LT彩电系列.doc

九九九 999金三角牌压电陶瓷滤波器系列产品规格书SPECIFICATION FOR JINSANJIAO PIEZO-CERAMIC FILTER 景德镇市景华裕丰电子有限公司JINGDEZHEN JINGHUA YUFENG ELECTRONICS CO. LTD地址：景德镇市朝阳路543号 TEL(FAX)九九九999 压电陶瓷滤波器规格书(LT6.5MB、LT6.0MB、LT5.5MB、LT4.5MB)SPECIFICATION FOR PIEZO-CERAMIC FILTER (LT6.5MB、LT6.0MB、LT5.5MB、LT4.5MB)一 、技术要求(Characteristic)序号 项 目 单位 技 术 指 标( Requirements )NOItemUnitLT6.5MBLT6.0MBLT5.5MBLT4.5MB1品名NominalMHZ6.56.05.54.523dB带宽3dB Band widthKHZ808075603插损Insertion Loss(dB)dB6.06.06.06.0420dB带宽20dBBand widthKHZ6306005505305波动(Ripple)dB1.01.01.01.06阻带SpuriousResponsedB25（F01MHZ）25（F01MHZ）25（F01MHZ）20（F0-1MHZ）F0+0.8MHZ ）7额定电压With standing VoltageVDC505050508绝缘电阻Insulation ResistanceM1001001001009温度特性Temperature CharacteristicF/F00.5%0.5%0.5%0.5%10产品外形Dimentions见图2 (Figure2)见图2 (Figure2)见图2 (Figure2)见图2 (Figure2)11测试电路Test Circuit见图1 (Figure 1)见图1 (Figure 1)见图1 (Figure 1)见图1 (Figure 1)RG+R1=R2=470RG+R1=R2=470RG+R1=R2=600RG+R1=R2=1KLT-MB1九九九999二、试验方法 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS 1. 可焊性 Solderability 试验条件：产品的引线端子浸入2355的锡锅中，浸到端子离根部2mm处，持续时间为2.00.5S. Test conditions:After terminals were clipped up to 2mm from the terminal root in soldering bath at (2355)for2.00.5 sec. 要 求：浸润面积大于90%，浸润良好. Requirements:at least 90% of the immersed terminal shall be covered by solder coating. 2. 引出端强度 Lead Strength 试验条件：采用GB2423.29中试验Ua1（拉力），拉力5N，时间10S1S. Test conditions:Force of 0.5Kg is applied to each lead in axial direction for 101S. 要 求：外观无可见损伤,电性能应符合表1要求. Requirements:No mechanical damage and the measured values shall meet table 1. 3. 耐焊接热 Resistance to Soldering heat 试验条件：产品的引线端子浸入2605的锡锅中，浸到端子离根部2mm处，持续时间101S，恢复时间242h. Test conditions:After immersing the terminals up to 2mm to filters body in soldering bath (2605)for101 sec.,filter shall be measured after being placed in natural condition for 242 hour. 要 求：外观无可见损伤,电性能应符合表1要求. Requirements: No mechanical damage and the measured values shall meet table 1. 4. 温度快速变化 Thermal Shock LT-MB-2 九九九999试验条件：-10+70，5次循环，持续时间30分钟，恢复时间242小时. Test conditions:After temperature cycling of -10(30 minutes) to +70 (30 minutes ) was performed 5 times, filter shall be measured after being placed in natural condition for 242 hour. 要 求：外观无可见损伤,电性能应符合表1要求. Requirments: No mechanical damage ane the messured value shall meet Table 1. 5. 振动 Vibration 试验条件：频率范围1055Hz，振幅1.5mm，三方向各2小时. Test conditions:Filter shall be measured after being applied vibration as below: Vibration Freq. :10 to 50Hz; Amplitude :1.5mm ; Directions : 3 axial directions Time : 2 hour/each direction 要 求：外观无可见损伤,电性能应符合表1要求. Requirments: No mechanical damage ane the messured value shall meet Table 1.6. 跌落 Random Drop 试验条件：产品从1米高的上空往木板落下,反复8次.Test conditions:Filter shall be measured after 8 times random dropping fromthe hight of 1 m to concrete floor. 要 求：外观无可见损伤,电性能应符合表1要求. Requirments: No mechanical damage ane the messured value shall meet Table 1. 7. 高温 High temperature 试验条件：85，持续时间16小时. Test conditions:After being placed in a chamber (Temp.:85)for 16 hours,filter shall be measured after being placed in natural condition for 1 hour. 要 求：外观无可见损伤，电性能应符合表1要求. Requirements:No mechanical damage ane the messured value shall meet Table 1.LT-MB3 九九九9998. 低温 Low temperature 试验条件：-40，持续时间2小时. Test conditions:After being placed in a chamber (Temp.:-40) for 2hours ,filter shall be measured after being placed in natural condition for 24 hour 要 求：外观无可见损伤，电性能应符合表1要求. Requirements:No mechanical damage ane the messured value shall meet Table 1. 9. 恒定湿热 Humidity 试验条件：温度40，湿度9323%，持续时间96小时，恢复242小时. Test conditions:After being placed in a chamber(Humi.:9095%RH, Temp.:402) for 96 hours,filter shall be measured after placed in natural condition for 24 hour 要 求：外观无可见损伤，电性能应符合表1要求. Requirements:No mechanical damage ane the messured value shall meet Table 1. 10. 中心频率温度特性 Temperature Characteristics 在-20+80内频率变化F/F00.5%. Filter shall be measured within -20 to +80 temperature range .表1Table 1项目(Item)Limit Value3dB带宽变化(3dB Bandwidth)30KHz.20dB带宽变化(20 dB Bandwidth)40KHz.插入衰耗变化(Insertion Loss )2dBLT-MB4 九九九99911.包装Package 为了保护产品在储存和运输中免受损害，有必要对产品进行包装（外层和内层包 装）。在包装纸上，应有下列要求： To protect the products in storage and transportation, it is necessary to pack them (outer And inner package).On paper pack, the following requirements be requested11-1.标记和尺寸Dimensions and Mark 外包箱应注明警告（防潮，向上）标记，标记位置居中（如图所视） At the end of package, the warning (moisture proof, upward put) should be stick to it and mark stick in the middle of the side of package(see below) 包装箱尺寸Dimension of package length:245mm,heigh:75mm,width:100mm11-2.标记内容见以下标注Mark (see below) 名称滤波器气候类别型号LT MB标准代号数量日期10-3 包装材料及包装方法说明Section of package 包装箱用瓦楞纸制成,每只包装箱有10