客户确认书.doc

天 津 森 大 玻 璃 有 限 公 司TIANJIN SENDA GLASS CO。，LTD客 户 确 认 书CUSTOMERS AFFIRM客户CUSTOMER： 产品名称：PRODUCT ITEM:； 产品规格SPECIFICATION： 类型TYPE： 时间DATE： 文件号：DOCUMENT NO：SD-EN0001 APPROVED BY部门审核DEPT APPROVAL品质会签QUALITY DEPARTMENT制表MADE BY客户确认：CUSTOMER CONFIRMATION审 核APPROVED BYR&DDEPT采 购 确 认PURCHASING DEPT品 质 确 认QC DEPT 地址：天津市西青区中北工业园F6F8电话：02223796722 传真：02223796723 网址： 天津森大玻璃公司产品质量标准书TIANJIN SENDA GLASS CO,.LTD PRODUCT QUALITY STANDARD BOOK1.标准适用范围 本标准适用于客户所需求的 产品的生产，检验及验收确认用 This standard is used for the production, inspection and acceptance of the glass which our customer need2.引用标准： 在标准中规定的有关钢化玻璃的安全强度，实验方法和相关检验规则等，均参考中华人民共和国质量监督检验检疫总局发布的标准。 The safty strength ,test method and the inspection standard of the strengthen glass is refered by the general administration of Quality Supervision, Inspection and Quarantine of the peoples republic of china released information3.相关术语定义：标准中所用名词术语未作特别注释的均遵照国标中的名词术语来定义.relative term definition :The words and terms in the standard are define by the words and terms of national standard unless other specify notes4.技术参数Technical parameters项目名称Items参数要求Parameter requirements缺陷允许值Defects range缺陷图示说明Defects diagram备注remarks检测工具Testing tools基片品名Glass type浮法玻璃Float glass不同批次允许有轻微色差Different batch of glass allows slightly colour difference 单位：mmUnit: mm目视Eye estimate基片厚度Glass thickness412mm46mm0.2812mm0.3单位：mmUnit: mm卡尺Micrometer calipers外围尺寸Outline dimension详见图纸Refer to drawing1.0mm单位：mmUnit: mm卡尺Micrometer calipers对角线Diagonal1.5（未倒角之前二对角线之差值）1.5mm(the difference of two diagonal before rounding corners )1.5单位：mmUnit: mm卡尺Micrometer calipers倒角Corners依客户要求Refer to drawing倒角均匀R角3mm，公差：0.3mmR角3r10mm公差：0.5mmR角10mm，公差：1.0mmComers appearance uniformity单位：mmUnit: mm卡尺Micrometer calipers钻孔Drill holes依客户图纸要求Refer to drawing孔位相对偏移量1.0mm孔径公差：0.5mm,Hole,position offset10.mmHole 0ffset tolerance 0.5mm单位：mmUnit: mm卡尺Micrometer calipers丝印尺寸Silkscreen按图丝印Silk screening refer the drawing周边留光区域偏差1.0mmAround blank area tolerance1.0mm单位：mmUnit: mm卡尺Micrometer calipers重量Weight玻璃密度以2.5X103Kg/m3计算Glass density calculate2.5X103 Kg/m30.2Kg单位：KgUnit: Kg电子称electronic scale平整度Flatness参照国标3Refer to national standard32单位：mmUnit: mm厚度尺直尺Thickness gauge颗粒数Particle counts参照国标Refer to national standard半钢化无颗粒数，4mm以上全钢化在50*50mm范围内有40粒以上Than 40 particals 50*50mm area. Semi tempered glass: no particals 单位：粒Unit :grain计数框List count冲击测试Impact test单边尺寸在300mm以上的底座产品做落球测试Glass base product with single side edge over 300mm can do the impact test46mm用500g钢球由1.0米，812mm用1040g钢球由1.0米做测试，需落在玻璃的非钻孔区内玻璃不破碎为合格，玻璃底部贴胶垫Thickness46mm use 500gsteel ball form1.0m thickness 812mm use 1040gsteel ball form 1.0height onto the un hole area glass should have no broken单位：米Unit: m跌落架钢球Drop frame ball5.外观要求Appearance standard项目名称Items参数要求Parameter requirements缺陷允许值Defects range缺陷图示说明Defects diagram备注remarks检测工具Testing tools黑白点，透光，气泡。污点等类似点状Black/white dots, buble, pin holes, dots, dotshape dirt 0.2 mm不限No limit单位：mmUnit: mm菲林卡Film card 0.4 mm间隔100mm允许4点Allow 4 points between 100mm 0.6 mm间隔100mm允许2点Allow 2 points between 100mm划伤，杂物等类似线状Scratch sundries liked line shapew 0.08 mm不限No limit单位：mmUnit: mm菲林卡 Film cardw0.2mmL20mm间隔100mm允许4条Allow 4 L20mm lines between 100mmw0.35 mmL15mm间隔100mm允许3条allow 3 L15mm lines between 100mm锯齿Jaggy0.3mm内框锯齿0.3mmInner frame jaggy 0.3mm单位：mmUnit: mm菲林卡 Film card丝印色差Silkscreen colour difference依客户签样Refer to customer specimen signature漏光允许补油，不同批次允许依色卡上下一格偏差Light leakage is allowed to retouch ,different batch allowed difference in one range of the pantone colour 色卡Pantone colour磨边/崩边Edging/broken edge依客户要求Refer to customer requirement正面崩边0.1m（背面崩边0.6mm，孔位崩边1.5mm可接受）Front edge broken 0.1mm,back edge broken 0.6mm,hole edge broken 1.5mm单位：mmUnit: mm菲林卡Film card6.其他Others项目名称Items参数要求Parameter requirements缺陷允许值Defects range缺陷图示说明Defects diagram备注remarks检测工具Testing tools油墨附着力Ink adhesive force用600#3m胶粘3次，油墨不脱落Using 600#3M glue stick 3 times ink do not shed高温油墨和低温油墨（百格测试）都不允许脱落Not allowed600# 3M胶600# 3Mgule检验区域testing areaA区为装配件前部区域，B区为装配件后部区域A is the front area before the assemblies ,B is the back area after the以AB分区，遵照5项外观标准检验Partition form A and B according to the fifth surface standard to inspect检验条件Testing condition1.环境亮度在500勒克斯2.检验距离在眼视距4560cm以上3.检验角度为眼睛与玻璃为904.玻璃垂直旋转倾斜30155.检验时间为510s/pcs1 、environment brightness 500lux2 、inspect distance eye distance above 4560cm3、 glass and eyesight is 904、 the glass vertical tumen305 、inspect time 510s/pcs按双方协议要求Refer to both sides contact agreement7.HSF控制/HSF物质含量HSF controlHSF管制产品外包装箱上需贴绿色HSF标识HSF controlThe outer box of packaging should stick an HSF label物质名称Substance name物质含量(PPM)备注RemarksCdHgPbCrBr玻璃glassN.D.N.D.N.D.N.D.N.D.符号环保要求Meet environment requirements高温油墨Hightemperature ink3N.D.50N.D.N.D.低温油墨Low temperature inkN.D.N.D.N.D.N.D.N.D.备注:remarks1. 点状缺陷计算方式:(长+宽)/2.Dot defects calculate method:(length+width)/22. 轻划伤:发丝状以指甲触摸感觉不出的刮伤.Mild scratch: hair shape could not feel by finger touch3. 中度划伤:指甲触摸不易感觉出来的刮伤.Medium scratch: not easy to feel by finger touch4. 重划伤:指甲触摸可感觉出来的刮伤.Serious scratch: can feel by finger touch5. 产品最佳保存期限:未经装配的玻璃产品,最佳保存期一个月,未折包产品在符合我司要求的储存条件下一般保存期为2个月,(梅雨季节除外).Product best storage time: not assembled glass is 1 month, glass did not open the package is 2 month according to our required storage conditions,(except plum rain season)6. 最佳存放条件:包装温度255,湿度60%以下,通风干燥,远离水源及无阳光直射的场所.Best storage conditions: packaging temperture255,humidity below 60%,aeration-drying away form water and no in direct sunlight area7. 搬运及防护要求:A.搬运中须轻搬轻放,避免碰撞或未做保护在硬质台面上推拉.B.运输时防止倾倒、滑动.C.操作时请戴手套.D.勿与有机溶剂及其它化学品存放一起,避免玻璃腐蚀变质.Transportation and protection requirements: A. handle with care, avoid collide or push and pull on the hard surface without protection B avoid dumping ,slide C. handle glass with glove. D. do not store glass with organic solvent and other chemicals together, avoid glass erosion 8. 当因客户原因超过产品保存期或不符合产品存放条件所造成的质量问题,我司不承担任何责任,但为降低客户的损失,我司可协助客户返修.The quality problem cause by glass products exceed the Product expired or not according to our customer lower the losing, we can assist our customer to repair 9. 当因产品表面质量产生争议,无法用书面描述清楚时,则由双方品质部、工程部共同协商,签定限度样板,后续检验则以限度样板为准.When the disputes cause by the surface quality and can not describe by paper works ,should be discuss by each side QC and technical departments ,to sign a specification sample. The following inspection should be refer to this sample.10. 当客户收到我司标准书后,若有异议需在7个工作日内提出,若异议相关单位需签字并及时回传,如超过10个工作日后没有异议或签字回传则我司视为贵司默认,后续供货则采用本标准.After our customer received our quality standard letter, any objection should be advise within 7 working days ,if do not have any objections customer should be signed and sent back in time ,if after 10 working days did not give any objections or not signed back to our company we will regard your company is confirmed and th