同步带、轮.doc

目 录一、同步带21.简单认识22.类型3A:梯形齿工业用橡胶同步带3B:圆弧齿工业用橡胶同步带33.详细参数4MXL型4XL型5L型6H型7T型 （节距=5.00/10/20mm）8AT型11HTD型（圆弧齿）12二、同步轮171.圆弧齿同步带/同步轮17HTD-3M17HTD-5M18HTD-8M19HTD-14M202.T型同步轮21一、 同步带1. 简单认识同步带传动是由一根内周表面设有等间距的对闭环形胶带和相应的带轮所组成。工作时，带齿与带轮的齿槽相咬合，是一种咬合传动，因而具有齿轮传动，链传动和带传动的各自优点。本公司销售的同步带具有优良的耐屈扰性能，伸长率小，强力高等优点，还具有耐油，耐热，耐老化，耐臭氧，抗龟裂等优良性能。本公司供应同步带型号30余种，规格2000多种，并生产配套带轮，完全能满足用户的设计使用要求。同步带及带轮损伤原因及对策损 伤 状 况原 因 对 策 带背胶软化1 高温2 张紧轮停转3 粘上油类1 改善环境温度2 检查，调整涨紧轮3 不要粘上油类或改换耐油皮带皮带纵向龟裂1 皮带超出带轮的边沿连转。2 皮带卷上了带轮的档边3 按装皮带时，强行越过或拖入带轮档边1 调整带轮的位置2 增强轴承刚性，并固定牢靠3 A：拆下档边 B:缩短轴间距离，装上皮带 C：放松涨紧轮装上皮带抗张体部分的断裂掺进杂物或尖锐锋利的残渣改善环境 增强防护罩皮带收缩粘上了苯胺点低的芳香族类油料不让油料粘上，使用耐油性能好的皮带运行时噪音大1 皮带涨紧力太大2 两轴的平行失准3 皮带的宽度大于带轮的直径4 负载过大5 皮带与带轮咬合不良1 减低涨紧力（不跳齿为准）2 调整带轮的定位3 检查设计4 检查皮带与带轮带轮齿磨损1 负载过大2 皮带的张力过大3 带轮的材料不好4 参入磨损性粉尘1 检查设计2 降低张紧力3 使用硬度高的材料，表面进行硬化处理4 改善环境，增强防护罩看起来伸长了1 轴间距推短了2 带轮材质软1 调整轴间距离，加固轴承支承点2 带轮使用硬质材料进行表面硬化处理2. 类型A:梯形齿工业用橡胶同步带型 号 节 距齿 高带 厚角 度MXL2.0320.511.1440XL5.0801.272.3050L9.5251.913.6040H12.72.294.3040XH22.2256.3511.2040XXH31.7509.5315.7040T2.52.50.71.3040T551.202.2040T10102.504.5040T20205.008.0040AT551.202.7050AT10102.505.0050AT20205.008.0050B:圆弧齿工业用橡胶同步带齿 形 代 号型 号节 距齿 高 带 厚HTD2M20.751.363M31.172.45M52.063.88M83.366.0014M146.0210.0020M208.4013.20STPD/STSS2M20.761.36S3M31.142.20S4.5M4.51.712.81S5M51.913.4S8M83.055.3S14M145.3010.2RPP/HPPDRP2M20.761.36RP3M31.151.9RP5M51.953.5RP8M83.205.5RP14M146.00103. 详细参数同步带规格，型号，尺寸表 MXL型（节距=2.032MM）规 格节 线 长齿 数规 格节 线 长齿 数规 格节 线 长齿 数21MXL52.832661.6MXL156.4677104MXL264.1613022MXL54.862762MXL158.578105MXL266.1913124MXL60.963063MXL160.5379106MXL268.2213226MXL67.063364MXL162.5680108MXL274.3213528MXL71.123565MXL166.6282109MXL276.3513629MXL73.153666MXL168.6683110MXL280.4213830MXL77.223868MXL172.7285111MXL282.4513932MXL81.284069MXL176.7887112MXL284.4814034MXL87.384370MXL178.8288113MXL288.5414236MXL91.444571MXL180.8589115MXL292.6114437.6MXL95.54772MXL182.8890116MXL294.6414538MXL97.544872.8MXL184.9191118MXL300.7414839MXL99.574973MXL186.9492119MXL302.7714940MXL101.65075MXL191.0194120MXL304.8015041MXL103.635176MXL193.0495121MXL308.8615241.6MXL105.665277MXL197.1097122MXL310.9015342MXL107.75378MXL199.1498123MXL312.9315443MXL109.735479MXL201.1799124MXL314.9615544MXL111.765580MXL203.20100125MXL316.9915645MXL113.795681MXL207.26102126MXL321.0615845.6MXL115.825782MXL209.30103128MXL325.1216046MXL117.865884MXL213.36105130MXL329.1816247MXL119.895985MXL215.39106132MXL335.2816548MXL121.926085.6MXL217.42107134MXL341.3816849MXL123.956186MXL219.46108136MXL345.4417049.6MXL125.986287MXL221.49109140MXL355.6017550MXL128.026388MXL223.52110152MXL386.0819051.2MXL130.056489MXL227.58112154MXL390.2119252MXL132.086590MXL229.62113160MXL406.4020053MXL134.116691MXL231.65114172MXL430.7821553.6MXL136.146792MXL233.68115177MXL449.0722154MXL138.186893MXL235.71116180MXL457.2022556MXL142.247094MXL239.78118192MXL487.6824057MXL144.277196MXL243.84120199MXL505.9724958MXL146.307297.6MXL247.9122200MXL508.0025058.4MXL148.347398MXL249.94123240MXL609.6030060MXL152.475100MXL254.00125278MXL705.1034761MXL154.4376101MXL256.03126810MXL2056.381012 XL型（节距=5.08mm）Dimension of synchronous belt 规 格节 线 长齿 数规 格节 线 长齿 数规 格节 线 长齿 数44XL111.7622164XL416.5682326XL828.0416356XL142.2428168XL426.7284330XL838.2016560XL152.4030170XL431.8085336XL853.4416864XL162.5632172XL436.8886340XL863.6017070XL177.8035176XL447.0488344XL873.7617272XL182.8836178XL452.1289348XL883.9217476XL193.0438180XL457.2090352XL894.0817680XL203.2040182XL462.2891360XL914.4018082XL208.2841184XL467.3692362XL919.4818184XL213.3642188XL477.5294364XL924.5618288XL223.5244190XL482.695372XL944.4818690XL228.6045194XL492.7697376XL955.4018892XL233.6846196XL497.8498380XL965.2019094XL238.7647198XL502.9299384XL975.3619296XL243.8448200XL508.00100390XL990.6019598XL248.9249206XL523.24103400XL1016.00200100XL254.0050208XL528.32104412XL1046.48206102XL259.0851210XL533.40105414XL1051.56207104XL264.1652212XL538.48106424XL1076.90212106XL269.2452214XL543.56107430XL1092.20215108XL274.3554218XL553.72109432XL1097.28216110XL279.4055220XL558.80110450XL1143.00225112XL284.4856228XL579.13114460XL1168.40230114XL289.5657230XL584.20115490XL1244.60245116XL294.6458234XL594.36117540XL1371.60270118XL299.7259236XL599.44118564XL1432.56282120XL304.8060240XL609.60120574XL1457.96287122XL309.8861248XL629.92124580XL1473.20290124XL314.9662250XL635.00125612XL1554.48306126XL320.0463256XL650.24128630XL1660.20315128XL325.1264260XL660.40130670XL1701.80335130XL330.2065270XL685.80135710XL1803.40355132XL335.2866276XL701.04138720XL1828.80360134XL340.3667280XL711.20140788XL2001.52394140XL355.670282XL716.28141860XL2181.40430142XL360.6871286XL726.441431032XL2621.68516144XL365.7572290XL736.601451300XL3302.00650148XL375.9274300XL762.001501494XL3794.76747150XL381.0075304XL772.161522128XL5405.121064154XL391.1677310XL787.40155156XL396.2478316XL802.64158160XL406.480320XL812.80160 L型 节距=9.525mm规格节线长齿数规格节线长齿数规格节线长齿数67L171.4518281L714.3875510L1295.4013698L247.6526285L723.9076518L1314.45138101L257.1827300L762.0080525L1333.50140109L276.2329304L771.5381540L1371.60144113L285.7530315L800.1084540L1371.60144124L314.3333319L809.6385548L1390.65146130L333.3835322L819.1586555L1409.70148135L342.9036328L826.6887570L1447.80152143L361.9538330L838.2088574L1457.33153150L381.0040334L847.7389581L1476.38155154L390.5341337L857.2590585L1485.90156158L400.0542341L866.7891600L1524.00160160L409.5843345L876.3092619L1571.63165165L419.1044352L895.3594630L1600.20168169L428.6345360L914.4096634L1609.73169173L438.1546367L933.4598660L1676.40176177L447.6847371L942.9899694L1762.13185180L457.2048375L952.50100697L1771.65186185L466.7349382L971.55102701L1781.17187187L476.2550387L981.08103720L1828.80192191L485.7851390L990.60104728L1847.85194195L495.3052394L1000.13105731L1857.39195203L514.3554397L1009.65106765L1943.10204210L533.4056405L1028.70108840L2133.60224214L542.9357408L1036.23109863L2190.73230217L552.4558412L1047.75110870L2209.80232220L561.9859420L1066.80112881L2238.38235225L571.5060427L1085.85114915L2324.10244233L590.5562435L1104.90116934L2371.73249240L609.6064439L1114.43117980L2486.02261244L619.1365442L1123.951181028L2609.85274255L647.7068450L1143.001201148L2914.65306263L666.7570453L1152.531211192L3028.95318265L676.2871465L1181.101241406L3571.88375270L685.8072480L1219.201281418L3600.45378275L695.3373495L1257.301321675L4257.68447277L704.8574500L1266.831331988L5048.25530 H型（节距=12.7mm）规 格节 线 长 齿 数规 格节 线 长齿 数规 格节 线 长齿 数145H368.3029425H1079.5085730H1854.20146185H469.9037430H1092.2086740H1879.60148200H508.0040440H1117.6088750H1905.00150205H520.7041445H1130.3089770H1955.80154210H533.4042450H1143.0090785H1993.90157220H558.8044455H1155.7091800H2032.00160225H571.5045460H1168.4092810H2057.40162230H584.2046465H1181.1093820H2082.80164240H609.6048470H1193.8094830H2108.20166245H622.3049480H1219.2096840H2133.60168250H635.0050485H1231.9097850H2159.00170255H647.7051490H1244.6098860H2184.40172260H660.4052500H1270.00100880H2235.20176270H685.8054510H1295.40102900H2286.00180280H711.2056515H1308.10103930H2362.20186285H723.9057520H1320.80104950H2413.00190290H736.6058525H1333.50105960H2438.40192300H762.0060530H1346.20106980H2489.2196310H787.4062540H1371.60108985H2501.90197315H800.1063550H1397.001101000H2540.00200320H812.8064560H1422.401121020H2590.80204325H825.5065565H1435.101131050H2667.00210330H838.2066570H1447.801141085H2755.90217335H850.9067580H1473.201161100H2794.00220340H863.6068585H1485.901171120H2844.80224345H876.3069590H1498.601181130H2870.20226350H889.0070600H1524.001201140H2895.60228355H901.7071605H1536.701211150H2921.00230360H914.4072625H1587.501251170H2971.80234365H927.1073630H1600.201261175H2984.50235370H939.8074640H1625.601281200H3048.00240375H952.5075650H1651.001301250H3175.00250380H965.2076660H1676.401321260H3200.40252390H990.6078670H1701.801341270H3225.80254395H1003.3079680H1727.201361325H3365.50265400H1016.0080700H1778.001401350H3429.00270405H1028.7081710H1803.401421360H3454.40272410H1041.4082720H1828.801441380H3505.20276420H1066.8084725H1841.501451400H3556.00280 T型 （节距=5.00/10/20mm）规 格节线 长齿 数规 格节线 长齿 数规 格节 线 长齿数T5*100100.0020T5*480480.0096T5*885885.00177T5*115115.0023T5*500500.00100T5*900900.00180T5*130130.0026T5*505505.00101T5*910910.00182T5*150150.0030T5*510510.00102T5*940940.00188T5*165165.0033T5*525525.00105T5*990990.00198T5*185185.0037T5*540540.00108T5*995995.00199T5*190190.0038T5*545545.00109T5*10001000.00200T5*200200.0040T5*550550.00110T5*10201020.00204T5*210210.0042T5*560560.00112T5*10301030.00206T5*215215.0043T5*570570.00114T5*10451045.00209T5*220220.0044T5*575575.00115T5*10501050.00210T5*225225.0045T5*580580.00116T5*10601060.00212T5*235235.0047T5*590590.00118T5*10751075.00215T5*240240.0048T5*600600.00120T5*11001100.00220T5*245245.0049T5*605605.00121T5*11201120.00224T5*250250.0050T5*610610.00122T5*11401140.00228T5*255255.0051T5*620620.00124T5*12001200.00240T5*260260.0052T5*625625.00125T5*12151215.00243T5*270270.0054T5*630630.00126T5*12601260.00252T5*275275.0055T5*635635.00127T5*12701270.00254T5*280280.0056T5*650650.00130T5*13001300.00260T5*295295.0059T5*665665.00133T5*13801380.00276T5*300300.0060T5*670670.00134T5*13901390.00278T5*305305.0061T5*675675.00135T5*14151415.00283T5*310310.0062T5*685685.00137T5*15201520.00304T5*320320.0064T5*690690.00138T5*16301630.00326T5*325325.0065T5*700700.00140T5*17601760.00352T5*330330.0066T5*710710.00142T5*17801780.00356T5*340340.0068T5*720720.00144T5*18001800.00360T5*350350.0070T5*725725.00145T5*18801880.00376T5*355355.0071T5*740740.00148T5*19001900.00380T5*365365.0073T5*750750.00150T5*19401940.00388T5*375375.0075T5*770770.00154T5*19601960.00392T5*390390.0078T5*775775.00155T5*21202120.00424T5*400400.0080T5*780780.00156T5*21602160.00432T5*410410.0082T5*800800.00160T5*22202220.00444T5*420420.0084T5*805805.00161T5*22602260.00452T5*425425.0085T5*810810.00162T5*22802280.00456T5*450450.0090T5*815815.00163T5*28502850.00570T5*455455.0091T5*840840.00168T5*30603060.00612T5*460460.0092T5*850850.00170T5*32553255.00651T5*475475.0095T5*860860.00172T5*32903290.00658规格节线长齿数规格节线长齿数规格节线长齿数T10-260260.0026T10-10101010.00101T10-19501950.00195T10-320320.0032T10-10301030.00103T10-19601960.00196T10-340340.0034T10-10401040.00104T10-19801980.00198T10-370370.0037T10-10501050.00105T10-20202020.00202T10-400400.0040T10-10801080.00108T10-20802080.00208T10-410410.0041T10-11001100.00110T10-20902090.00209T10-440440.0044T10-11101110.00111T10-21002100.00210T10-450450.0045T10-11401040.00114T10-21602160.00216T10-460460.0046T10-11501150.00115T10-22002200.00220T10-480480.0048T10-11801180.00118T10-22502250.00225T10-500500.0050T10-12001200.00120T10-22702270.00227T10-530530.0053T10-12101210.00121T10-23002300.00230T10-540540.0054T10-12401240.00124T10-23402340.00234T10-550550.0055T10-12501250.00125T10-23602360.00236T10-560560.0056T10-12601260.00126T10-23802380.00238T10-580580.0058T10-12801280.00128T10-24302430.00243T10-600600.0060T10-13001300.00130T10-24802480.00248T10-610610.0061T10-13201320.00132T10-25002500.00250T10-630630.0063T10-13501350.00135T10-25402540.00254T10-650650.0065T10-13701370.00137T10-25502550.00255T10-660660.0066T10-13901390.00139T10-25802580.00258T10-690690.0069T10-14001400.00140T10-25902590.00259T10-700700.0070T10-14101410.00141T10-26102610.00261T10-720720.0072T10-14201420.00142T10-26502650.00265T10-730730.0073T10-14401440.00144T10-27002700.00270T10-750750.0075T10-14501450.00145T10-28002800.00280T10-770770.0077T10-14601460.00146T10-30003000.00300T10-780780.0078T10-14801480.00148T10-30403040.00304T10-800800.0080T10-15001500.00150T10-31003100.00310T10-810810.0081T10-15201520.00152T10-32303230.00323T10-840840.0084T10-15601560.00156T10-33003300.00330T10-850850.0085T10-16001600.00160T10-33403340.00334T10-880880.0088T10-16101610.00161T10-35003500.00350T10-890890.0089T10-16401640.00164T10-36003600.00360T10-900900.0090T10-16901690.00169T10-36803680.00368T10-910910.0091T10-17001700.00170T10-38703870.00387T10-920920.0092T10-17201720.00172T10-40404040.00404T10-950950.0095T10-17501750.00175T10-42804280.00428T10-960960.0096T10-17801780.00178T10-46804680.00468T10-970970.0097T10-18001800.00180T10-50605060.00506T10-980980.0098T10-18601860.00186T10-60006000.00600T10-10001000.00100T10-18801880.00188T10-62906290.00629规格节线长齿数规格节线长齿数规格节线长齿数T10-70007000.00700T10-70507050.00705T10-76007600.00760T20-10801080.0054T20-16801680.0084T20-26002600.00130T20-11801180.0059T20-17001700.0085T20-27202720.00136T20-12201220.0061T20-17601760.0088T20-27402740.00137T20-12401240.0062T20-17801780.0089T20-27602760.00138T20-12601260.0063T20-18801880.0094T20-31003100.00155T20-12801280.0064T20-20402040.00102T20-36203620.00181T20-13201320.0066T20-22002200.00110T20-47604760.00238T20-14601460.0073T20-22402240.00112T20-50005000.00250 AT型1) AT10型（节距=10mm）规格节线长齿数规格节线长齿 数规 格节 线长规 格AT10*500500.050AT10*10001000.0100AT10*15001500.0150AT10*560560.056AT10*10101010.0101AT10*16001600.0160AT10*58