针座规格书.doc

产品规格书Product Specifcation作 成审 核批 准1 适用范围SCOPE 本规格书适用于20P大电流大脚针座2制品名称及产品编号 PRODUCT NAME AND PART NUMBER产品型号Part Number产品名称 Product Name20P大电流大脚针座3温度范围 Temperature Range项 目 Item规 格 Standard范围Temperature Range工作温度working temperature 25C + 80C贮藏温度Stockage temperature40C + 85C4默认测试条件 Default test conditions项 目 Item测 试 条 件 Test Condition411默认测试条件Default test conditions在具体试验方法中如无其他规定，试验样品应先在：环境温度：（1828）、空气相对湿度：45%75%、大气压力：86kPa106 kPa条件下放置24H后，然后再进行试验，样品的预处理条件和默认的试验条件下测试。Specific test methods in the absence of other provisions in the test sample should first: ambient temperature: (18 28) , relative humidity: 45% 75%, Atmospheric pressure: 86kPa 106 kPa placed under the post-24H, and then further tests, the sample pretreatment conditions and the default test conditions, test.5性 能 PERFORMANCE】51电气的性能 Electrical Performance项 目 Item条 件 Test Condition规 格 Requirement511接触电阻Contact resistance插配阴阳连接器后,设置毫欧姆电阻分选仪的规定接触电阻值。毫欧姆电阻分选仪的两个探头与压接后的绝缘层压线脚相接。如果红灯亮表示不合格，绿灯亮同时内部喇叭响合格。测试时所形成的回路是不超过 100mV 100mA的电路。Plug connector with yin and yang, set ohm resistor sorter cents provisions of the contact resistance. Milliohms resistance sorter of the two probes after crimping insulated and laminated wire connecting pin. If the red light is that the failure, the green light at the same time passing the internal speaker sound. The test loop is formed by the circuit does not exceed 100mV 100mA.30m512绝缘电阻Insulation resistance先将试验样品的所有接端交错连接成两组，再按下述方法施加规定的试验电压，测量绝缘电阻。在第一组接端与接到外壳或第二组之间；在第二组接端与接到外壳或第一组之间；将绝缘电阻表插上电源，将被测物的两端分别接在“接地”（E）及“线路”（L）两接线柱上；测量电压： 500V Dc 。First test samples of all the access side connection into two groups of staggered, and then impose the following methods prescribed test voltage, insulation resistance measurement. In the first group of connected clients and between the second group received a shell or; in the second group received access terminal and the shell or between the first group; the insulation resistance table plugged both ends of the measured object, respectively connected to the ground (E) and line (L) terminal on the two; measuring voltage: 500V Dc.20P大电流大脚针座50M513耐压Pressure先将试验样品的所有接端交错连接成两组，尽量使每组内不存在互相邻近的接触件，再施加规定的试验电压。在第一组接端与接到外壳或第二组之间；在第二组接端与接到外壳或第一组之间。相邻接触件之间或地线之间施加AC 500v（50hz，有效值； 1min）。First test sample to connect all the access side staggered into two groups, within each group does not exist as far as possible near the contacts with each other, and then impose conditions on the test voltage. In the first group received access terminal and the shell or between the second group; in the second group received access terminal and the shell or between the first group. Between adjacent contacts or between the ground to impose AC 500v (50hz, RMS; 1min). 无击穿现象No Breakdown52机械的性能 Mechanical Performance项 目 Item条 件 Test Condition规 格 Requirement521插入力及拔出力Insertion force and withdrawal force固定插座，以每分钟253mm速度插入或拔出插头。Fixed socket, to 25 3mm per minute rate of insertion or pull the plug.类别sort插入力Insertion Force拔出力Withdrawal Force20P大电流大脚针座5.0Kgf1.5Kgf 522PIN保持力Terminal and terminal block retention固定接插件，以每分253mm速度沿电线轴方向对装入端子座中压接好端子的导线施加拉力。Fixed connector to 25 3mm per minute speed along the wire axis into the terminal blocks in the direction of a good terminal crimping wire Shijia La Force。20P大电流大脚针座 14.7N 0.3 kgf Min523往返插拨From pluggable固定对应配套接插件，以每分钟插拔303次的速率,插拔 50次。 Fixed the corresponding matching connector to plug per minute 30 3 times the rate of plug 50.接触阻抗ContactResis-tance30mMax.53环境性能及其他Environmental Performance and Others项 目 Item条 件 Test Condition规 格 Requirement531耐高温性High temperature resistance将试样放在 90的高温箱内，温度偏差为2，时间为 8h，再在常温下放置 24h后检查。The sample placed inside the high temperature 90 , the temperature deviation of 2 , time of 8h, and then put 24h at room temperature after the inspection.外 观Appearance无损坏No Damage接触阻抗ContactResistance30mMAX532耐低温性Low temperature tolerance将试样放在 -40的低温箱内，温度偏差为2，时间为 8h，再在常温下放置 24h后检查。 The sample placed inside the low temperature -40 , the temperature deviation of 2 , time of 8h, and then put 24h at room temperature after the inspection.外 观Appearance无损坏No Damage接触阻抗ContactResistance30mMAX5.3.3焊接性能Welding performance连接器在焊接前浸入1/3环保助焊剂，在浸入温度在2405的锡槽中，历时3.0S后取出。Before the immersion in the solder connector 1/3 of the economic environment to help welding,andthen put 24H at a temperature 2405 tin bath,after the last 3.0Sout.沾敷性沾敷面积90%5.3.4焊接耐热Soldering heat接插件浸入2405的锡槽中，历时（被焊接金属5S，本体5S）后取出。2405 connector immersion tin bath,which lasted (by welding metal 5.0S,body 5S) after the removel.外观Appearance无损坏No damage535盐雾Salt 把试验样品从试验箱顶悬挂下来（平板试验样品需使受试面与垂直方向成 30角），采用浓度为（50.1） %(质量百分比)的氯化钠溶液，PH值在 6.57.2之间；温度(352) ；连续雾化 16h,试验后用流动的蒸馏水轻轻洗去表面沉积物。在常温常湿条件下恢复（12）h后检查试验样品。 The test sample from the chamber, hanging off the top (flat surface of test samples required to make subjects and vertical direction at 30 angle), by concentration (5 0.1)% (mass percentage) of sodium chloride solution, PH values of 6.5 between 7.2; temperature (35 2) ; continuous atomization 16h, test the flow of distilled water with a gently wash away the surface sediments. At room temperature and humidity conditions, restoration of (1 2) h after the inspection test sample.外观检查。试验后，五金件应无露出底金属的严重锈蚀。（使用预镀好的型材，其落料面允许有不影响其性能的轻微腐蚀。）Visual inspection. After the test, there should be no exposed hardware end of the serious corrosion of metal. (Using the pre-plating a good profile, the drop does not affect the material surface allowed the performance of minor corrosion.)536温度循环Temperature cycling线束耐温度变化试验，在不工作状态进行。根据试样的安装位置将工作温度值和上限工作温度值作为温度，在每一种温度中的暴露时间为12H，温度转换时间不大于 10min，循环次 6次。在常温下放置 24h后检查。Harness temperature resistance test does not work in the state. According to the installation location of the sample temperature and the upper limit of the working temperature value as the temperature, the temperature in each of the exposure time was 1 2H, temperature conversion time of less than 10min, cycle times 6 times. After 24h at room temperature, place check.外观 AppearancE无损伤 no Damage接触电阻 Contact resistance30m Max.绝缘电阻 Insulation Resistance100M Min.接插件和电线压接处的电压降Crimp connectors and wire voltage drop Office2.5mV Max5.3.7振动Vibration产品应能经受X、Y、Z三个方向的扫频振荡试验。产品在不工作及正常安装状态经受试验。振动试验的检测点一般定为试验夹具与试验台结合处。频率：1025HZ；振幅：1.2mm；频率：25500HZ；加速度：30m/s2;扫频速率：1oct/min；每一方向试验时间：8H。有对配件：插合接插器，串联在直流电源上，允许电流100mA；并模拟正常工作状态；其它要求同无对配件的振动试验。Products should be able to withstand X,Y,Z three drections sweep vibration test,the state stood trial. Vi