数的变化直接影响到分离零速面的位置变化 ,而分离零速面的位置变化 ,直接影响到溢流和底流产品数量和质量的变化 ,因重力加速度 ; c 为常数 。显然 ,式中的 z + p 是液流v2t层的静压头 ,而 2g 则为液流层的动压头 。此 ,想要改变分选效果 ,就必须改变零速面 ,分离零对于旋流器内同一液流层来说 , z 为常数 ,其任一半径点 r 的压力 p 随着切向速度 vt 的增加而减 小 ,而旋流器内切向速度 vt 与半径 r 的关系式为 : vt r = 常数 。由此可知 : 由于中心区的切向速度很 大 ,产生压力降 ( 图 2) , 在旋流器轴心形成负压区 ,并由底口吸入空气 ,形成了空气柱 。速面位置的改变则可以通过改变旋流器有关的结构参数来实现 。3旋流器结构参数对分选效果的影响重介质旋流器的圆柱直径是标定旋流器规格和生产能力的主要参数 ,也是决定旋流器其它参数的 重要因素 ,因此应根据原煤的处理量 、原煤性质和对 产品的要求进行权衡确定 。直径过大 ,会造成小粒 度物料的离心系数降低 ,不利于小粒度物料的分选 ; 直径过小则入选上限受到限制 。而柱体高度同样也 是一个限制因素 ,过短会造成液流的不稳定 ,使分选 效率降低 ,但过大又会使分选效果变坏 。因此 ,出厂 后的旋流器圆柱直径和长度 ,以及入料口的形状和 尺寸 ,圆柱圆锥型旋流器的锥角等都是不可调的 ,其 参数的变动必须非常慎重 。而对分选效果影响最大 的中心溢流管和底流口则为可调整部位 。(1) 中心溢流管的直径和长度的变化 ,对产品质 量和产量的影响很大 ,其数值的大小要控制在一定 范围内 。因此 ,当想要改变产品的质量时 ,即可对其 进行调整 。从上述的旋流器内液流的运动规律中可 看出 ,当溢流口直径增大时 ,旋流器相同半径处的轴 向速度增大 ,轴向零速半径随之增大 ,致使轴向零速 面内的上升液流区的物料增多 ,精煤产量提高 ;但过 大时 ,矸石量会增多 ,精煤质量要变坏 。同理 ,轴向 零速面半径减小时 ,精煤出量减少 ,但可提高精煤质 量 。而当溢流管长度增长时 ,溢流管下端至锥体下 部的距离缩短 ,使被选物料的实际分选密度增大 ,从 而使精煤质量变坏 ,反之 ,则可提高精煤质量 ,但精 煤出量减少 。另外 ,溢流管的壁厚同样对分选精度 有一定的影响 。当溢流管壁增厚时 ,溢流管与器壁 之间的空间变小 ,流层变薄 ,各断面上的切线速度加 大 ,轴向速度的零速区变宽 ,使分选精度提高 ,但过 大增加壁厚 ,对分选效果也是不利的 。因此 ,中心溢 流管的各个参数 , 既是可调节的 , 又要有一定的范 围 ,在调节时应特别注意 。(2) 底流口尺寸的大小对分选效率和产品质量 影响也较大 ,当底流口缩小时 ,被选物料的实际分选 密度明显提高 ,则零速区半径增大 ,精煤产量增多 ,但 底流口也不可过小 ,以防造成挤压分离 ,恶化分选效 果 ,堵塞底流口 。因此当入选难选煤或中煤再选时 ,15图 2 旋流器内液流切向速度分布图轴向速度则随着半径的减小 ,由器壁处的负值 逐渐变为正值 ,将旋流器内液流轴向速度等于零的各点连接起来 ,可以描绘出一个近似圆锥面的网络面见图 3 (a) 。圆锥形面的内部为上升液流区 ,外部 为下降流区 。关于轴向零位面的范围 ,有学者在试 验的基础上研究得出 : 轴向零位锥面的锥底直径与旋流器直径 、溢流口直径 、底流口直径有关 ,其锥顶 与底流口处的空气柱表面重合 。而径向速度则随着 旋转半径的减小 ,在通过零位后变为负值 。如图 3( b) 所示 ,径向速度零位线为一斜线 ,是一个分界线 ,界线外的径向速度朝向器壁 ,形成外向流 ,界线内的 径向速度方向朝内 ,形成内向流 。分界线的位置是随着旋流器的结构 ,特别是随着旋流器的溢流管直径的改变而变化 。(a) 轴向速度分布图( b) 径向速度分布图图 3 旋流器内液流轴向 、径向速度分布图第 1 期2003 年 2 月选煤技术no . 1coal preparation technology feb. 2003文章编号 :1001 - 3571 (2003) 01 - 0016 - 02跳汰机新型排料装置分离效果的分析与研究贾长龄1 ,余金华2(11 安徽理工大学 ,安徽 淮南232001 ;21 浙江大学 ,浙江 杭州310027)摘要文章介绍了一种新型跳汰机简易排料系统和该系统对提高产品分离精度的效果 。关键词跳汰机简易排料系统中图分类号 : td942 + 11铲板分离效果文献标识码 :a试验在 xd2532 型筛下空气室跳汰机上进行 。铲板插入床层中的位置就是产品分离线的位置 。因 此 ,需对床层的分布状况进行分析 ,以确定铲板的合 理位置 。采样点位于排料口前端 , 由上至下分为 5 层取样 ,每份煤样都做浮沉实验 。从整体看 ,跳汰过程可看作理想的按密度扩散 过程 。依照 fokkerplanck 方程 ,颗粒在床层中的分 布近似为正态或半正态分布1 。正态分布曲线最高 峰代表某粒群在床层中最集中的点 ,是该粒群在床 层中的分布中心 。各密度级物料正态分布见图 2 。1引言现有的跳汰机将床层分离成产品是通过溢流堰实现的 。床层中高于溢流堰的部分作为溢流产品分 离出去 ,低于排料口上沿的则作为底流排出 。通常这两个 高 度 差 最 少 200mm , 这 就 必 然 存 在 分 离 误差1 3。通过对跳汰机床层分布和排料系统深入研究 ,在原有排料装置基础上 ,增加一铲板 。铲板安装在跳汰机上 ,以油缸为动力 。铲板插入床层的位置 根据煤质及床层厚度可以调节 。在某选煤厂进行的生产试验表明 ,加入的铲板能有效地切割床层 ,大大 提高了产品分离的精度 ,有效地增加了精煤的产率 。2铲板位置的确定铲板在跳汰机内的安装位置如图 1 所示 。图 2 各密度级物料正态分布图从图中可以看出 , 116 高密度物料集中在床层的下部 ,中间密度级物料在各床层中的分布则是较均匀的 。可见床层的分层效果比较理想 。根据观测的结果 ,结合该选煤厂对产品煤的实 际要求 , 计 算 得 出 铲 板 的 初 始 位 置 应 在 筛 板 上 方300mm 处 。图 1 铲板在跳汰机内示意图收稿日期 :2002 - 11 - 04第 1 作者 简 介 : 贾 长 龄 ( 1946 - ) 男 , 江 苏 省 镇 江 市 人 , 副 教 授 。现 任 安 徽 理 工 大 学 高 等 教 育 所 所 长 。电 话 : 0554 -6668074 。底流口直径要比入选易选煤时小 ,反之可取大一些 。影响 ,因此 ,在生产实践中 ,根据煤质情况选用合适的重介质旋流器 ,再加以适当的调整 ,分选出符合要 求的产品 ,不失其为一种提高选煤效率和经济效益的最佳方法之一 。4结论重介质旋流器的结构参数对分选效果有不同的16sele ct e dco nt e nt s & engli s h ab stra ct sno . 1 ( fe b . is sue ) 2003 , serial no . 175coal preparatio ntec hnolo gy2003 no . 1( total 175)bimo nthly ge neralcountermeasures for the main ecological problems resulted fromli shuzhi (1)western coal developmentsponsor :tangshan branch , research instituteabstract : with respect to weak environment , semi - arid and ar2id characteristics at western area , the paper describes the main ecological problems resulted from western coal development and advances some countermeasures for dealing with them.keywords : western , coal , environment , countermeasureseveral advanced coal sulphur removal technologies and thecoal sulphur removal technologies suitable to the coal mined atchina coalcoal preparation specialiedcommittee , china coal societycoal industry technology committeenational cwm engineeringtechnology research centerliang j ingang et al (4)western area of chinathe state - of - art and development trend of pressure filterli shanwen (7) abstract : analyzing on the development course and practical ap2 plication of pressure filter , the paper elaborates on the present state and existing problems in relation to processing parameters. key structure and automatic control , and thus advances some sug2 gestion on development of the pressure filter in future .keywords : processing parameter , structure , intelligence , devel2opment trendprospect for application of moving bed screen j ig in sorting stonetao youjun (9) te st a nd re se arc hmicrostructure of fine coal ash slag and experiment comparisoncoal preparation associationof china coal industrychief editor : liu fengdeputy chief editor : sun fuxinginternational standardperiodical publication code : issn 1001 - 3571internally unifiedperiodical publication code : cn 13 - 1115tdcoden : xjuiayli qiang et al (11)of carbon removal methodsabstract : research has been made on microstructure of fine coalash slag by using transmission electron microscope , in which , a new consideration has been put forward , that is improving fine coal ash slag activity by means of reduction of residual carbon in fine coal ash slag. three processes such as tribo - electrostatic separation , fluidized bed separation and conventional flotation separation and conventional flotation separation are used for that . the quantization analysis has been made on the carbon reduction performance of the three methods. the study indicates these de - carbon methods can be significantly used for reference in dealing with the problems found in comprehensive utilization of fine coal ash slag.keywords : fine coal ash slag , residual carbon , carbon removal method , experimental comparisonresearch on regulation of structural parameters of dense mediumcyclone and the separation performance obtainedzhang yashan (14)edited & published byeditorial department of ”coalpreparation technology”address : no . 21 , xinhua west road , tangshan city , hebei province , p. r. chinapostcode : 063012tel : 0086 - 0315 - 28169620086 - 0315 - 7759357fax : 0086 - 0315 - 2829275e - mail : xmjsbjb heinfo1netdistributor for oversea :china publishing and foreigntrading corporationp. o. box : 782 , beijing , chinaabstract : the paper expounds the separation principle and structural parameters of dense medium cyclone and summari2zes the effect of structural parameters of dense medium cyclone on separation effectiveness.keywords : dense medium cyclone , centred air core , line of equal density , surface of zero velocityanalysis and study on separation performance of noval material discharge device used in j igj ia changling et al (16) abstract : the paper presents a noval simple material discharge system used in jigging machine . it also describes the performance of higher product separation precision obtained through application of the system.keywords : jigging machine , shovel plate , separation performancefeasible study on clean coal sulphur removal and ash reduction in lingshan coal preparation plantzhang hongbo et al (18) te c hnolo gy a nd exp erie nc e sapplication of belt cold bonding connection technology in laoyingshan coal preparation plantgao yingqi (20) abstract : elaboration is made in the paper on performance of cold bonding material as well as cold bonding technology and technical standard. it points that maintenance cost can be considerably cut down by use of the cold bonding belt connection technology in washery , therefore evident economical profit can be gained.keywords : cold bonding material , technology of belt connection by cold bonding , belt joint sectioning , joint , binderapplication of three - product dense medium cyclone in gongwusu coal preparation plantrenovation of driving system of rake thickener at xiaoqing collieryrenovation of dense medium preparation system in linhuan coal preparation plant coal bunker cleaning by use of multifunction high pressure water j et cleaner application of apn18s6 filter press in yungang mine coal preparation plantzhu xiaolizhao shihua et alxu j unjie et alyan yunsheng et al(22)(24) (25) (26)zhao haiyang (27)the problems found in coal slurry treatment in coal preparation plant and the countermeasuresran j incai et al (29) application of t710500 three - product dense medium cyclone in qixing coal preparation plantwang lijian et al (31)qu j ianwu (34)preparation of cwm by use of coal slurry and its application is sue di sc u s sio nan investigation into technical renovation program of fangezhuang mine co . coal preparation plantfan zhongxiang (36)(38)an approach to elimination of undesirable performance of iron removerfeasible analysis on application of moving screen bed j ig in power plant using coal gangue as fuelli zhishan liantaocheng shaohua et al(40)(42)investigation into calculation of organic efficiency of coal cleaning auto matio n of co al prep aratio nlresearch on the technology of web - based data collection at production site of coal preparation plantxu changkai et al(44)(46) (48) (50) (52)research on fuzzy control - based coal aut
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 2026年食管癌术后护理查房课件
- 香料分馏工岗前岗位适应能力考核试卷含答案
- 液晶显示器件彩膜制造工安全培训水平考核试卷含答案
- 高炉炉前工岗前实操熟练考核试卷含答案
- 金属材涂层机组操作工安全文明评优考核试卷含答案
- 实景地理信息采集员创新实践强化考核试卷含答案
- 客车司机岗位进度管理考核试卷含答案
- 机制地毯修整工7S考核试卷含答案
- 冲印师安全强化知识考核试卷含答案
- 胃食管反流护理方法
- 银川创投集团全资子公司银川商功人工智能科技有限公司公开招聘人工智能工程师等专业技术人员笔试备考试题及答案解析
- 血管内导管相关性血流感染预防与诊治指南
- GB/T 7251.3-2026低压成套开关设备和控制设备第3部分:由一般人员操作的配电板(DBO)
- 2027贵州航天电器秋季招聘284人考试参考题库及答案解析
- 钢筋弯曲机使用安全要求培训
- 2026年上海高考英语真题试卷(春考+秋考)完整版(含答案、听力原文、详细解析、满分范文)
- 2026年产前筛查与诊断知识课件
- 2026年秋季开学高二学生:学业水平考试备考课课件
- 考研政治马克思主义基本原理核心知识点系统梳理框架
- (物理)2027版高中《基础自测小纸条》必修2(默写+背诵版)
- 考研形近易混词汇 (二)
评论
0/150
提交评论