纸立体纸模型.pdf

Part A Part B Part CPart DPart I Part M Part NPart O Part P Part J Part KPart L Part E Part F Part G Part H Cut out the parts and fold them along the fold lines on each PAGE01 For part B also fold back the longest glue tab on the bottom edge and glue it to the reverse side Fold back the longest glue tab on the bottom edge of part A and glue it to the reverse side Pop up Card Christmas house Assembly Instructions PAGE02 Fold back the top part of part D along the fold line and glue it to the reverse side Fold back the glue tab at the bottom of the piece you made in 8 along the fold line and glue it to the reverse side Fold back the vertical piece along the fold line and glue it to the reverse side Connect the part you made in 5 together at the glue tabs As shown in the picture attach the left glue tab on part B to the wall glue tab on part A Fold up the parts you glued together in 4 as shown in the picture while attach ing the right glue tab on part A to the back of part B Pop up Card Christmas house Assembly Instructions PAGE03 Fold part C down the middle and glue together at the back At the fold line fold back the vertical glue tab at the bottom of the piece you m ade in 14 and glue it to the reverse side Fold back the horizontal glue tab at the bottom of part F marked and glue it to the reverse side Join the chimney together at the glue tabs Attach part E Insert the piece you made in 9 into the piece you made in 6 in line with the po sition of the chimney on 6 Then glue 9 to the glue tabs on the bottom inside of 6 Pop up Card Christmas house Assembly Instructions Insert the chimney you made in 12 through the hole in part F and secure it by gluing at the left and right glue tabs on part F PAGE04 Fold back the top glue tab marked on part F at the fold line and glue it to the reverse side Then attach the glue tab on the vertical piece to the back of part F Pass the part you made in 13 through the vertical strip on the back bottom edge of part F as shown in the photo and secure it to the glue tabs on the back of the wall Glue the glue tab on the piece you made in 15 to the reverse side of part F Fold back the left glue tab marked on part F at the fold line and glue it to the reverse side Fold back the right glue tab marked on part F at the fold line and glue it to the reverse side Pop up Card Christmas house Assembly Instructions PAGE05 Fold part I down the middle and glue together at the back Pass the piece you made in 25 through the vertical strip on the top back edge of part F as shown in the photo and secure its glue tabs to the reverse side of the roof As shown in the picture attach the piece you made in 23 to the reverse side of the wall Attach part G to the roof Fold back the bottom glue tab on part H marked and glue it to the reverse side Pop up Card Christmas house Assembly Instructions PAGE06 After gluing carefully fold it up and open and close the card a few times to ch eck the mechanism Attach part L to part K Attach the glue tabs on part K to part J and the base at the glue spots Attach the glue tabs on the piece you made in 27 to the base slotting it onto the slit at the back Attach the right glue tab on part J to the glue tab at the back left corner of the house Join the left and right sides of the base together at the glue tabs Pop up Card Christmas house Assembly Instructions PAGE07 Insert the bottom glue tabs of the part you made in 36 through the slits on the base and attach them to the reverse side After gluing carefully fold it up and open and close the card a few times to ch eck the mechanism Glue the cover with the writing on it to the left half of the base 39 is the completed card when the cover is stuck on to the other half side Fold back the second glue tab from the left and right on the bottom of part M and glue them to the reverse side the parts in the photo only Attach the left glue tab on part M to the left glue tab on the back of part N Fit part O to the slot on part N and attach the right gl